Insinkerator SD-75 Parts List

PARTS LIST FOR COMMERCIAL DISPOSERS

MODEL SS-75 IN-SINK-ERATOR® 3/4 H.P.

(Includes Models SS-75-1, SS-75-2, SS-75-3)

ORDER BY PART NUMBER, NOT CODE NUMBER

(All PARTS F.O.B. FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)

(Minimum Paris Order $3.00)

EFFECTIVE March, 1972

PARTS LIST FOR COMMERCIAL DISPOSERS

MODEL SS-75 IN-SINK-ERATOR 3/4 H.P.

(Includes Models 'SS-75-1, SS-75-2, SS-75-3)

Code

Part No.

No.

1 11004 1 Mounting Flange
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Container
4 1491 6 Bolt, Mounting
5 11227 1 Pipe Plug
6 11006 1 Seal, Body-Shredder
7 12442 1 Body and Cover Assembly
8 112S2-A 1 Stationary Shredder

9 11260 1 Nut, Shredder
10 12445 1 Washer
11 12142 1 Washer, Fibre
12 12316 1 Rotor Shredder
13 12327 1 Upper End Bell - Includes

14 12321 1 Face Seal
15 12318 1 Spacer Sleeve
16 12319 1 Centrifugal Moisture Shield
17 12610 1 Bearing Assembly - Upper
18 12326 1 Oil and Water Retainer
19 11322 2 Woodruff Key
20 12611

21 11444 3 Washer
22 1491 3 Bolt
23 1470 1 Washer, Tail Pipe
24 5487 1 Tail Pipe
25 1461 1 Flange - Tail Pipe
26 1468 2 Bolt - Tail Pipe
27 12330-A

28 12331-A

29 1537 2 Spring - Centrifugal Switch
30 12348 1 Centrifugal Switch
31 7422 2 Screw
32 12393 1 Start Switch
33 5765 2 Screw
34 12370 1 Shell - Trim
35 12351-E 1 Stator Assembly

36 12351-A 1 Stator Assembly

No.

Reqd.

Codes 14-16-17-18

Bearing - Seal Kit Includes
Codes 9-10-11-14-15-16-17-18-19

Rotor & Shaft Assembly (Includes
Codes 29 & 30)i
208 Volt, 60 Cycle, Single Phase &
115/230 Volt, 60 Cycle, Single Phase
Rotor & Shaft Assembly
208 Volt, 60 Cycle, Three Phase &
230/460 Volt, 60 Cycle, Three Phase

208 Volt, 60 Cycle, Single Phase '

115/230 Volt, 60 Cycle, Single Phase

Description

ORDER BY PART NUMBER, NOT CODE NUMBER

(ALL PARTS F.O.B. FACTORY/DEPOT) (INCLUDE SERIAL AND MODEL NUMBER OF DISPOSER WHEN ORDERING)

(Minimum Parts Order $3.00)

Code

Part No.

No.

37 12549-A 1 Stator Assembly

38 12352-A 1 Stator Assembly

39 12433 1 Terminal Box Mounting Bracket •

40 12433-E 1 Terminal Box Mounting Bracket -

41 11448 4 Screw
42 12384 1 Bushing
43 11868 1 Capacitor - Single Phase Only
44 12387 1 Overload Protector

(Use above serial #42555 only)

44 12643 1 Overload Portector.

(Use below serial #42555 only) . :

45 12616 1 Overload Protector

45 12388 1 Overload Protector

46 12388 1 Overload Protector

230/460 Volt, 60 Cycle, Three Phase
47 12378 1 Clamp, Overload
48 5765 2 Screw
49 12372
50 12383
51 12381
52 12415
53 12399
54 12684
55 12395
56 12635
57 12490 3 Tube, Spacer
58 11940 3 Bolt, Thru
59 12396 1 Cover, Bottom
60 12586 2 Plug
61 11757-B 2 Leg (Optional)
62 12564 1 Ground Screw

No.

