InSinkErator Ultra System Owner's Manual

Installation, Care & Use

Instalacion, Cuidado & Uso

Installation, Sion & Utilisation

Owner’s Manual

The Emerson logo is a trademark and a

service mark of Emerson Electric, Co.

InSinkErator is a division

of Emerson Electric, Co.

44062 0407

www.insinkerator.com

Printed in USA ©2007 InSinkErator

Lock

Washer

Hex Nut Deck Plate

Metal

Mounting Plate

UW/UWL

Tank

3/4" Screws (2)

Snap-Connect

Fitting (3 pieces)

Plastic Mounting Gasket

3

HOW TO USE THIS INSTRUCTION MANUAL

Provides a step-by-step narrative describing the installation step, with check boxes that
can be marked as you progress through the installation.

Contains simple illustrations that provide visual instruction to support the narrative.

CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.

These instructions are separated into main sections, indicated by numbers, and subsections,
indicated by capital letters. The manual is setup this way to allow you to take a break at any
point after completing a section or subsection without affecting the installation process.

What you’ll see in the
in

struction manual:

1

2

3

A

■

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

INSTALLING THE FAUCET

Unpack faucet components.
On a firm, flat surface, carefully

straighten the copper tubing.

1

2

An imminently hazardous situation, which,if not avoided,will result in death or serious injury.

A potentially hazardous situation, which, if not avoided, could result in death or serious injury.

A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

3

Equipment You May Need:

Q For your satisfaction and safety,read all instructions, cautions, warnings and dangers before installing

or using this hot water faucet.

Q Make sure that all electrical wiring and connections conform to local codes.
Q A standard 120-volt grounded electrical outlet is required under the sink for the faucet’s electrical power.
Q The wall outlet powering the tank must have electrical power supplied to it continuously.
Q This outlet must be fused and should not be controlled by the same wall switch that operates a food

waste disposer,unless you have a SinkTop Switch

™

from InSinkErator®.

Q If you suspect elevated levels of chlorine in your water,it is recommended to use our water

filtration system.

Q The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).

If it does, this will prevent your unit from operating properly.

Q Moving parts inside the tank causing a rattling noise is normal.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

Equipment Required:

Q Cordless Drill
Q Compression fitting,

T-fitting or saddle valve

Q Adjustable wrench

Q Phillips and flat blade screwdrivers
Q Pencil
Q Tape Measure
Q Level

Q Anchors for drywall
Q Hole saw

Q Basin wrench
Q Hole punch

If you intend to use the sprayer hole in your sink for your faucet, you may need a basin wrench and a
1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line.

See Step 1-B.

If you need to cut a mounting hole in your stainless steel sink, you may need a 11⁄4" - 11⁄2" hole saw made
for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other
than stainless steel.

WHAT YOU NEED TO GET STARTED

2

A standard 120-volt
grounded electrical
outlet is required
under the sink for the
unit’s electrical power.

A minimum of
2" of space is
required from
the center of the
faucet head
to the back wall
in order for this
appliance to
operate properly.

Note: Tank must be located
within 16" of faucet and
within 30" or less of a
standard grounded outlet.
DO NOT extend plumbing or
electrical lines.

2"

COMPONENTS IN THIS PACKAGE