Intel BOXD510MO Product Manual

Intel® Desktop Board D510MO
Product Guide

Order Number: E7451

8-001

Revision History

Revision Revision History Date

-001 First release of the Intel® Desktop Board D510MO Product

If an FCC declaration of conformity marking is present on the board, the following statement applies:

Guide

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124,

1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel® products. No license, express or implied,
by estoppel or
in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel
disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or
warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent,
copyright or other intellectual property right. Intel products are not intended for use in medical, life saving,
or life sustaining applications. Intel may make changes to specifications and product descriptions at any
time, without notice.

Intel Desktop Board D510MO may contain design defects or errors known as errata which may cause the
product to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://www.intel.com/ or by calling 1-800-548-4725.

Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2009 Intel Corporation. All rights reserved.

otherwise, to any intellectual property rights is granted by this document. Except as provided

September 2009

Preface

This Product Guide gives information about board layout, component installation, and
regulatory requirements for Intel

®

Desktop Board D510MO.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.

Intended Uses

All Intel® Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization

The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install

the Desktop Board and other hardware components
3 Updating the BIOS: a description of how to update the BIOS
A BIOS Error Messages: information about BIOS error messages and beep codes
B Regulatory Compliance: safety and EMC regulations and product certifications

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

iii

Intel Desktop Board D510MO Product Guide

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)
GHz Gigahertz (one billion hertz)
KB Kilobyte (1024 bytes)
MB Megabyte (1,048,576 bytes)
Mbit Megabit (1,048,576 bits)
MHz Megahertz (one million hertz)

iv

Contents

1 Desktop Board Features

Desktop Board Components.................................................................................11

Processor..........................................................................................................13

System Memory.................................................................................................13

Integrated Graphics Subsystem ...........................................................................14

®

Intel

NM10 Express Chipset ...............................................................................14

Operating System Support ..................................................................................14

Onboard Audio Subsystem ..................................................................................14

Legacy Input/Output (I/O) Controller....................................................................16

LAN Subsystem .................................................................................................16

USB 2.0 Support................................................................................................17

SATA Interface ..................................................................................................17

Expandability.....................................................................................................17

BIOS................................................................................................................18

PCI/PCI Express Auto Configuration ..............................................................18

Security Passwords.....................................................................................18

Power Management Features ...............................................................................19

ACPI.........................................................................................................19

Hardware Support ......................................................................................19

ENERGY STAR*, e-Standby, and ErP Compliance ....................................................22

Battery.............................................................................................................22

Real-Time Clock.................................................................................................22

2 Installing and Replacing Desktop Board Components

Before You Begin ...............................................................................................23

Installation Precautions.......................................................................................25

Prevent Power Supply Overload ....................................................................25

Observe Safety and Regulatory Requirements.................................................25

Installing the I/O Shield ......................................................................................26

Installing and Removing the Desktop Board ...........................................................27

Installing and Removing Memory..........................................................................27

Installing DIMMs ........................................................................................28

Removing DIMMs........................................................................................30

Connecting SATA Drives......................................................................................30

Installing a Wireless LAN Card in the PCI Express Full-Mini Card Slot .........................32

Installing an Intel

Connecting to the Internal Headers ......................................................................34

Connecting the Front Panel Audio Header.......................................................35

Connecting to the S/PDIF Header..................................................................36

Connecting to the Serial Headers ..................................................................36

Connecting to the Parallel Port Header...........................................................36

Connecting to the Front Panel Wireless Activity LED Header..............................37

Connecting to the Front Panel Header............................................................38

Connecting to the Front Panel USB 2.0 Headers ..............................................38

Connecting a Chassis Fan....................................................................................39

Connecting the Power Supply Cable......................................................................40

®

Z-U130 USB Solid-State Drive (or Compatible Device)..................33

v

Intel Desktop Board D510MO Product Guide

Setting the BIOS Configuration Jumper .................................................................41

Clearing Passwords.....................................................................................42

Replacing the Battery .........................................................................................43

3 Updating the BIOS

Updating the BIOS with the Intel

Updating the BIOS with the Iflash Memory Update Utility.........................................50

Obtaining the BIOS Update File ....................................................................50

Using the Iflash Memory Update Utility ..........................................................50

Recovering the BIOS...................................................................................51

A Board Status and Error Message

BIOS Beep Codes...............................................................................................53

BIOS Front-panel Power LED Blink Codes ..............................................................54

POST Error Messages..........................................................................................54

®

Express BIOS Update Utility.................................49

s

B Regulatory Compliance

Safety Standards ...............................................................................................55

Place Battery Marking .................................................................................55

European Union Declaration of Conformity Statement..............................................56

Product Ecology Statements ................................................................................57

Recycling Considerations .............................................................................57

Lead-free 2LI/Pb-free 2LI Board ...................................................................60

Restriction of Hazardous Substances (RoHS) ..................................................61

EMC Regulations ................................................................................................63

Ensure Electromagnetic Compatibility (EMC) Compliance..................................64

Product Certifications..........................................................................................65

Board-Level Certification Markings ................................................................65

Chassis and Component Certifications............................................................66

vi

Contents

Figures

1. Intel Desktop Board D510MO Components .......................................................11

2. Back Panel Audio Connectors .........................................................................15

3. LAN Status LEDs ..........................................................................................16

4. Location of the Standby Power Indicator ..........................................................20

5. Installing the I/O Shield ................................................................................26

6. Intel Desktop Board D510MO Mounting Screw Holes..........................................27

7. Use DDR2 DIMMs .........................................................................................28

8. Installing a DIMM .........................................................................................29

9. Connecting the Serial ATA Cable.....................................................................31

10. Installing a Wireless LAN Card ........................................................................32

11. Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device)..............33

12. Internal Headers ..........................................................................................34

13. Location of the Chassis Fan Header .................................................................39

14. Connecting a Power Supply Cable ...................................................................40

15. BIOS Configuration Jumper Block....................................................................41

16. Removing the Battery ...................................................................................47

17. Intel Desktop Board D510MO China RoHS Material Self Declaration Table.............62

Tables

1. Feature Summary.......................................................................................... 9

2. Intel Desktop Board D510MO Components .......................................................12

3. Audio Jack Support .......................................................................................15

4. LAN Status LEDs ..........................................................................................17

5. ENERGY STAR Requirements ..........................................................................22

6. Front Panel Audio Header for Intel HD Audio.....................................................35

7. Front Panel Audio Header for AC ‘97 Audio .......................................................35

8. S/PDIF Header .............................................................................................36

9. Serial Port Headers (COM 1 and COM 2) ..........................................................36

10. Parallel Port Header ......................................................................................36

11. Front Panel Wireless Activity LED Header .........................................................37

12. Front Panel Header Signal Names ...................................................................38

13. Front Panel USB Header ................................................................................38

14. Front Panel USB Header with Intel Z-U130 USB Solid-State Drive

(or Compatible Device) Support......................................................................39

15. Jumper Settings for the BIOS Setup Program Modes..........................................42

16. AcceptableDrives/Media Types for BIOS Recovery .............................................51

17. BIOS Beep Codes .........................................................................................53

18. BIOS Front-panel Power LED Blink Codes.........................................................54

19. POST Error Messages ....................................................................................54

20. Safety Standards..........................................................................................55

21. Lead-Free Second Level Interconnect Marks .....................................................60

22. China RoHS Environmentally Friendly Use Period Mark.......................................61

23. EMC Regulations...........................................................................................63

24. Product Certification Markings ........................................................................65

vii

Intel Desktop Board D510MO Product Guide

viii

1 Desktop Board Features

This chapter briefly describes the main features of Intel® Desktop Board D510MO.
Table 1 summarizes the features of the Desktop Board.

Table 1.

Feature Summary

Form Factor
Processor

Main Memory

Chipset
Integrated

Graphics
Audio

Expansion
Capabilities

Peripheral
Interfaces

Legacy I/O Control

Hardware Monitor
Subsystem

LAN Support

Mini-ITX ([170 millimeters [6.7 inches] x 170 millimeters [6.7 inches])

®

Passively-cooled, soldered-down dual-core Intel

Atom™ processor with

integrated graphics and memory controllers.