Reqd.

208 Volt, 60 Cycle, Three Phase

230/460 Volt, 60 Cycle, Three Phase

Single Phase

Three Phase

208 Volt, 60 Cycle. Single Phase
115/230 Volt, 60 Cycle, Single Phase

208 Volt, 60 Cycle, Single Phase :
115/230 Volt, 60 Cycle, Single Phase

(Use above serial #42699 only)
208 Volt, 60 Cycle, Three Phase

(Use below serial #42699 only)
208 Volt,60 Cycle, Three Phase

1

Terminal Box

1

Grommet

1

Screw

1

Bearing - Lower

1

Spring, Pre-load

1

End Frame, Lower

1

Fan

1

Retaining Ring

Description

EMERSON
IN-SINK-ERATOR DIVISION

EMERSON ELECTRIC CO.

Form No. C-123-72C PRINTED IN U.S.A.

4700-21ST STREET
RACINE, WISCONSIN 53406

PHONE: [phone]

CANADIAN

MODEL

MODEL

SS-75-10 115/230/60/1

SS-75-16

ISE

SS-75-11 208/60/1

SS-75-17 SS-75-12 230/460/60/3

SS-75-18

SS-75-13 208/60/3

SS-75-19

September,

1979

3

/4

H.P.

IN-SINK-ERATOR

Start with Serial #70,000

(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

ORDER BY PART NUMBER, NOT CODE NUMBER

MODEL

IN SINK ERATOR®

SS-75-10 115/230/60/1 SS-75-16
SS-75-11 208/60/1 SS-75-17
SS-75-12 230/460/60/3 SS-75-18
SS-75-13 208/60/3 SS-75-19

Code

Part No.

No.

1l 11004 1 Mounting Flange
2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Container
4 1491 6 Bolt, Mounting
5 11227 1 Pipe Plug
6 11006 1 Seal, Body-Shredder
7 12442 1 Body and Cover Assembly
8 11252-A 1 Stationary Shredder

9 11260 1 Nut, Shredder ,
10 12445 1 Washer
11 12142 1 Washer, Fibre
12 12944 1 Rotor Shredder
13 13081 1 End Bell Upper, Includes Codes

14 12936 1 Shield
15 12937 6 Screw
16 12934-A Seal Assembly
17 12935
18 12860
19 12319
20 12610
21 12326
22 11322 3 Woodruff Key
23 13080 1 Bearing - Seal Kit Includes Codes 9, 10

24 11444 3 Washer
25 1491 3 Bolt
26 1470 1 Washer, Tail Pipe
27 5487 1 Tail Pipe
28 1461 1 Flange - Tail Pipe
29 1468 2 Bolt - Tail Pipe
30 12947-A 1 Rotor & Shaft Assembly

208 Volt, 60 Hz. Single Phase &

31 12954 1 Centrifugal Switch Assembly
32 12948-A 1 Rotor & Shaft Assembly

33 7422 2 Screw
34 12393 1 Start Switch
35 12370 1 Shell-Trim
36 13075-C 1 Stator Assembly '

115/230 Volt, 60 Hz, Single Phase

No.

Req.

14 thru 21

Sleeve, Spacer
O'Ring
Centrifugal Moisture Shield
Bearing Assembly - Upper
Oil and Water Retainer

11, 14, 15, 16, 17, 18, 19, 20, 21, 22

Includes Code #31

115/230 Volt, 60 Hz, Single Phase

208 Volt, 60 Hz, Three Phase
230/460 Volt, 60 Hz, Three Phase

Description

CANADIAN
MODEL

Code

Part No.

No.

