Intel IP-4GVI63, 6007002463A20 User Manual

IP-4GVI63

Series

(Industrial Board)

INSTALLATION GUIDE

Installation Guide Revision A2

6007002463A20

All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, the Manufacturer assumes no responsibility for errors or omissions.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permi ssion of Manufacturer.

TRADEMARK™

Intel

, Pentium® and Celeron® are registered trademarks of Intel®

Corporation.

Microsoft

and Windows® are registered trademarks of Microsoft

Corporation.

All products and company names are trademarks or registered trademarks of their respective holders.

These specifications are subject to change without notice.

Installation Guide Revision A2

December 2004

CONTENTS

ECTION 1 INTRODUCTION 1

1.1 Unpacking IP-4GVI63 Series 1

1.2 Description 3

1.3 Features 3

1.3.1 Graphic & Ethernet 3

1.3.2 Ultra ATA/66/100 4

1.3.3 Hardware Monitoring 4

1.3.4 I/O Shield Connector 4

1.3.5 Power-On/Off 5

1.3.6 IP-4GVI63 Series Overview 5

1.3.7 System Block Diagram 6

1.4 Specifications 7

ECTION 2 INSTALLATIONS 9

2.1 System Installation 9

2.1.1 CPU Installation 9

2.1.2 Heat Sink Installation 10

2.1.3 Memory Module Installation 11

2.1.4 Setting Jumpers 13

2.2 Board Layout 14

2.3 Jumper Setting 15

2.4 Connector’s Description 18

CONTENTS

ECTION 3 AWARD BIOS SETUP 36

3.1 BIOS Instructions 36

3.2 Main Menu 37

3.3 Standard CMOS Features 39

3.4 IDE Adapters 41

3.5 Advanced BIOS Features 43

3.6 Advanced Chipset Features 47

3.7 Integrated Peripherals 50

3.8 Power Management Setup 55

3.9 PnP/PCI Configurations 59

3.10 PC Health Status 60

3.11 Frequency/Voltage Control 62

3.12 Load Fail-Safe Default 64

3.13 Load Optimized Defaults 64

3.14 Supervisor/User Password Setting 65

3.15 Exit Selecting 66

iii

SECTION 1

INTRODUCTION

1.1 Unpacking IP-4GVI63 Series

1. Take out the IP-4GVI63 series unit from the carton box, check if the unit is

properly secure in the plastic bag.

2. Check the contents of the carton box: ¡ Industrial Board ¡ Installation Guide

¡ Floppy ribbon cable ¡ ATA-66/100 HDD ribbon cable

¡ Driver Utility ¡ COM2 ribbon cable (1 Set)

(for RS-232)

Introduction

¡ COM3 ribbon cable (1 Set) ¡ I/O Shield

(for RS-232/422/485)

3. Optional Cable ¡ USB2.0 cable (optional) ¡ COM4 ribbon cable (optional)

(for RS-232/422/485)

Introduction

1.2 Description

The IP-4GVI63 Series combines the high performance and exceptional value of Intel board. The Intel

Intel

Pentium® 4 / Celeron® processors of 1.3GHz and up to 3.06GHz,

845GV chipset with a full-featured, new generation, industrial

advanced 845GV chipset support regular socket 478-pins

Furthermore, user can set the jumper to select the mobile CPU, that memory base on the FSB 400/533MHz operation supports DDR SDRAM interfa ce. In the meantime, the 845GV chipset integrated the VGA function and an external graphics device on AGP (845GV support ADD card only). The IP-4GVI63 system memory size can be up to 2GB DDR memory, onboard

Intel

82562ET Ethernet controller (support 10/100 Base-TX Ethernet), Audio and with 4 COM ports, besides the IP-4GVI63 add one slim Floppy connector to special application.

The 82801DB I/O Controller Hub (ICH4) employs the Intel

Accelerated Hub Architecture to make a direct connection from the grap hics and memory to the integrated Ethernet controller, the IDE controllers (ATA/33 or ATA/66 or ATA/100), six USB ports that are supported USB 1.1/2.0 standard meets the performance, stability and reliability requirements.

The industrial board - IP-4GVI63 is suitable and valuable for all the industry applications, which also well support with the Windows 98/SE/ME/2000 and Windows

XP operation system.

1.3 Features

1.3.1 Graphic & Ethernet

The IP-4GVI63 is base on the Intel

845GV chipset, offers users the integration graphic, Ethernet, Audio function. The features of chipset are as below:

¡ Enhanced integrated graphics & system performance:

- 400/533 FSB support

¡ Memory:

- SDRAM PC133, DDR 266/333

- 2.0GB Max. Memory

- 2 DIMM, Non-ECC

Introduction

¡ IO Connectivity - ICH4:

- 6 Hi-Speed USB2.0 ports

- 10/100 Base-TX Ethernet

1.3.2 Ultra ATA/66/100

The ICH4 provides two channel Ultra ATA/66/100 Bus Master IDE controller, that support Ultra ATA/66/100 protocols, perfect for such demanding applications as real-time video, multimedia, and high performance operating system. A new IDE cable is required for Ultra ATA/66/100. This cable is an 80-conductor cable; however the connectors are, of course, backwards compatible with ATA/33.