• Two 240-pin Double Data Rate 2 (DDR2) Dual Inline Memory Module

(DIMM) sockets with gold-plated contacts

• Support for DDR2 800 MHz and DDR2 667 MHz DIMMs

• Support for up to 4 GB total system memory (2 GB per DIMM

socket)

®

NM10 Express Chipset

Intel

®

Intel

Graphics Media Accelerator 3150 (Intel® GMA 3150) integrated

graphics subsystem with support for analog displays (VGA)

®

RealTek* ALC662 audio codec for 5.1 (6-channel) Intel
Definition Audio (Intel

®

HD Audio) and AC ’97 Audio. Included are:

High

• Back panel connectors

• Front panel microphone/headphone header with support for

®

Intel

HD Audio or AC ’97 Audio

• S/PDIF digital audio header
One PCI* bus add-in card connector
One PCI Express* Full-Mini Card slot

• Seven USB 2.0 ports:

― Four back panel ports
― Three front panel ports (via two internal headers; one header

supports an Intel® Z-U130 USB Solid-State Drive (or compatible
device)

• Two Serial ATA (SATA) 3.0 Gb/s connectors (supporting IDE and

ACHI)

Winbond* W83627TGH-I legacy I/O controller:

• Two serial port headers

• One parallel port header

• PS/2 keyboard and mouse connectors

Hardware monitoring through the Winbond legacy I/O controller,
including:

• Remote thermal sensor

• One 3-pin chassis fan header with speed control

10/100/1000 Mb/s (Gigabit) Ethernet LAN Subsystem using a RealTek*
8111DL Gigabit Ethernet Controller

9

Intel Desktop Board D510MO Product Guide

BIOS

Instantly Available
PC Technology

• Intel

• Support for Advanced Configuration and Power Interface (ACPI),

• Support for PCI Local Bus Specification, Revision 2.3

• Support for Advanced Configuration and Power Interface (ACPI)

• Wake on USB, PCI, PCI Express, PS/2, LAN, serial, and front panel

®

BIOS

Plug and Play, and SMBIOS

For more information on Intel Desktop Board D510MO consult the following online
resources:

To find information
about…

Intel Desktop Board
D510MO

Desktop Board Support http://support.intel.com/support/motherboards/desktop

Available configurations
for Intel Desktop Board
D510MO

Chipset information http://www.intel.com/products/desktop/chipsets/index.htm

BIOS and driver updates http://downloadcenter.intel.com/

Visit this World Wide Web site:

http://www.intel.com/products/motherboard/D510MO/index.htm

http://www.intel.com/products/motherboard/D510MO/index.htm

Integration information http://www.intel.com/support/go/buildit

10

Desktop Board Features

Desktop Board Components

Figure 1 shows the location of the major components on Intel Desktop Board D510MO.

Figure 1. Intel Desktop Board D510MO Components

11

Intel Desktop Board D510MO Product Guide

Table 2. Intel Desktop Board D510MO Components

Label Description

A Back panel connectors
B Serial header (COM1)
C Parallel port header
D Serial port (COM 2)
E Chassis fan header
F Main power connector
G Standby power indicator
H Processor
I Channel A DIMM 0
J Channel A DIMM 1
K SATA 1
L SATA 0
M Front panel header
N Battery
O Front panel wireless activity LED header
P Intel NM10 Express Chipset
Q USB front panel header with Intel Z-U130 USB Solid-State Drive (or

compatible device) support
R PCI bus connector
S PCI Express Mini Card connector
T USB front panel header
U Front panel audio header
V BIOS configuration jumper block
W S/PDIF header

12

Desktop Board Features

Processor

Intel Desktop Board D510MO includes a passively-cooled, dual-core Intel Atom
processor with integrated graphics and memory controller. The processor is soldered
to the Desktop Board and is not customer upgradeable.

NOTE

The board is designed to be passively cooled in a properly ventilated chassis. Chassis
venting locations are recommended above the processor heatsink area for maximum
heat dissipation effectiveness.

System Memory

NOTE

To be fully compliant with all applicable Intel® SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.

The Desktop Board has two 240-pin DDR2 DIMM connectors with gold-plated contacts.
It supports:

• DDR2 800 MHz or DDR2 667 MHz unbuffered, non-registered DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC memory

• Up to 4 GB of memory

13

Intel Desktop Board D510MO Product Guide

Integrated Graphics Subsystem

The integrated Intel GMA 3150 graphics controller features the following:

• 400 MHz core frequency

• High quality texture engine
⎯ DX9.0c* and OpenGL* 1.4 compliant
⎯ Hardware Pixel Shader 2.0
⎯ Vertex Shader Model 2.0

• 3D Graphics Rendering enhancements
⎯ 1.6 dual texture GigaPixel/s max fill rate
⎯ 16-bit and 32-bit color
⎯ Vertex cache

• Video
⎯ Software DVD at 30 fps full screen
⎯ DVMT support up to 256 MB

• Supports analog displays up to 2048 x 1536 at 75 Hz refresh (QXGA)

Intel® NM10 Express Chipset

The Intel NM10 Express Chipset is a centralized controller for the board’s I/O paths.
For more information about the Intel NM10 Express Chipset, go to

http://www.intel.com/products/chipset

index.htm?iid=prod+prod_chipset.

s/

Operating System Support

The following Microsoft* operating systems are fully supported by the Desktop Board:

• Microsoft Windows Vista* Home Basic, SP 1

• Microsoft Windows* XP Home, SP 3

• Microsoft Windows* 7 Home Basic and Starter

Onboard Audio Subsystem

The Intel Desktop Board D510MO 6-channel (5.1) onboard audio subsystem supports
both Intel HD Audio and AC ’97 Audio. The subsystem is based on the following
components:

• Intel NM10 Express Chipset

• RealTek ALC662 audio codec

The subsystem includes the following headers and connectors:

• Front panel audio header (supports both Intel HD Audio and AC ’97) , including
functionality for:

― Line out (headphones/speaker)
― Microphone in

• Three back panel analog audio jacks

• Onboard S/PDIF output header (3 pin)

14

Desktop Board Features

The front/back panel audio connectors are configurable through the audio device
drivers. Table 3 lists the supported functions

of the front panel and back panel jacks.

Table 3. Audio Jack Support

Audio Jack Line

In

Front panel – Green No Yes No No No Yes
Front panel – Pink No No No No Yes No
Back panel – Blue Yes No Yes No No No
Back panel – Green No Yes No No No Yes
Back panel – Pink No No No Yes Yes No

Line/

Front Out

Rear Out Center/

LFE

Microphone Headphones

Figure 2 shows the default assignment of the back panel audio connectors.

Item Description

A Line In
B Line Out
C Mic In

Figure 2. Back Panel Audio Connectors

NOTE

The back panel audio line out connector is designed to power headphones or amplified
speakers only. Poor audio quality occurs if passive (non-amplified) speakers are
connected to this output.

15

Intel Desktop Board D510MO Product Guide

Legacy Input/Output (I/O) Controller

The legacy I/O controller provides the following:

• Two serial ports (via onboard headers)

• One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port

(EPP) support via an onboard headers

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• PS/2-style keyboard and mouse ports

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

The BIOS Setup program provides configuration options for the legacy I/O controller.

LAN Subsystem

The LAN subsystem consists of the following:

• Intel NM10 Express Chipset

• Realtek 8111DL Gigabit Ethernet Controller for 10/100/1000 Mbits/s Ethernet LAN

connectivity

• RJ-45 LAN connector with integrated status LEDs

Additional features of the LAN subsystem include:

• CSMA/CD protocol engine

• LAN connect interface that supports the ethernet controller

• PCI bus power management
⎯ Supports ACPI technology
⎯ Supports LAN wake capabilities

LAN drivers are available from Intel’s World Wide Web site at

http://downloadcenter.intel.com/.

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 3). These LEDs indicate the operating states of the LAN.