37 13075-B 1 Stator Assembly

38 13077-A 1 Stator Assembly

39 13076-A 1 Stator Assembly

40 12433 1 Terminal Box Mounting Brocket

41 12433-A 1 Terminal Box Mounting Bracket

42 11448 4 Screw
43 12384 1 Bushing

44 11868 1 Capacitor (Single Phase Only)
45 12387 1 Overload Protector

46 12388 1 Overload Protector

230/460 Volt, 60 Hz, Three Phase

47 12616 1 Overload Protector

48 12378 1 Clamp, Overload
49 5765 2 Screw
50 12372 1 Terminal Box
51 12383 1 Grommet
52 12381 1 Screw
53 12415 1 Bearing, Lower
54 12399 1 Spring, Pre-load
55 12684 1 End Frame, Lower
56 12395 1 Fan
57 12635 1 Retaining Ring
58 12490 3 Tube, Spacer
59 11940 3 Bolt, Thru
60 12396 1 Cover, Bottom
61 12564 1 Ground Screw
62 1175 7-8 2 Leg (Optional)

63 12643 1 Overload Protector

64 12387 1 Overload Protector

208 Volt, 60 Hz, Single Phase

65 12616 1 Overload Protector

No.

Req.

208 Volt, 60 Hz, Single Phase

230/460 Volt, 60 Hz, Three Phase

208 Volt, 60 Hz, Three Phase

Single Phase

Three Phase

115/230 Volt, 60 Hz, Single Phase
208 Volt, 60 Hz, Single Phase

208 Volt, 60 Hz, Three Phase

CANADIAN ONLY

115/230 Volt, 60 Hz, Single Phase

230/460 Volt, 60 Hz, Three Phase
208 Volt, 60 Hz, Three Phase

Description

4700-21ST STREET

11005

SPLASH BAFFLE

ISE

11249

SLEEVE GUARD

ORDER BY PART NUMBER, NOT CODE NUMBER

(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

IN-UNK-ERATOR DIVISION
EMERSON ELECTRIC CO.

RACINE. WISCONSIN 53406
PHONE: [phone]

4173
JAM RELEASE BAR

PRINTED IN U 5 A

ISE

MODEL NO. SS75

-

15

IN-SINK-ERATOR

1 11004 1 Flange, Mounting

NO.

29 1468 2 Screw, Tailpipe

COMMERCIAL DISPOSER

9230/460V/50Hz/3 Phase

Start Date:

03/04/82

Engineer Number:

13024K

3/4 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

PART NO. NO. REQ. DESCRIPTION

NO.

2 11016 1 Gasket, Mounting
3 11020A 1 Body, Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe. Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.

24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe

28 1461 1 Flange, Tailpipe

(lnd.Codes14.22)

Codes 9-11 & 14-22)

CODE

30 12948B 1 Rotor & Shaft Assy
31 12370 1 Trim, Band

32 1836A 2 Screw
33 13077B 1 Stator Assy
34 12433E 1 Bracket Assy

35 11448 4 Screw
36 12357 1 Insulation Tube
37 13128P 1 Overload, Protector
38 12378 1 Clamp, Overload
39 5765 2 Screw, Tapping
40 13396 1 Box, Terminal Assy

41 12381 1 Screw
42 12383 1 Grommet, Overload
43 12384 1 Bushing
44 2466A 1 Screw, Ground
45 12415 1 Bearing, Lower
46 12399 1 Washer, Spring
47 12684 1 End Frame, Lower
48 12395 1 Fan
49 12635 1 Ring, Retaining
50 12490 3 Tube,Spacer
51 12396 1 Cover, Bottom
52 11940A 3 Bolt, Thru
53 11757B 2 Tube Assy, Foot

PART NO. NO. REQ. DESCRIPTION

(Inc). Codes 45)

(Mounting)

(Incl. code 42)

(Optional)

COMMERCIAL DISPOSER

ISE

MODEL NO. SS75

-

21

NO.

