Waste Xpress Parts List
®
1 Year Full Warranty
F360 -08H-45-10 Rev. 7/08
Ordering Parts
Name Plate
Spec. Location
FOOD WASTE PULPER
FOR SERVICE INFO, CALL 1-800 -845-8345
SE RIAL N UMBER :
X X X X X X X X X X X
VO LTS : 20 8/ 23 0V
1/ 2 HP 3 PH 60 HZ 1725 R PM
U . S. P a t . No . 7 .1 3 7. 5 0 3
14534B
E3 08 976
517L
AM PS : 2.5 /2.0A
MODEL: WX-8
PART NUMB ER 14492B
• Order by part number, not by code number
• Include information from nameplate specication
(see gures at right)
• Complete model number (ex: WX-8)
• Complete serial number (ex: XM0000000 - thru
September 2003)
Order parts from:
• (USA)
InSinkErator
4700 - 21st St.
Racine, WI 53406
• (Within the USA)
Foodservice and Tech Support
800.845.8345
• (Outside the USA)
Foodservice and Tech Support
262.554.5432
SERIES 1
MODEL # SPECIFICATION SERIAL # RANGE
WX-1 115V / 1 Phase
WX-2 208-230V / 3 Phase
WX-3 200V 50/60 / 3 Phase
WX-4 460V / 3 Phase
WX-5 208-230V / 1 Phase
Note: Physical differences exist in the numerous service parts between the models in Series 1 and Series 2 – no
substitutions between series should be carried out unless otherwise specied in the parts tables.
Unit Specications and Identication
MODEL # SPECIFICATION SERIAL # RANGE
WX-8 208-230V / 3 Phase
TD0000000 - XM0000000
0310XXXXXXX - 0704XXXXXXX
WX-9 460V / 3 Phase
SERIES 2
0705XXXXXXX - Higher
2
1
3
5
4
2
1
Plumbing
REPAIRS – WX-1 THRU WX-5
CODE # DESCRIPTION QTY PART #
1 Water Inlet Tube 1 14263
2 Solenoid Valve - WX 1 14264
3 Tubing Assembly - Water Transfer 1 14265
4 Tubing Assembly - Spray Nozzle 1 14266
5 Spray Nozzle 4 14071
REPAIRS – WX-8 AND WX-9
CODE # DESCRIPTION QTY PART #
1 Tube Assembly (Includes 14683) 1 14682
2 Spray Nozzle 4 14683
4
7
6
2
5
3
12
5
10
6
7
9
7
8
4
8
7
11
1
Cabinet
WX-1 TO WX-5
SERIES 1
CODE # DESCRIPTION QTY
1 Discharge Chute 1 14251 14678
2 Handle, Discharge Chute 2 14252 N/A
3 Interlock Assembly 1 14258 14668
4 Inlet/Outlet Kit 1 14256 14679
5 Inlet/Outlet Gasket 1 14255 14681
6 Inlet/Outlet Cap 1 14254 14680
7 Bolt 1/4-20 x 1/2 SS 1 N/A 14698
8 Washer 1 N/A
9 Belt, Cover WX 1 14260 14677
10 Foot - Adjustment 1 14259 14675
11 Motor Cover 1 14261 14676
12 Strain Relief 1 14262 14697
PART #
WX-8 AND WX-9
SERIES 2
PART #
6
8
7
5
9
10
11
4
1
3
2
Cabinet
WX-1 TO WX-5
SERIES 1
CODE # DESCRIPTION QTY
1 Bearing Bracket 1 14655
2 Auger Brush 1 N/A 14426
3 Auger 1 14401
4 Auger Screen 1 14359* 14665
5 Auger Drive Assembly 1 14244 14671
6 Auger Belt 1 14672
7 Auger Pulley 1 14246 14674
8 Motor Pulley 1 N/A 14673
9a Motor Bracket - 1 Phase 1 14249 N/A
9b Motor Bracket - 3 Phase 1 14249A N/A
10 Tension Screw 1 14248 N/A
11a Motor – 115/208-230V / 1 Phase 1 14247 N/A
11b Motor – 208-230/460V / 3 Phase 1 14247A 14666
PART #
WX-8 AND WX-9
SERIES 2
PART #
Electrical Controls
3
4
2
5
1
3 4 5 6 7 81
L1
T1
2 4 6 98
97 95
18
A1 15
16 A2
96
T2 T3 NO A2
ON
OFF
L2 L3 NO A1
2
1
2
The primary difference between a Series 1 and a Series 2 WX is the location of the electrical controls specic to the
pulper that operates the auger, controls the hot water spray cycle and protects the WX from becoming overloaded
should the WX jam during its operation. In the original Series 1 design, a standard CC-101K control and later, the
WX-101 were used to merely start and stop the system, and provide control for the cold water in the system. With
the change to the Series 2 in May of 2007, the WX motor contactor, hot water spray timer and WX overload were
relocated from inside the motor compartment on the back of the WX machine, to a more convenient location inside
of the control center (WX-101A) itself. Servicing the controls should be referenced using the following tables (see
separate spare parts sheet(s) for servicing CC-101K, WX-101 and WX-101A Series Control Centers).
SERIES 1
MODEL # SPECIFICATION CONTROL CENTER
WX-1 115V / 1 Phase CC-101K-1 or WX-101-1
WX-2 208-230V / 3 Phase CC-101K-3 or WX-101-3
WX-3 200V 50/60 / 3 Phase (Export) CC-101K-3 or WX-101-3
WX-4 460V / 3 Phase CC-101K-4 or WX-101-4
WX-5 208-230V / 1 Phase CC-101K-2 or WX-101-2
REPAIRS – WX-1 THRU WX-5
SERIES 2
MODEL # SPECIFICATION CONTROL CENTER
WX-8 208-230V / 3 Phase WX-101A-3
WX-9 460V / 3 Phase WX-101A-4
REPAIRS – WX-6 THRU WX-9
CODE # DESCRIPTION QTY PART #
1 Strain Relief 5 14262
2 Terminal Block 1 14267
3 Hot Water Spray Timer 1 14268
CODE # DESCRIPTION QTY PART #
1 Terminal Block 1 14670
2 Terminal Block Cover 1 14669
3 Terminal Cover Gasket 1 14700
4 Contactor 1 14113
5 Overload - Adj 208-230V 1 14106
Overload - Adj 460V 1 14106A
Overload - Adj 115 V 1 14106B
1.800.845.8345
www.insinkerator.com/foodservice
Note: Items #3–5 for Series 2 machines are located in
WX-101A Control Center. See WX-101A parts sheet #1
F350-07F-45-10 REV 06/07 for details.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
InSinkErator may make improvements and/or changes in the specications
at any time, in its sole discretion, without notice or obligation and further
reserves the right to change or discontinue models.
© 2008 InSinkErator, a division of Emerson Electric Co. All Rights Reserved.
Loading...