16

Figure 3. LAN Status LEDs

Desktop Board Features

Table 4 describes the LED states when the board is powered up and the LAN
subsystem is operating.

Table 4. LAN Status LEDs

LED LED Color LED State Indicates

Activity (A) Green Blinking LAN activity is occurring.

N/A Off 10 Mbits/s data rate is selected.

Speed (B)

Green On 100 Mbits/s data rate is selected.
Yellow On 1000 Mbits/s data rate is selected.

USB 2.0 Support

The Desktop Board supports up to seven USB 2.0 ports (four ports routed to the back
panel and three ports routed to two front panel USB 2.0 headers). One of the front
panel USB headers supports an Intel Z-U130 USB Solid-State Drive (or compatible
device). The USB 2.0 ports are compatible with USB 1.1 devices. USB 1.1 devices will
function normally at USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates. Disabling High-Speed USB in the BIOS reverts all USB 2.0
ports to USB 1.1 operation. This may be required to accommodate operating systems
that do not support USB 2.0.

NOTE

Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.

SATA Interface

The Desktop Board supports two SATA channels (3.0 Gb/s) that support one device
per channel. The SATA controller supports IDE and ACHI configuration and can
operate in both legacy and native modes.

Expandability

The Desktop Board provides the following expansion capability:

• One PCI connector. The connector can support either a single PCI add-in card or a
single- or dual-slot PCI riser card.

• One PCI Express Full-Mini Card slot.

17

Intel Desktop Board D510MO Product Guide

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI
and IDE auto-configuration utilities, and the video BIOS.

PCI/PCI Express Auto Configuration

If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express
auto-configuration utility in the BIOS automatically detects and configures the
resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need
to run the BIOS Setup program after you install a PCI/PCI Express add-in card.

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup
options. If only the supervisor password is set, pressing <Enter> at the password
prompt of Setup gives the user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.

• Setting a user password restricts who can boot the computer. The password
prompt is displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, you can enter either password to boot the computer.

For instructions on resetting the password, see Clearing Passwords on page 42.

18

Desktop Board Features

Power Management Features

Power management is implemented at several levels, including:

• Software support through the Advanced Configuration and Power Interface (ACPI)

• Hardware support:

― Power connector
― Fan header

― +5 V standby power indicator LED
― LAN Wake capabilities
― Instantly Available PC technology
― Wake from USB
― Wake from PS/2 devices
― PME# wakeup support
― WAKE# signal wakeup support
― Wake from serial port

ACPI

ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.

Hardware Support

Fan Header

The Desktop Board has a 3-pin chassis fan header. See Figure 13 on page 39 for the
location of the chassis fan header.

+5 V Standby Power Indicator

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s standby power indicator, shown in Figure 4, is lit when there is
standby power to the system. This includes the DIMM socket and the PCI bus
connector, even though the computer appears to be off.

19

Intel Desktop Board D510MO Product Guide

Figure 4. Location of the Standby Power Indicator

For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification on the Intel Desktop D510MO web page at

http://www.intel.com/products/motherboard/D510MO/index.htm.

Instantly Available PC Technology

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to­RAM) sleep-state. While in the ACPI S3 sleep-state, the computer will appear to be off
(the hard drive(s) and fan will power off, the front panel power LED will blink). When
signaled by a wake-up device or event, the system quickly returns to its last known
state.

The board supports the PCI Bus Power Management Interface Specification. Add-in
boards that also support this specification can participate in power management and
can be used to wake the computer.

The use of Instantly Available PC technology requires operating system support and
PCI 2.3 compliant add-in cards and drivers.

20

Desktop Board Features

LAN Wake Capabilities

The board’s LAN wake capabilities enable remote wake-up of the computer through a
network. The LAN subsystem network adapter monitors network traffic at the Media
Independent Interface. The board supports LAN wake capabilities with ACPI in the
following ways:

• By Ping

• By Magic Packet

Upon detecting the configured wake packet type, the LAN subsystem asserts a wake­up signal that powers up the computer.

Wake from USB

USB bus activity wakes the computer from an ACPI S1 or S3 state.

NOTE

Wake from USB requires the use of a USB peripheral that supports wake from USB.

Wake from PS/2 Device

PS/2 keyboard activity wakes the computer from an ACPI S1, S3, S4, or S5 state.
However, when the computer is in an ACPI S4 or S5 state, the only PS/2 activity that
will wake the computer is the Alt + Print Screen key combination or the Power key
available only on some keyboards.

PME# Wakeup Support

When the PME# signal is asserted on the PCI bus, the computer wakes from an ACPI
S1, S3, S4, or S5 state.

WAKE# Signal Wakeup Support

When the WAKE# signal is asserted on the PCI Express bus, the computer wakes from
an ACPI S1, S3, S4, or S5 state.

Wake from Serial Port

Serial port activity wakes the computer from an ACPI S1 or S3 state.

21

Intel Desktop Board D510MO Product Guide

ENERGY STAR*, e-Standby, and ErP
Compliance

Intel Desktop Board D510MO meets the ENERGY STAR requirements listed in Table 5
when used in corresponding system configurations.

Table 5. ENERGY STAR Requirements

ENERGY STAR
Specification

v4.0 Desktop Computer

v4.0 Integrated

v5.0 Desktop Computer

v5.0 Integrated Desktop

v5.0 Thin Client Off Mode

Computer Type

Computer

Computer

Required
States

Idle State
(Cat A)

Sleep Mode
Standby Level

Off Mode
Sleep Mode
Idle State
Active State

Sleep Mode
Idle State

(Cat B)

Capability
Adjustments

With and
without Wake
On LAN (Sleep,
Standby)

With and
without
additional
internal storage

With and
without Wake
On LAN (Sleep,
Standby)

Typical
Electricity
Consumption
(TEC) Criteria

N/A

Cat A under
“desktop
conventional”
and “desktop
proxying”
operational
mode
weightings

N/A

For information about ENERGY STAR requirements and recommended configurations,
go to http://www.intel.com/go/energystar

.

The Desktop Board also meets the following international requirements:

• Republic of Korea e-Standby program

• European Union Energy using Products (EuP) directive

Battery

A coin-cell battery on the Desktop Board keeps the values in CMOS RAM and the clock
current when the computer is turned off. Go to page 43 for instructions on how to
replace the battery.

Real-Time Clock

The Desktop Board includes a time-of-day clock and a 100-year calendar. The coin­cell battery keeps the clock current when the computer is turned off.

22

2 Installing and Replacing Desktop

Board Components

This chapter tells you how to:

• Install the I/O shield

• Install and remove the Desktop Board

• Install and remove system memory

• Connect SATA drives

• Install a Wireless LAN card

• Install an Intel Z-U130 USB Solid-State Drive (or compatible device)

• Connect to internal headers

• Connect chassis fan and power supply cables

• Set the BIOS configuration jumper

• Clear passwords

• Replace the battery

Before You Begin

CAUTION

The procedures in this chapter assume familiarity with the general terminology
associated with personal computers and with the safety practices and regulatory
compliance required for using and modifying electronic equipment.

Disconnect the computer from its power source and from any telecommunications
links, networks, or modems before performing any of the procedures described in this
chapter. Failure to disconnect power, telecommunications links, networks, or modems
before you open the computer or perform any procedures can result in personal injury
or equipment damage. Some circuitry on the board can continue to operate even
though the front panel power button is off.

Follow these guidelines before you begin installing the Desktop Board:

• Always follow the steps in each procedure in the correct order.

• Set up a log to record information about your computer, such as model, serial

numbers, installed options, and configuration information.

• Electrostatic discharge (ESD) can damage components. Perform the procedures
described in this chapter only at an ESD workstation using an antistatic wrist strap
and a conductive foam pad. If such a station is not available, you can provide
some ESD protection by wearing an antistatic wrist strap and attaching it to a
metal part of the computer chassis.

23

Intel Desktop Board D510MO Product Guide

CAUTION

Failure to ensure appropriate airflow may result in reduced performance of both the
processor and/or voltage regulator or, in some instances, damage to the board.