1 11004 1 Flange, Mounting

29 1468 2 Screw, Tailpipe

Start Date:

Engineer Number:

IN-SINK-ERATOR (308 Volt/50Hz/3 Phase) 13024T

03/01/82

3/4 H. P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy. Rotor
13 13081 1

14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1

24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe

28 1461 1 Flange, Tailpipe

PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting
3 11020A 1 Body, Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe, Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252A 1 Shredder, Stationary
9 11260 1 Nut

End Bell Assy, Upper
(Incl. Codes 14-22)

Bearing Seal Kit (Incl. codes9-11
& 14-22)

CODE

NO.

30 12948B 1 Rotor & Shaft Assy

31 12370 1 Trim, Band
32 1836A 2 Screw
33 13077C 1 Stator Assy
34 12433E 1
35 11448 4 Screw
36 12357 1 Insulation Tube
37 13422N 1 Overload, Protector
38 12378 1 Clamp, Overload
39 8221 2 Screw, Tapping
40 13396 1

41 12381 1 Screw
42 12383 1 Grommet, Overload
43 12384 1 Bushing
44 2466A 1 Screw, Ground
45 12415 1 Bearing, Lower
46 12399 1 Washer, Spring
47 12684 1 End Frame, Lower
48 12395 1 Fan
49 12635 1 Ring, Retaining
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52 11940A 3 Bolt, Thru
53 11757B 2 Tube Assy, Foot

PART NO. NO. REQ. DESCRIPTION

(Ind. Codes 45)

Bracket Assy (Mounting)

Box, Terminal Assy
(Ind. code 42)

(Optional)

IN-SINK

-

ERATOR

May, 1985

3/4

H.P.

COMMERCIAL DISPOSER

ISE

ORDER BY PART NUMBER, NOT CODE NUMBER

(All P»rts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)

MODEL

SS-75-23
SS-75-24

115/208/230/60/1
208/230/460/60/3

MODEL NO. SS75

-24

IN-SINK-ERATOR

1 11004

1

Flange, Mounting

30 12948

-A 1

Rotor & Shaft Assy

Stator Assy (Three Phase)

COMMERCIAL DISPOSER

U.S.A.

(208-230/460/60/3Ø)

Start Date:

7/87

Engineer Number:

13384A

3/4 H.P.

CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket Mounting
3 11020-A 1 Body Any, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Any
8 11252.A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 1)322 3 Key, Woodruff
23 13080 1

24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipo
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw, Tailpipe

(Incl Codes 14 thru 22)

Bearing Seal Kit
(Incl Codes 9-11 & 14 thru 22)

CODE

NO.

31 12370 1 Trim, Band
32 1836-A 2 Screw
33 13077-A 1
34 12433-E 1 Bracket, Terminal Box

35 11448 4 Screw
36 12384 1 Bushing
37 13422-K 1 Overload, Protector

38 12378 1 Clamp. Overload
39 5765 2 Screw, Tapping
40 12372 1 Box, Terminal
41 12381 1 Screw
42 12383 1 Grommet, Overload
43 12415 1 Bearing, Lower
44 12399 1 Washer, Spring
45 12684 1 End Frame, Lower
46 12395 1 Fan
47 12635 1 Ring, Retaining
48 12490 1 Tube, Spacer
49 11940-A 1 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot

53 12357 1 Insulation Tube

PART NO. NO. REQ.

(Three Phase Only)

DESCRIPTION

(Three Phase)

(Three Phase)

(Optional)

MODEL NO.SS75

-25

IN-SINK-ERATOR

1 11004 1 Flange, Mounting

31 12954 1 Centrifugal Actuator

COMMERCIAL DISPOSER Start Date:

7/87

CANADIAN Engineer Number:

(115/208-230/60/1Ø) 13384B

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting

3 11020-A 1 Body Assy, Upper

4 1491 6 Screw, Mounting

5 11227 1 Pipe Plug

6 11006 1 Gasket, Shredder

7 12442 1 Body & Cover Assy

8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper

(IncI Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit

(IncI Codes 9-11

& 14 thru 22)
24 11444 3 Washer, lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 5487 1 Toilpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw, Tailpipe
30 12947-A 1 Rotor & Shaft Assy

(Single Phase)

(IncI Codes 31 & 47)

CODE

NO.

