Intel A2TXOTT User Manual

IMPORTANT SAFETY & REGULATORY INFORMATION

DO NOT DISCARD – DOCUMENT MUST REMAIN WITH PRODUCT

Model: A2TX OTT

This device complies with part 15 and Part 18 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Intel Corporation, 2111 NE 25th Ave, Hillsboro, OR 97124 USA

Modifications made to this device, unless expressly approved by Intel Corporation, may void the user’s
rights to operate this equipment.

Note: This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Exposure and Compatibility with Implantable Cardiac Medical Devices.

Wireless Power devices are designed to meet all applicable RF health and safety regulations prescribed
by individual countries around the world. Through complex testing procedures we have demonstrated to
appropriate country regulators that the RF emissions from our wireless power devices meet the basic
exposure restrictions set forth in ICNIRP or IEEE or similar international RF safety standards. Based on
readily available information, Intel’s wireless power device should not cause interference with any
implantable cardiac device. However because each cardiac device can be different and some may be
affected by low powered RF fields, individuals wearing implantable cardiac devices should not be in
very close proximity ( or direct contact) with the wireless power device. Individuals should discuss any
concerns about the compatibility of their medical device with their physician or medical device
manufacturer.

This charging mat is designed for table top use only. To comply with rf exposure requirements this
charging mat must be placed on a table top when operational.

This is a wireless charging area intended for use with A4WP wireless charging accessories. Near
Field Communication Tags (NFC Tags such as contactless room key cards, transit passes and similar),
DVDs and CDs may be damaged if placed on or near the charging surface.

Page 1 of 3 Wednesday, December 02, 2015

IMPORTANT SAFETY & REGULATORY INFORMATION

DO NOT DISCARD – DOCUMENT MUST REMAIN WITH PRODUCT

OTHER SAFETY NOTICES

Power Supply Hazardous Voltage: AC mains voltages are present within the power supply assembly

No user serviceable parts inside the power supply

Power Connect and Disconnect: The AC power supply cord is the primary disconnect device from mains (AC

power) and used to remove all DC power from the board/system. The socket outlet shall be installed near the
equipment and shall be readily accessible.

.

.

WARNING

RISK OF ELECTRIC SHOCK

Connect only to a properly earth grounded outlet.

Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk.

System Grounding (Earthing): To avoid shock, ensure that the power cord is connected to a properly wired
and grounded receptacle. Ensure that any equipment to which this product will be attached is also connected to
properly wired and grounded receptacles

WARNING

RISK OF ELECTRIC SHOCK

Do not attempt to modify or use the supplied AC power cord if it is not the exact type

and rating required.

Power Cord Requirements: The connector that plugs into the wall outlet must be a grounding-type male plug
designed for use in your region. It must have certification marks showing certification by an agency in your region.
The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13, female
connector. See the following website for more information http://kropla.com/electric2.htm. If the power cord
supplied with the system does not meet requirements for use in your region discard the cord, do not use with
adapters.

Page 2 of 3 Wednesday, December 02, 2015