All responsibility for determining the adequacy of any thermal or system design
remains solely with the reader. Intel makes no warranties or representations that
merely following the instructions presented in this document will result in a system
with adequate thermal performance.

CAUTION

Ensure that the ambient temperature does not exceed the board’s maximum operating
temperature. Failure to do so could cause components to exceed their maximum case
temperature and malfunction. For information about the maximum operating
temperature, see the environmental specifications in the Intel Desktop Board Technical
Product Specification.

CAUTION

The board is designed to be passively cooled on a properly ventilated chassis. Chassis
venting locations are recommended over the processor, voltage regulator, and system
memory areas for maximum heat dissipation effectiveness.

Ensure that proper airflow is maintained around the processor, processor voltage
regulator circuit, and the DIMM. Failure to do so may result in damage to these
components.

CAUTION

A thermal rating of 85 oC is required for the DIMMs used on this board.

24

Installing and Replacing Desktop Board Components

Installation Precautions

When you install and test the Intel Desktop Board, observe all warnings and cautions
in the installation instructions.

To avoid injury, be careful of:

• Sharp pins on connectors or headers

• Sharp pins on printed circuit assemblies

• Rough edges and sharp corners on the chassis

• Hot components (such as voltage regulators and heat sinks)

• Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to
qualified technical personnel.

Prevent Power Supply Overload

Do not overload the power supply output. To avoid overloading the power supply,
make sure that the calculated total current loads of all the modules within the
computer is less than the output current rating of the power supply.

Observe Safety and Regulatory Requirements

Read and adhere to the instructions in this section and the instructions supplied with
the chassis and associated modules. If you do not follow these instructions and the
instructions provided by chassis and module suppliers, you increase safety risk and the
possibility of noncompliance with regional laws and regulations.

Refer to Appendix B for safety and regulatory requirements.

25

Intel Desktop Board D510MO Product Guide

Installing the I/O Shield

The Desktop Board comes with an I/O shield. When installed in the chassis, the shield
blocks radio frequency transmissions, protects internal components from dust and
foreign objects, and promotes correct airflow within the chassis.

Install the I/O shield before installing the Desktop Board in the chassis. Place the
shield inside the chassis as shown in Figure 5. Press the shield into place so that it fits
t

ghtly and securely. If the shield does not fit, obtain a properly-sized shield from the

i

chassis supplier.

Figure 5. Installing the I/O Shield

26

Installing and Replacing Desktop Board Components

Installing and Removing the Desktop Board

CAUTION

Only qualified technical personnel should do this procedure. Disconnect the computer
from its power source before performing the procedures described here. Failure to
disconnect the power before you open the computer can result in personal injury or
equipment damage.

Refer to your chassis manual for instructions on installing and removing the Desktop
Board.

Figure 6 shows the location of the mounting s
D510MO.

crew holes for Intel Desktop Board

Figure 6. Intel Desktop Board D510MO Mounting Screw Holes

Installing and Removing Memory

NOTE

To be fully compliant with all applicable Intel SDRAM memory specifications, the
boards require DIMMs that support the Serial Presence Detect (SPD) data structure.

The Desktop Board has two 240-pin DDR2 DIMM sockets.

27

Intel Desktop Board D510MO Product Guide

Installing DIMMs

To make sure you have the correct DIMM, place it on the illustration in Figure 7
showing the DDR2 DIMM. All the notches should match the DDR2 DIMM.

28

Figure 7. Use DDR2 DIMMs

Installing and Replacing Desktop Board Components

1. Observe the precautions in "Before You Begin" on page 23.

2. Turn off all peripheral devices connected to the computer. Turn off the computer
and disconnect the AC power cord.

3. Remove the computer’s cover and locate the DIMM socket (see Figure 8).

Figure 8. Installing a DIMM

4. Make sure the clips at either end of the DIMM socket are pushed outward to the
open position.

5. Position the DIMM above the socket. Align the small notch at the bottom edge of
the DIMM with the key in the socket (see Figure 8).

6. In

sert

the bottom edge of the DIMM into the socket.

7. When the DIMM is inserted, push down on the top edge of the DIMM until the
retaining clips snap into place. Make sure the clips are firmly in place.

8. Replace the computer’s cover and reconnect the AC power cord.

29

Intel Desktop Board D510MO Product Guide

Removing DIMMs

To remove a DIMM, follow these steps:

1. Observe the precautions in "Before You Begin" on page 23.

2. Turn off all peripheral devices connected to the computer.

3. Remove the AC power cord from the computer.

4. Remove the computer’s cover.

5. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops
out of the socket.

6. Hold the DIMM by the edges, lift it away from the socket, and store it in an
anti-static package.

7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM
sockets.

8. Replace the computer’s cover and reconnect the AC power cord.

Turn off the computer.

Connecting SATA Drives

The board has two SATA connectors each supporting one SATA drive. The included
SATA cables support the Serial ATA protocol. For correct cable and drive function:

1. Observe the precautions in "Before You Begin" on page 23.

2. Attach the locking cable end to the

3. Attach the cable end without the lock to the

connector on the board (Figure 9, A).

drive (Figure 9, B).

30

Installing and Replacing Desktop Board Components

Figure 9. Connecting the Serial ATA Cable

31

Intel Desktop Board D510MO Product Guide

Installing a Wireless LAN Card in the PCI
Express Full-Mini Card Slot

A wireless LAN card can be installed in the Desktop Board’s PCI Express Full-Mini Card
slot.

To install a wireless LAN card on the Desktop Board, see Figure 10 and follow these
steps:

1. Observe the precautions in "Before You Begin" on page 23.

2. Locate the

3. Insert the wireless LAN card into the PCI Express Mini Card connector (Figure 10,
A) at

4. Align the mounting holes (Figure 10, B) and snap the card in place.

5. Attach yo
wireless LAN card as

NOTE

External antennas can be connected through the I/O shield by removing any or all of
the cut-outs above the back panel I/O section.

PCI Express Full-Mini Card slot.

a slightly upward angle.

ur system’s

antenna wires to the connectors (Figure 10, C) on the

shown.

Figure 10. Installing a Wireless LAN Card

32

Installing and Replacing Desktop Board Components

Installing an Intel® Z-U130 USB Solid-State
Drive (or Compatible Device)

An Intel Z-U130 USB Solid-State Drive (or compatible device) can be installed on the
Desktop Board by using the onboard USB 2.0 header indicated in Figure 1, DD. This
header provides support for the solid state

To install an Intel Z-U130 USB Solid-State Drive (or compatible device) on the Desktop
Board, follow these steps:

1. Observe the precautions in "Before You Begin" on page 23.

2. Ali

gn the connector (Figure 11, A) on the bottom of the solid state drive with the
USB 2.
correctly when the solid state drive is oriented as shown in Figure 11.

0 header on the Desktop Board. The connectors are keyed and will mate

drive.

Figure 11. Installing an Intel Z-U130 USB Solid-State Drive

33

(or Compatible Device)

Intel Desktop Board D510MO Product Guide

Connecting to the Internal Headers

Before connecting cables to the internal headers, observe the precautions in "Before
You Begin" on page 23. Figure 12 shows the location of the board’s in

ternal headers.

34

Figure 12. Internal Headers

Installing and Replacing Desktop Board Components

Connecting the Front Panel Audio Header

Figure 12, A shows the location of the front panel audio header. The front panel audio
header can be used for both Intel HD Audio and AC ‘97 Audio.

Table 6 shows the pin assignments fo

r the Intel HD Audio and Table 7 shows the pin

assignments for AC ‘97 Audio.

