Intel P4304SC2SFEN, P4304SC2SHDR, P4308SC2MHGC User Manual
Intel® Server System P4000SC Family
Quick Installation User's Guide
Thank you for buying an Intel® Server System. The following information will help you
assemble your Intel® Server System and install components.
If you are not familiar with ESD [Electrostatic Discharge] procedures used during
system integration, see the complete ESD procedures described in your Service Guide.
This guide and other supporting documents are located on the web at:
http://www.intel.com/support.
G63272-001
(This page is intentionally left blank.)
i
Table of Contents
System Overview .............................................................................................................................. 1
General Installation Process ........................................................................................................ 3
Preparing the System ....................................................................................................... 3
Remove the Side Cover ................................................................................................... 3
Remove the Air Duct ......................................................................................................... 3
Remove Processor Heat Sink(s) ................................................................................ 3
Install the Processor(s) .................................................................................................... 3
Install Heat Sink(s) ............................................................................................................ 4
Install DIMM Memory Modules ..................................................................................... 5
Install Tool-less CD-ROM or DVD-ROM Drive ........................................................ 5
Install Hard Drive ................................................................................................................. 6
Install PCI-e Card Assembly ........................................................................................... 7
Install Intel® Remote Management Module 4 NIC (optional) ....................... 9
Install RMM4 EMI Cover (optional) ............................................................................. 9
Install Alternate Serial Port (optional) ..................................................................... 9
Install Intel® RAID Smart Battery (optional) ...................................................... 10
Install Second Power Supply Module (optional) .............................................. 10
Rack Mount Configuration (optional) .................................................................... 10
Install Feet (pedestal only) ......................................................................................... 10
Install Air Duct ................................................................................................................... 11
Install Side Cover .............................................................................................................. 11
Finishing Up ......................................................................................................................... 11
Install Software ................................................................................................................. 11
Reference ............................................................................................................................................ 12
HDD Cage Cable Connection ...................................................................................... 12
Front Panel Controls and Indicators ...................................................................... 13
Cable Routing Diagram .................................................................................................. 13
ii
Warning
Warning
Caution
Tools Required
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the Intel®
Server Board and Server Chassis
Safety Information document at:
http://www.intel.com/support/
motherboards/server/sb/cs-010770
.htm for complete safety information.
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the
property of others. Copyright © 2012, Intel Corporation. All rights reserved.
Installation and service
of this product to be
performed only by
qualified service personnel
to avoid risk of injury from
electrical shock or energy
hazard.
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Flat Blade
screwdriver
Phillips*
screwdriver
Anti-static
wrist strap
Intel® Server System P4000SC Family Product Configuration
Thermal Operation and Configuration Requirements
Intel® Server
To keep the system operating within supported maximum thermal limits, the system must meet the following operating and
System
configuration guidelines:
One
Fixed
PCI Zone
Fan
(92 x 32 mm)
One
Fixed
CPU Zone
Fan
(92 x 32 mm)
Five
Hot Swap
System
Fans
(80 x 38 mm)
Hard DriveSystem Fan
4 x 3.5"
Fixed
4 x 3.5"
Hot
Swap
8 x 3.5"
Hot
Swap
P4304SC2SFEN
P4304SC2SHDR
Power Supply
One
Fixed
550W
Two
Hot Swap
460W
Two
Hot Swap
750W
Intel®
Remote
Management
Module
RMM4 Lite
P4308SC2MHGC
RMM4
= Configuration Feature
Thermal Operation and Configuration Requirements
To keep the system operating within supported maximum thermal limits, the system must meet the following operating and configuration
guidelines:
• Ambient in-let temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time. Doing so
may affect long term reliability of the system.
• The CPU-1 processor and CPU heatsink must be installed.
• DIMM Population on CPU-1: Install DIMMs in order; Channels A, B, and C. Start with 1st DIMM slot (blue) on each
channel.
• DIMM Population on CPU-2: Install DIMMs in order; Channels D, E, and F. Start with 1st DIMM slot (blue) on each
channel.
• All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied drive blank.
• The air duct must be installed at all times.
• In single power supply configurations, the second power supply bay must have the supplied filler blank installed at all times.
• The system top-cover must be installed at all times.
1
System Overview
Intel® Server System P4304SC2SFEN
System Features and Components
A
E
B
F
C
D
G
H
I
M
N
O
550W Fixed Power Supply
A
I/O Ports
B
Alternate RMM4 Knockout
C
PCI Add-in Board Slot Covers
D
AC Input Power Connector
J
K
L
E
Serial Port Knockout
F
A Kensington* Cable Lock Mounting Hole
G
Padlock Loop
H
RMM4 Knockout
I
Front Control Panel
J
5.25" Peripheral Bays
K
Heatsink
L
Fixed System Fan
M
Server Board
N
Fixed Hard Drive Carrier Tray
O
NOTE: Airduct is not shown.
Intel® Server System P4304SC2SHDR
System Features and Components
A
B
C
F
D
E
NOTE: Airduct is not shown.
G
H
I
M
Q
460W Hot Swap Power Supply (Two)
A
AC Input Power Connector (Two)
B
I/O Ports
C
Alternate RMM4 Knockout
D
PCI Add-in Board Slot Covers
E
Alternate Serial Port Knockout
J
K
L
N
O
P
F
A Kensington* Cable Lock Mounting Hole
G
Padlock Loop
H
RMM4 Knockout
I
Front Control Panel
J
5.25" Peripheral Bays
K
Heatsink
L
Fixed System Fan
M
4 x 3.5" Hot-swap HDD Cage
N
®
Intel
O
P
Q
Remote Management Module 4 Lite
Server Board
EMI Cover
2
System Overview
Intel® Server System P4308SC2MHGC
System Features and Components
A
B
C
D
E
F
NOTE: Airduct is not shown.
G
H
I
M
N
O
P
Q
750W Hot Swap Power Supply (Two)
A
AC Input Power Connector (Two)
B
I/O Ports
C
Alternate RMM4 Knockout
D
PCI Add-in Board Slot Covers
E
RMM4 Knockout
F
Alternate Serial Port Knockout
G
A Kensington* Cable Lock Mounting Hole
H
J
Padlock Loop
I
K
L
Front Control Panel
J
Heatsink
K
Hot-swap System Fan
L
5.25" Peripheral Bays
M
Server Board
N
®
Intel
O
P
Q
Remote Management Module 4
8 x 3.5" Hot-swap HDD Cage
PCI Retainer
Hot Swap Hard Drive
Bay Options and
HDD Numbering
4 x 3.5" Hot-Swap Drive Cage
A
8 x 3.5" Hot-Swap Drive Cage
B
A
0123
B
8 x 3.5" Hot-swap HDD Cage
4567
0123
Loading...