1.3.3 Hardware Monitoring

Hardware monitoring allows you to monitor various aspects of your systems operations and status. The features include CPU temperature, voltage and RPM of fan.

1.3.4 I/O Shield Connector

The board is equipped with an I/O back panel. Please use the appropriate I/O shield (figure 1).

56.05

87.71

16.80

25.42

21.75

29.50

6.50

143.76

26.13

6.22

21.64

11.96

38.10

35.97

25.00

5.00

Figure 1: I/O back panel layout

Introduction

1.3.5 Power-On/Off (Remote)

The board has a single 20-pins connector for ATX power supplies. For ATX power supplies that support the Remote On/Off feature, this should be connected to the systems front panel for system Power On/Off button. The systems power On/Off button should be a momentary button that is normally open.

The board has been designed with “Soft Off" functions. You can turn Off the system from one of two sources: The first is the front panel Power On/Off the button, and the other is the "Soft Off" function (coming from the M/B　 onboard circuit controller) that can be controlled by the operating

system such as Windows

98/SE/ME/2000 or Windows® XP.

1.3.6 IP-4GVI63 Series Overview

Function / Model IP-4GVI63

¡ Chipset Intel® 845GV ¡ LCD Function / ¡ VGA Function ¡ SCSI Function / ¡ Ethernet Function ¡ Audio Function ¡ Two EIDE Interface ¡ One Floppy Interface ¡ One Parallel ¡ PCI Slots 6 ¡ AGP Slot 1 (For ADD card only) ¡ Serial Port 4 ¡ USB 2.0 Port 6 (Two for Optional USB Cable) ¡ Fan Connector 4 ¡ Slim Floppy Connector



    



Introduction

1.3.7 System Block Diagram

CRT

Device

IDE Primary

IDE Secondary

USB Port 1/2

USB Port 3/4

USB Port 5/6

FWH

AGP4X

ATA100

USB

P4 Socket 478-pins

GMCH (845GV)

760 FC-BGA

ICH4

421 BGA

Super I/O

W83627H F

DATACTRLADDR

PCI BUS

DDR266/333 X2

AC97 Audio

Codec

W83627HF

ClockVRM

Intel 82562

10/100

Base-TX

Super I/O

PCI SLOTS

Keyboard

Mouse

COM 1/2 Port

LPT Port

Floppy

COM 3/4 Port

Figure 2: System Block Diagram

Introduction

1.4 Specifications ¡ Processor:

- Intel Processor operating at 1.3GHz and up to 3.06GHz

- Intel

Pentium® 4/Celeron™ processor with socket 478-pins package,

Pentium® 4 Mobile™ processor with socket 478-pins package,

Processor operating at 1.2GHz and up to 2.4GHz

- System bus frequency at 400/533 MHz FSB

¡ Chipset:

- Intel

82845GV + ICH4 AGPset

¡ DRAM Module:

- Two 184-pins Socket

- For DDR 266/333 SDRAM memory

- Support DDR SDRAM up to 2GB (Max.)

¡ VGA Function:

- Intel

845GV Chipset integrated graphic controller

- Onboard one 15-pins VGA connector

¡ LAN Function:

- Intel

82562ET Ethernet controller

- For 10/100Base-TX Ethernet

- Onboard one RJ-45 Ethernet connector

¡ Audio Function:

- AC97 audio controller

¡ External Connector:

- One slim floppy connector

¡ Expansion Slot:

- 1 x AGP slot (for ADD card only)

- 6 x PCI slots

¡ Onboard I/O:

- On-Chip I/O integrated with K/B, Mouse, FDD, Parallel and Serial, Fast IR and Power-ON controllers

Introduction

¡ Onboard PCI / IDE:

- Intel

82801DB (ICH4) controller

- PCI rev2.2 Compliant

- ACPI Compliant Power Management

- PCI bus IDE port with PIO /Ultra DMA-100 x 2 (up to 4 devices)

¡ Rear I/O Connectors:

- PS/2 mouse and PS/2 style keyboard

- D-Sub 25-pins printer port connector

D-Sub 9-pins COM1 serial port connector for RS-232 D-Sub 15-pins VGA connector

- 2 x USB2.0 connectors

- RJ-45 Ethernet and 2 x USB2.0 connectors

- Audio for Line-In, Line-Out, MIC phone jack

¡ Internal I/O Connectors (pin-header):

- 3 x serial ports, COM2 for RS-232 and COM3/4 for RS-232/422/485 (serial cable with bracket by optional)

- 2 x USB2.0 connectors (USB cable with bracket by optional)

¡ BIOS:

- Award Plug & Play BIOS

¡ Form Factor:

- 12” x 8.7” (305 x 220mm) ATX Size

¡ Weight:

- 1.44lb (650g) ---

IP-4GVI63 series

SECTION 2

INSTALLATIONS

2.1 System Installation

2.1.1 CPU Installation

Carefully follow the steps below in order to install the CPU:

1. Check and confirm that you are going to install correctly CPU type and

pin numbers (figure 3).