Table 6. Front Panel Audio Header for Intel HD Audio

Pin Signal Name Pin Signal Name

1 [Port 1] Left channel 2 Ground
3 [Port 1] Right channel 4 PRESENCE# (Dongle present)
5 [Port 2] Right channel 6 [Port 1] SENSE_RETURN
7 SENSE_SEND (Jack detection) 8 Key (no pin)
9 [Port 2] Left channel 10 [Port 2] SENSE_RETURN

Table 7. Front Panel Audio Header for AC ‘97 Audio

Pin Signal Name Pin Signal Name

1 MIC 2 AUD_GND
3 MIC_BIAS 4 AUD_GND
5 FP_OUT_R 6 FP_RETURN_R
7 AUD_5V 8 KEY (no pin)
9 FP_OUT_L 10 FP_RETURN_L

35

Intel Desktop Board D510MO Product Guide

Connecting to the S/PDIF Header

Before connecting to the S/PDIF connector, observe the precautions in "Before You
Begin" on page 23. See Figure 12, B on page 34 for the location of the S/PDIF header.

Table 8 shows the pin assignments for t

he S/PDIF header.

Table 8. S/PDIF Header

Pin Signal Name

1 Ground
2 S/PDIF out
3 VCC (5V)

Connecting to the Serial Headers

Before connecting to the serial headers, observe the precautions in "Before You Begin"
on page 23. See Figure 12, C on page 34 for the location of the serial headers.

Table 9 shows the pin assignments for the seri

Table 9. Serial Port Headers (COM 1 and COM 2)

Pin Signal Name Pin Signal Name

1 DCD (Data Carrier Detect) 2 RXD# (Receive Data)
3 TXD# (Transmit Data) 4 DTR (Data Terminal Ready)
5 Ground 6 DSR (Data Set Ready)
7 RTS (Request To Send) 8 CTS (Clear To Send)
9 RI (Ring Indicator) 10 Key (no pin)

al headers.

Connecting to the Parallel Port Header

Before connecting to the parallel port header, observe the precautions in "Before You
Begin" on page 23. See Figure 12, D on page 34 for the location of the parallel port
header.

Table 10 shows the pin assignments for the parallel port header.

Table 10.

Pin Standard Signal Name ECP Signal Name EPP Signal Name

1 STROBE# STROBE# WRITE#
2 AUTOFD# AUTOFD#, HOSACK DATASTB#
3 PD0 PD0 PD0
4 FAULT# FAULT#, PERIPHREQST# FAULT#
5 PD1 PD1 PD1
6 INT# INT#, REVERSERQST# RESET#
7 PD2 PD2 PD2
8 SLCTIN# SLCTIN# ADDRSTB#

Parallel Port Header

36

Installing and Replacing Desktop Board Components

Pin Standard Signal Name ECP Signal Name EPP Signal Name

9 PD3 PD3 PD3
10 GROUND GROUND GROUND
11 PD4 PD4 PD4
12 GROUND GROUND GROUND
13 PD5 PD5 PD5
14 GROUND GROUND GROUND
15 PD6 PD6 PD6
16 GROUND GROUND GROUND
17 PD7 PD7 PD7
18 GROUND GROUND GROUND
19 ACK# ACK# INTR
20 GROUND GROUND GROUND
21 BUSY BUSY#, PERIPHACK WAIT#
22 GROUND GROUND GROUND
23 PERROR PE, ACKREVERSE# PE
24 GROUND GROUND GROUND
25 SELECT SELECT SELECT
26 KEY (no pin) KEY (no pin) KEY (no pin)

Connecting to the Front Panel Wireless Activity LED
Header

Before connecting to the front panel wireless activity LED header, observe the
precautions in "Before You Begin" on page 23. See Figure 12, E on page 34 for the
lo

cation of the front panel wireless activity LED header.

Table 11 shows the pin assignments for the fr

Table 11. Front Panel Wireless Activity LED Header

Pin Signal Name

1 LED (+)
2 Ground

ont panel wireless activity LED header.

37

Intel Desktop Board D510MO Product Guide

Connecting to the Front Panel Header

Before connecting to the front panel header, observe the precautions in "Before You
Begin" on page 23. See Figure 12, F on page 34 for the location of the front panel
header.

Table 12 shows the pin assignments for th

Table 12. Front Panel Header Signal Names

Pin Signal In/Out Description Pin Signal In/Out Description

Hard Drive Activity LED Power LED

1 HD_PWR Out

3 HDA# Out

Reset Switch On/Off Switch

5 Ground Ground 6 SWITCH_ON# In Power switch
7 FP_RESET# In Reset switch 8 Ground Ground

Power Not Connected

9 +5 V Power 10 N/C No pin

Hard disk LED pull­up (330 Ω) to +5 V

Hard disk active
LED

e front panel header.

2 HDR_BLNK_GRN Out

4 HDR_BLNK_YEL Out

Front panel
green LED

Front panel
yellow LED

Connecting to the Front Panel USB 2.0 Headers

Before connecting to the USB 2.0 headers, observe the precautions in "Before You
Begin" on page 23. See Figure 12, G and H on page 34 for the location of the USB 2.0
headers. Table 13 and Table 14 show the pin assignments for the

The brown
header (Fig

USB header (Figure 12, G) supports a single USB port while the black USB

ure 12, H) supports two USB ports. The single USB port he
to support a Flash Memory Drive such as the Intel Z-U130 USB Solid-State Drive (or
compatible device). Refer to Installing an Intel

®

Z-U130 USB Solid-State Drive (or

Compatible Device) on page 33 for more information.

Table 13.

Pin Signal Name Pin Signal Name

1
3
5
7
9

Front Panel USB Header

+5 VDC
D-
D+
Ground
KEY (no pin)

2
4
6
8
10

+5 VDC
D-
D+
Ground
No Connect

headers.

ader is designed

38

Installing and Replacing Desktop Board Components

Table 14. Front Panel USB Header with Intel Z-U130 USB Solid-State Drive

(or Compatible Device) Support

Pin Signal Name Pin Signal Name

1
3
5
7
9

+5 VDC
D-
D+
Ground
KEY (no pin)

2
4
6
8
10

No Connect
No Connect
No Connect
No Connect
LED#

Connecting a Chassis Fan

Figure 13 shows the location of the chassis fan header. Connect the chassis fan cable
to this header.

Figure 13. Location of the Chassis Fan Header

39

Intel Desktop Board D510MO Product Guide

Connecting the Power Supply Cable

CAUTION

Failure to use an appropriate power supply to the Desktop Board may result in damage
to the board or the system may not function properly.

Figure 14 shows the location of the power connector.

Figure 14. Connecting a Power Supply Cable

1. Observe the precautions in "Before You Begin" on page 23.

2. Connect the main power supply cable (2 x 12) to the 2 x 12 connector (Figure 14).

40

Installing and Replacing Desktop Board Components

Setting the BIOS Configuration Jumper

NOTE

Always turn off the power and unplug the power cord from the computer before
changing a jumper. Moving the jumper with the power on may result in unreliable
computer operation.

Figure 15 shows the location of the Desktop Board’s BIOS configurati

on jumper block.

Figure 15. BIOS Configuration Jumper Block

The three-pin BIOS jumper block enables board operating modes. Table 15 shows the
jumper settings for each of the available modes.

41

Intel Desktop Board D510MO Product Guide

Figure 15 shows the location of the Desktop Board’s BIOS configuration jumper block.

Table 15. Jumper Settings for the BIOS Setup Program Modes

Jumper
Setting

Mode

Normal (default) (1-2) The BIOS uses the current configuration and

Configure (2-3) After the Power-On Self-Test (POST) runs, the

Recovery (None) The BIOS recovers data from a recovery diskette

Description

passwords for booting.

BIOS displays the Maintenance Menu. Use this
menu to clear passwords.

in the event of a failed BIOS update.

Clearing Passwords

This procedure assumes that the board is installed in the computer and the
configuration jumper is set to normal mode.

1. Observe the precautions in "Before You Begin" on page 23.

2. Turn off all peripheral devices connected to the computer.

Disconnect the computer’s power cord from the AC power source (wall outlet or
power adapter).

3. Remove the computer cover.

4. Find the configuration jumper block (see Figure 15, B).

5. Place the jumper on pins 2-3 as shown

below.

Turn off the computer.

6. Replace the cover, plug in the computer, turn on the computer, and allow it to

boot.

7. The computer starts the Setup program. Setup displays the Maintenance menu.

8. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a

pop-up screen requesting that you confirm clearing the password. Select Yes and
press <Enter>. Setup displays the maintenance menu again.

9. Press <F10> to save the current values and exit Setup.

42

Installing and Replacing Desktop Board Components

10. Turn off the computer. Disconnect the computer’s power cord from the AC power

source.

11. Remove the computer cover.

12. To restore normal operation, place the jumper on pins 1-2 as shown below.

13. Replace the cover, plug in the computer, and turn on the computer.

Replacing the Battery

A coin-cell battery powers the Desktop Board’s real-time clock and CMOS memory.
When the computer is not plugged into a wall socket, the battery has an estimated life
of three years. When the computer is plugged in, the standby current from the power
supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at
25 ºC with 3.3 VSB applied.

When the voltage drops below a certain level, the BIOS Setup program settings stored
in CMOS RAM (for example, the date and time) might not be accurate. Replace the
battery with an equivalent one. Figure 16 on page 47 shows the location of the
battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where
possible. Disposal of used batteries must be in accordance with local environmental regulations.

PRÉCAUTION

Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent
être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les
réglementations locales en vigueur en matière de protection de l'environnement.

FORHOLDSREGEL

Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges.
Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning.

OBS!

Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til
gjeldende miljølovgivning.

VIKTIGT!

Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala
miljövårdsbestämmelserna.

43

Intel Desktop Board D510MO Product Guide

VARO

Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt

paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti.

VORSICHT

Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben
oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie ver­brauchte Batterien den Anweisungen des Herstellers entsprechend.

AVVERTIMENTO

Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali
o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del
produttore.

PRECAUCIÓN

Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del
mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga
igualmente las instrucciones del fabricante.

WAARSCHUWING

Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen
moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de
plaatselijke milieuwetgeving.

ATENÇÃO

Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser
recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as
regulamentações ambientais da região.

AŚCIAROŽZNAŚĆ

Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па
магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым
заканадаўствам па экалогіі.

UPOZORNÌNÍ

V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být
recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí.

Προσοχή

Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου τύπου. Οι
μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιμοποιημένων
μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς κανονισμούς.

44

Installing and Replacing Desktop Board Components

VIGYÁZAT

Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell
hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni.

AWAS

Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula
jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan.

OSTRZEŻENIE

Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie
należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska.

PRECAUŢIE

Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate,
dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia
mediului.

ВНИМАНИЕ

При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи
должны быть утилизированы по возможности. Утилизация батарей должна проводится по
правилам, соответствующим местным требованиям.

UPOZORNENIE

Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu.
Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade
s miestnymi predpismi na ochranu životného prostredia.

POZOR

Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.
Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi.

.

UYARI

Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir.
Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

45

Intel Desktop Board D510MO Product Guide

OСТОРОГА

Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути
виконана згідно місцевих норм, що регулюють охорону довкілля.

46

Installing and Replacing Desktop Board Components

1. Observe the precautions in "Before You Begin" (see page 23).

2. Turn off all peripheral devices connected to the computer. Disconnect the

computer’s power cord from the AC power source (wall outlet or power adapter).

3. Remove the computer cover.

4. Locate the battery on the board (see Figure 16).

5. P

u

sh the battery retention clip aside and remove the battery from the connector as

shown in Figure 16. Note the orientation of the “+” and “-” on the battery.

6. Instal

the new battery in the connector, making sure to orient the “+” and “-”

l

correctly.

7. Replace the computer cover.

47

Figure 16. Removing the Battery

Intel Desktop Board D510MO Product Guide

48

3 Updating the BIOS

The BIOS Setup program can be used to view and change the BIOS settings for the
computer. You can access the BIOS Setup program by pressing the <F2> key after
the Power-On Self-Test (POST) memory test begins and before the operating system
boot begins.

This chapter tells you how to update the BIOS by either using the Intel Express BIOS
Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an
update fails.

Updating the BIOS with the Intel® Express
BIOS Update Utility

With the Intel Express BIOS Update utility you can update the system BIOS while in
the Windows environment. The BIOS file is included in an automated update utility
that combines the functionality of the Intel
of use of Windows-based installation wizards.

®

Flash Memory Update Utility and the ease

To update the BIOS with the Intel Express BIOS Update utility:

1. Go to http://support.intel.com/support/motherboards/des

2. Navigate to the Intel Desktop Board D510MO page, click “[view] Latest BIOS

updates,” and select the Express BIOS Update utility file.

3. Download the file to your hard drive. (You can also save this file to a removable

USB device. This is useful if you are updating the BIOS for multiple identical
systems.)

4. Close all other applications. This step is required. Your system will be rebooted at

the last Express BIOS Update window.

5. Double-click the executable file from the location on your hard drive where it was

saved. This runs the update program.

6. Follow the instructions provided in the dialog boxes to complete the BIOS update.

ktop/.

49

Intel Desktop Board D510MO Product Guide

Updating the BIOS with the Iflash Memory
Update Utility

You can use the information in this section to update the BIOS using the Iflash
Memory Update Utility.

Obtaining the BIOS Update File

You can update to a new version of the BIOS by using the Iflash BIOS update file.
The Iflash BIOS update file is a compressed file that contains the files you need to

update the BIOS. The Iflash BIOS update file contains:

• New BIOS file

• Intel Flash Memory Update Utility

You can obtain either of these files through your computer supplier or by navigating to
the Intel Desktop Board D510MO page at

http://support.intel.com/support/motherboards/desktop

Navigate to the Intel Desktop D510MO page, click “[view] Latest BIOS updates,” and
select the Iflash BIOS Update utility file.

.

CAUTION

Do not interrupt the process or the system may not function properly.

Using the Iflash Memory Update Utility

With the Iflash Memory update utility you can update the system BIOS from a
bootable USB flash drive or other bootable USB media. The Iflash BIOS update files
can be extracted locally to your hard drive and copied to a bootable USB flash drive or
other bootable USB media.

NOTE

Review the instructions distributed with the update utility before attempting a BIOS
update.

CAUTION

Do not interrupt the process or the system may not function properly.

1. Uncompress the BIOS update file and copy the .BIO file and IFLASH.EXE to a

bootable USB flash drive or other bootable USB media.

2. Configure the BIOS or use the F10 key option during POST to boot to the USB

device.

3. Manually run the IFLASH.EXE file from the USB device and manually update the

BIOS.

50

Updating the BIOS

Recovering the BIOS

It is unlikely that anything will interrupt a BIOS update; however, if an interruption
occurs, the BIOS could be damaged. Table 16 lists the drives and media types that
can and cannot be
to be bootable.

Table 16. Acceptable Drives/Media Types for BIOS Recovery

Media Type Can be Used for BIOS Recovery?

CD-ROM drive connected to the SATA interface Yes
USB removable drive (a USB Flash Drive, for example) Yes
USB diskette drive (with a 1.44 MB diskette) No
USB hard disk drive No

NOTE

For more information about BIOS update and recovery, go to

http://support.intel.com/support/motherboards/desktop/

used for BIOS recovery. The BIOS recovery media does not have

sb/CS-022312.htm.

51

Intel Desktop Board D510MO Product Guide

52

A Board Status and Error Messages

This appendix describes status and error messages generated by the Desktop Board’s
BIOS. The BIOS indicates these error messages with front-panel Power LED blink
codes, speaker beep codes, and by displaying text on the video monitor.

BIOS Beep Codes

The BIOS uses audible beep codes to signal status messages and error messages
indicating recoverable errors that occur during the POST. The beep codes are listed in
Table 17. These beep codes can be heard t
line out audio jack (see Figure 2, B on page 15).

rough a speaker attached to the board’s

h

Table 17.

Type Pattern Frequency

F2 Setup/F10 Boot
Menu Prompt

Video error On-off (1.0 second each) two times, then a

Memory error On-off (1.0 second each) three times, then

Thermal trip warning Alternate high and low beeps (1.0 second

BIOS Beep Codes

One 0.5-second beep when the BIOS is
ready to accept keyboard input

2.5-second pause (off); the entire pattern
repeats (beeps and pause) once and the
BIOS will continue to boot.

a 2.5-second pause (off); the entire pattern
repeats (beeps and pause) until the system
is powered off.

each) for eight beeps, followed by system
shut down.