2. Lift the releasing lever of the Socket 478.

3. Align the pin of the CPU against the pinholes of the Socket 478. Be sure

to pay attention to the orientation of the CPU.

Figure 3: CPU Socket

4. Push down the CPU into the Socket 478.

5. Push down the release lever and lock it against the key hook.

6. Hook the hole in ZIF clip for the CPU cooling fan onto the notch on the

socket 478.

7. Place the CPU cooling fan atop the CPU surface.

8. Push down the opposite side of the ZIF clip and hook it.

9. Slide the head of the clip to left and lock it.

10. Connect the cooling fan cable to the socket. Be careful not to place the

cable on the CPU cooling fan.

Installations

Removing a CPU:

1. Before removing the CPU, turn off the IP-4GVI63 Series power; then wait

for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools down.

2. To remove the CPU, lift the releasing lever of the Socket 478. Note: The CPU and the heat radiation plate are hot. They may cause

burns.

To remove the CPU, reverse the installation steps.

2.1.2 Heat Sink & Retention Module Installation

Make sure that good contact is made between the processors and the heat sinks & fan. Insufficient contact, incorrect types of heat sinks, fans, or thermal compound used or improper amount of thermal compound applied on the CPU die can cause the processors to overheat, which may crash the system.

Heat Sink & Fan

(For P4 processor only)

Retention Module

(For P4 Heat Sink & Fan)

Installation

Figure 4: Heat Sink & Retention Module Installation

Installations

2.1.3 Memory Module Installation

Figure 5 display the notch marks and what they should look like on your DIMM memory module.

DIMMs have184-pins and two notches, that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree angle and pressing straight d own (figure 6) until it fits tightly into the DIMM socket.

Figure 5: DIMM Memory and 184-pins Socket

Figure 6: Memory Installation

Installations

Carefully follow the steps below in order to install the DIMMs:

1. To avoid generating static electricity and damaging the DIMM, ground

yourself by touching a grounded metal surface or using a ground scrap before you touch the DIMM.

2. Do not touch the connector of the DIMM. Dirt residue may cause a

malfunction.

3. Hold the DIMM with its notch to the front side of the IP-4GVI63 Series

and insert it completely into the socket. A DIMM should be inserted into the inner socket first. Guiding the hole at each end of the DIMM over the retaining post at each end of the DIMM socket.

4. If you install two DIMMs, install the second DIMM using the same

procedure as above.

5. If DIMM does not go in smoothly, do not force it. Pull it all the way out

and try again.

6. Make sure the DIMM is properly installed and locked by the tabs on both

sides of the socket.

Removing a DIMM:

To remove the DIMM, use your fingers or a small screwdriver to carefully push away the plastic tabs that secure the DI MM at each end. Lift it out of the socket.

Make sure you store the DIMM in an anti-static bag and must be populated the same size and manufactory of memory modules.

Installations

2.1.4 Setting Jumpers

There are jumpers on the system board of the IP-4GVI63 Series. You can set the jumpers to make the necessary operations.

Figure 7: Jumper Connector

For any three-pins jumpers (figure 7), the jumper setting is 1-2 when the jumper connects pin 1 and 2. The setting is 2-3 when pin 2 and 3 are connected and so on. You could see one of the lines surrounding jumpers is thick, which indicates pin NO.1.

To move a jumper from one position to another, use needle-nose pliers or tweezers to pull the pin cap off the pins and move it to the desired position.

Installations

2.2 Board Layout

Jumper & Connector Location

KBMS1

COM1

LPT1

FAN2

CPU FAN

JP1

ATX1

DIMM1

POWER FAN

FAN1

DIMM2

VGA1

USB1

USB2

LAN

TX2

IP-4GVI63

CN1

FAN4

IDE2

CHASSIS FAN

FAN3

AGP1 ADD ONLY

PCI1

AUX IN1

CD IN1

WOL1

PCI2

PCI3

PCI4

COM2

PCI5

PCI6

REV:1.0

BAT1

JP3

IDE1

JBAT1

FDD1

USB3JPB2JCN2JPB1JCN1

2.3 Jumper Setting

Table for Jumper Location Description:

Use the information in the following table to change the jumpers.

Jumpers Functions

JP1 CPU type select JP3 Watchdog Timer setting select

JBAT1 Clear CMOS setting select

JPB1 COM3 port setting select JPB2 COM4 port setting select

Installations

In order to set up the correct configuration, here is the description about how to set the jumpers to enable/disable or change functions. All jumpers’ location please refer to jumper location diagram.

 CPU type select: JP1

Function JP1

Regular P4 CPU (Default) 1-2 On

P4 Mobile CPU 1-2 Off

y Location:

 Watchdog Timer setting select: JP3

Function JP3

NMI (Default) 1-2

Reset System 2-3

y Location:

 Clear CMOS setting select: JBAT1

Function JBAT1

Normal (Default) 1-2

Clear CMOS 2-3

y Location:

+ 50 hidden pages