932 Hz

932 Hz
When no VGA option ROM
is found.

932 Hz

High beep 2000 Hz
Low beep 1500 Hz

53

Intel Desktop Board D510MO Product Guide

BIOS Front-panel Power LED Blink Codes

The BIOS also blinks the front-panel power LED to signal status messages and error
messages indicating certain recoverable errors that occur during the POST. The blink
codes are listed in Table 18.

Table 18.

Type Pattern Note

BIOS update in
progress

Video error On-off (1.0 second each) two times, then a

Memory error On-off (1.0 second each) three times, then

Thermal trip warning Each beep will be accompanied by the

BIOS Front-panel Power LED Blink Codes

Off when the update begins, then on for

0.5 second, and then off for 0.5 second.
The pattern repeats until the BIOS update
is complete.

2.5-second pause (off); the entire pattern
repeats (blinks and pause) until the system
is powered off.

a 2.5-second pause (off); the entire pattern
repeats (blinks and pause) until the system
is powered off.

following blink pattern: 0.25 second on,

0.25 second off, 0.25 second on,

0.25 second off. This results in a total of
16 blinks followed by system shut down.

When no VGA option ROM
is found.

POST Error Messages

The BIOS also displays error messages on the video monitor when certain recoverable
errors occur during the POST. Table 19 lists the error messages with a brief
description of each.

Table 19.

Error Message Explanation

CMOS Battery Low The battery may be losing power.
CMOS Checksum Bad The CMOS checksum is incorrect. The CMOS memory

Memory Size Decreased Memory size has decreased since the last boot. If no

No Boot Device Available System did not find a device to boot.

POST Error Messages

54

may have been corrupted. Run Setup to reset values.

memory was removed, then memory may be bad.

B Regulatory Compliance

This appendix contains the following regulatory compliance information for Intel
Desktop Board D510MO:

• Safety standards

• European Union Declaration of Conformity statement

• Product Ecology statements

• Electromagnetic Compatibility (EMC) regulations

• Product certifications

Safety Standards

Intel Desktop Board D510MO complies with the safety standards stated in Table 20
when correctly installed in a compatible host system.

Table 20. Safety Standards

Regulation Title

CSA/UL 60950-1, First
Edition

EN 60950-1:2006, Second
Edition

IEC 60950-1:2005, Second
Edition

Information Technology Equipment – Safety - Part 1: General
Requirements (USA and Canada)

Information Technology Equipment – Safety - Part 1: General
Requirements (European Union)

Information Technology Equipment – Safety - Part 1: General
Requirements (International)

Place Battery Marking

There is insufficient space on this Desktop Board to provide instructions for replacing
and disposing of the Lithium ion coin cell battery. For system safety certification, the
statement below or an equivalent statement is required to be permanently and legibly
marked on the chassis near the battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

A suitable caution label is included with Intel Desktop Board D510MO.
For information about replacing the battery, go to page 43.

55

Intel Desktop Board D510MO Product Guide

European Union Declaration of Conformity
Statement

We, Intel Corporation, declare under our sole responsibility that the product Intel®
Desktop Board D510MO is in conformity with all applicable essential requirements
necessary for CE marking, following the provisions of the European Council Directives
2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).

The product is properly CE marked demonstrating this conformity and is for
distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC and
2006/95/EC.

Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a
2006/95/EC.

Dansk Dette produkt er i overensstemmelse med det europæiske direktiv
2004/108/EC & 2006/95/EC.

Dutch Dit product is in navolging van de bepalingen van Europees Directief
2004/108/EC & 2006/95/EC.

Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC
kehtestatud nõuetele.

Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.
Français Ce produit est conforme aux exigences de la Directive Européenne

2004/108/EC & 2006/95/EC.
Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie

2004/108/EC & 2006/95/EC.
Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών

2004/108/EC και 2006/95/EC.
Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv

előírásainak.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer

2004/108/EC & 2006/95/EC.
Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC &

2006/95/EC.
Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC

noteikumiem.
Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC

nuostatas.
Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej

2004/108/EC u 2006/95/EC.

56

Regulatory Compliance

Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
2004/108/EC & 2006/95/EC.

Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC i 2006/95/EC.

Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC
& 2006/95/EC.

Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC &
2006/95/EC.

Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív
2004/108/EC a 2006/95/EC.

Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in
2006/95/EC.

Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC &
2006/95/EC.

Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.

Product Ecology Statements

The following information is provided to address worldwide product ecology concerns
and regulations.

Recycling Considerations

As part of its commitment to environmental responsibility, Intel has implemented the

®

Intel
to return used products to selected locations for proper recycling.

Please consult http://www.intel.com/intel/other/ehs/produ
for the details of this program, including the scope of covered products, available
locations, shipping instructions, terms and conditions, etc.

中文

作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program
（英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作恰
当的重复使用处理。

请参考http://www.intel.com/intel/other/ehs
了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。

Product Recycling Program to allow retail consumers of Intel’s branded products

ct_ecology

oduct_ecology

/pr

57

Intel Desktop Board D510MO Product Guide

Deutsch

Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel
Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel
Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für
ordnungsgemäßes Recycling zurückzugeben.

Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte,
verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der

http://www.intel.com/intel/other/ehs/product_ecology

Español

Como parte de su compromiso de responsabilidad medioambiental, Intel ha
implantado el programa de reciclaje de productos Intel, que permite que los
consumidores al detalle de los productos Intel devuelvan los productos usados en los
lugares seleccionados para su correspondiente reciclado.

Consulte la http://www.intel.com/intel/other/ehs/product_ecology
para ver los detalles del programa, que incluye los productos que abarca, los lugares
disponibles, instrucciones de envío, términos y condiciones, etc.

Français

Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis
en œuvre le programme Intel Product Recycling Program (Programme de recyclage
des produits Intel) pour permettre aux consommateurs de produits Intel de recycler
les produits usés en les retournant à des adresses spécifiées.

Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology

pour en
savoir plus sur ce programme, à savoir les produits concernés, les adresses
disponibles, les instructions d'expédition, les conditions générales, etc.

日本語

インテルでは、環境保護活動の一環として、使い終えたインテル
ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル
プログラムを発足させました。

対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://www.intel.com/in

tel/other/ehs/product_ecology （英語）をご覧ください。

Malay

Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran,
Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan
pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke
lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.

Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology

untuk mendapatkan
butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi
tersedia, arahan penghantaran, terma & syarat, dsb.

58

Regulatory Compliance

Portuguese

Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o
Programa de Reciclagem de Produtos para que os consumidores finais possam enviar
produtos Intel usados para locais selecionados, onde esses produtos são reciclados de
maneira adequada.

Consulte o site http://www.intel.com/intel/other/ehs/product_ecology

(em Inglês) para

obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os
locais disponíveis, as instruções de envio, os termos e condições, etc.

Russian

В качестве части своих обязательств к окружающей среде, в Intel создана
программа утилизации продукции Intel (Product Recycling Program) для
предоставления конечным пользователям марок продукции Intel возможности
возврата используемой продукции в специализированные пункты для должной
утилизации.

Пожалуйста, обратитесь на веб-сайт

http://www.intel.com/intel/other/ehs/product_ecology

за информацией об этой

программе, принимаемых продуктах, местах приема, инструкциях об отправке,
положениях и условиях и т.д.

Türkçe

Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin
Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri
dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya
koymuştur.

Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve
şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen

http://www.intel.com/intel/other/ehs/product_ecology

web sayfasına gidin.

59

Intel Desktop Board D510MO Product Guide

Lead-free 2LI/Pb-free 2LI Board

The electronics industry is transitioning to European Union (EU) Restriction of
Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the
use of six materials. One of these restricted materials is lead. Lead is the most
common and problematic of the RoHS restricted materials.

There are exemptions in RoHS that allow the use of lead in some very limited locations
in electronic products. Maximum lead concentration values have been established for
RoHS-compliant electronic products that allow up to 1000 ppm of lead.

Lead-free/Pb-free is a nickname that is often used (or misused) for RoHS-compliant
products. In this case, the term "Lead-free/Pb-free" means that lead has been
removed where required by the RoHS legislation but still may exist as an impurity
below 1000 ppm.

The term "Lead-free 2LI/Pb-free 2LI" means lead-free second level interconnect (2LI).
The balls, leads, or pads used to connect the component to a printed circuit board are
lead-free, but the first level interconnect (FLI) is not lead-free. The use of lead in the
FLI is acceptable because of the RoHS "flip chip" or "die bump" interconnect
exemption.

Intel Desktop Board D510MO is a lead-free second level interconnect product.
Table 21 shows the lead-free second level interconnect
board and a

ccompanying collateral. These marks are based on JEDEC standard

marks as they appear on the

J-STD-609, “Marking and Labeling of Components, PCBs and PCBAs to Identify Lead,
Lead Free and Other Attributes.”

For more information concerning Intel’s lead-free initiatives, refer to

http://www.intel.com/technology/silicon/leadfree.htm

.

Table 21. Lead-Free Second Level Interconnect Marks

Description Mark

This symbol is used to identify
electrical and electronic
assemblies and components in
which the Pb concentration
level in the Desktop Board
substrate and the solder
connections from the board to
the components (second-level
interconnect) is not greater
than 0.1% by weight
(1000 ppm).

or

or

60

Regulatory Compliance

Restriction of Hazardous Substances (RoHS)

European Union RoHS

EU RoHS Directive 2002/95/EC restricts the use of the following six materials in
various types of electronic and electrical equipment:

• Lead

• Mercury

• Cadmium

• Hexavalent chromium

• Polybrominated biphenyls (PBB)

• Polybrominated diphenyl ether (PBDE)

The maximum concentrations allowed are 0.1% or 1000 ppm (except for cadmium,
which is limited to 0.01% or 100 ppm) by weight of homogeneous material.

Intel Desktop Board D510MO complies with these restrictions.

China RoHS

“China RoHS” is the term used by industry generally to describe legislation
implemented by the Ministry of Information Industry (MII) in the People's Republic of
China for the control of pollution by electronic information products (EIP). The official
title of the China RoHS regulation is “Management Methods for Controlling Pollution by
Electronic Information Products.”

China RoHS bans the same substances and has the same limits as EU RoHS.
However, the China RoHS regulation requires specific product marking and a self­declaration of the controlled substances contained in each product.

Intel Desktop Board D510MO is a China RoHS-compliant product.
The required China RoHS mark indicates the product’s Environmental Friendly Usage

Period (EFUP). The EFUP is defined as the number of years for which listed controlled
substances will not leak or chemically deteriorate while in the product. The EFUP for
Intel Desktop Boards has been determined to be 10 years.

The EFUP for Intel Desktop Board D510MO is shown in Table 22.

Table 22.

Description Mark

This is an example of the
symbol used on Intel Desktop
Boards and associated
collateral. The color of the
mark may vary depending
upon the application. The
Environmental Friendly Usage
Period (EFUP) for Intel
Desktop Boards has been
determined to be 10 years.

China RoHS Environmentally Friendly Use Period Mark

61

Intel Desktop Board D510MO Product Guide

The China MII also stipulates that a material Self Declaration Table (SDT) must be
included in a product’s user documentation. The SDT for Intel Desktop Board D510MO
is shown in Figure 17.

Figure 17. Intel Desktop Board D510MO China RoHS Material

62

Self Declaration Table

Regulatory Compliance

EMC Regulations

Intel Desktop Board D510MO complies with the EMC regulations stated in Table 23
when correctly installed in a compatible host system.

Table 23. EMC Regulations

Regulation (Class B) Title

FCC 47 CFR Part 15,
Subpart B

ICES-003 Issue 4 Interference-Causing Equipment Standard, Digital Apparatus.

EN55022:2006 Limits and methods of measurement of Radio Interference

EN55024:1998 Information Technology Equipment – Immunity Characteristics

EN55022:2006 Australian Communications Authority, Standard for

CISPR 22:2005
+A1:2005 +A2:2006

CISPR 24:1997
+A1:2001 +A2:2002

VCCI V-3/2007.04,
V-4/2007.04

KN-22, KN-24 Korean Communications Commission – Framework Act on

CNS 13438:2006 Bureau of Standards, Metrology and Inspection. (Taiwan)

Japanese Kanji statement translation: This is a Class B product based on the standard
of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.

Title 47 of the Code of Federal Regulations, Part 15, Subpart B,
Radio Frequency Devices. (USA)

(Canada)

Characteristics of Information Technology Equipment. (European
Union)

Limits and methods of measurement. (European Union)

Electromagnetic Compatibility. (Australia and New Zealand)
Limits and methods of measurement of Radio Disturbance

Characteristics of Information Technology Equipment.
(International)

Information Technology Equipment – Immunity Characteristics –
Limits and Methods of Measurement. (International)

Voluntary Control for Interference by Information Technology
Equipment (Japan)

Telecommunications and Radio Waves Act. (South Korea).

63

Intel Desktop Board D510MO Product Guide

Korean Class B statement translation: This is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential
environments and other non-residential environments.

Ensure Electromagnetic Compatibility (EMC)
Compliance

Before computer integration, make sure that the power supply and other modules or
peripherals, as applicable, have passed Class B EMC testing and are marked
accordingly.

Pay close attention to the following when reading the installation instructions for the
host chassis, power supply, and other modules:

• Product certifications or lack of certifications

• External I/O cable shielding and filtering

• Mounting, grounding, and bonding requirements

• Keying connectors when mating the wrong connectors could be hazardous

If the power supply and other modules or peripherals, as applicable, are not Class B
EMC compliant before integration, then EMC testing may be required on a
representative sample of the newly completed computer.

64

Regulatory Compliance

Product Certifications

Board-Level Certification Markings

Intel Desktop Board D510MO has the product certification markings shown in
Table 24.

Table 24.

Description Mark

UL joint US/Canada Recognized Component mark. Includes adjacent
UL file number for Intel Desktop Boards: E210882.

FCC Declaration of Conformity logo mark for Class B equipment.
Includes Intel name and D510MO model designation.

CE mark. Declaring compliance to European Union (EU) EMC
directive and Low Voltage directive.

Australian Communications Authority (ACA) and New Zealand Radio
Spectrum Management (NZ RSM) C-tick mark. Includes adjacent
Intel supplier code number, N-232.

Japan VCCI (Voluntary Control Council for Interference) mark.

S. Korea KCC (Korean Communications Commission) mark. Includes
adjacent KCC certification number: CPU-D510MO (B).

Product Certification Markings

Taiwan BSMI (Bureau of Standards, Metrology and Inspections)
mark. Includes adjacent Intel company number, D33025.

Printed wiring board manufacturer’s recognition mark. Consists of a
unique UL recognized manufacturer’s logo, along with a flammability
rating (solder side).

V-0

65

Intel Desktop Board D510MO Product Guide

Chassis and Component Certifications

Ensure that the chassis and certain components; such as the power supply, peripheral
drives, wiring, and cables; are components certified for the country or market where
used. Agency certification marks on the product are proof of certification. Typical
product certifications include:

In Europe
The CE marking signifies compliance with all applicable European requirements. If the
chassis and other components are not properly CE marked, a supplier’s Declaration of
Conformity statement to the European EMC directive and Low Voltage directive (as
applicable), should be obtained. Additionally, other directives, such as the Radio and
Telecommunications Terminal Equipment (R&TTE) directive may also apply depending
on product features.

In the United States
A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL,
CSA, or ETL signifies compliance with safety requirements. Wiring and cables must
also be UL listed or recognized and suitable for the intended use. The FCC Class B
logo for home or office use signifies compliance with electromagnetic interference
(EMI) requirements.

In Canada
A nationally recognized certification mark such as CSA or cUL signifies compliance with
safety requirements. The Industry Canada statement at the front of this product guide
demonstrates compliance with Canadian EMC regulations.

66