32 8221 2 Screw
33 12393 1 Switch, Start

34 12370 1 Trim, Band
35 1836-A 2 Screw
36 13075-C 1 Stator Assy

37 12433 1 Bracket Assy

38 11448 4 Screw
39 12384 1 Bushing
40 11868 1 Capacitor

41 13422-J1 1 Overload, Protector

42 12378 1 Clamp, Overload
43 5765 2 Screw, Tapping
44 12372 1 Box, Terminal
45 12381 1 Screw
46 12383 1 Grommet, Overload
47 12415 1 Bearing, Lower
48 12399 1 Washer, Spring
49 12684 1 End Frame, Lower
50 12395 1 Fan
51 12635 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-A 1 Screw, Ground
56 11757-B 2 Tube Assy, Foot

(Optional)

PART NO. NO. REQ. DESCRIPTION

(Single Phase Only)

(Single Phase Only)

(Single Phase)

(Mounting) (Single Phase)

(Single Phase Only)

(Single Phase)

IN-SINK-ERATOR

1 11004 1 Range, Mounting

1 13708 1 Centrifugal Actuator

COMMERCIAL DISPOSER

Start Date:

09/09/92

MODEL NO. SS75-27

Engineer Number:

(115/208/230 Volt/60Hz/1 Phase) 13659

3/4 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO.

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Plug, Pipe
6 11006 1 Gasket, Shredder
7 12442 1 Assy, Body & Cover
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Assy, Rotor Shredder
13 13722 1 Assy, Upper End Bell

14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Assy, Upper Bearing
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)

26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-A 1 Rotor & Shaft Assy.

NO.

REQ.

(Incl. Codes 14-22)

Kit, Bearing Seal (Incl. codes 9-11
& 14-22)

(Incl. Codes 31 & 47)

DESCRIPTION

CODE NO. PART NO.

32 8221 2 Screw (8-32x1/2)
33 13707 1 Switch, Start
34 12370 1 Trim Band
35 1836-A 2 Screw (8-32x1/2)
36 13713-A 1 Stator Assy
37 12433 1 Bracket Assy

38 11448 4 Screw (8-18x1/4)
39 12384 1 Bushing
40 11866 1 Capacitor
41 13422J 1 Overload Protector
42 12378 1 Clamp, Overload
43 8221 2 Screw (8-32x1/2)
44 13396 1 Box, Terminal Assy

45 12381 1 Screw (8-32x1-1/4)
46 12383 1 Grommet, Overload
47 13709 1 Bearing, Lower
48 13678 1 Spring, Pre-load
49 13710 1 End Frame, Lower
50 13676 1 Fan
51 13677 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-A 1 Screw, Ground
56 11757-B 2 Tube,Foot Assy.

(Optional)

NO.

REQ.

(Mounting)

(Incl. code 46)

DESCRIPTION

IN-SINK-ERATOR

1 11004 1 Flange, Mounting

28 1461 1 Flange, Tailpipe

(Optional)

.

COMMERCIAL DISPOSER

MODEL NO. SS75-28

(208/230-460 Volt/60Hz/3 Phase)

Start Date:

9-1-92

Engineer Number:

13659-A

3/4 H.P

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 .1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper

(Incl. Codes 14 thru 22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Wood luff
23 13080 1 Bearing Seal Kit (Incl.

codes 9-10-11 & 14 thru 22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe

CODE NO. PART NO.

29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy

31 12370 1 Trim.Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-A 1 Stator Assy
34 12433-E 1 Bracket Assy

35 11448 4 Screw (8-18x1/4)
36 12384 1 Bushing
37 13422-K 1 Overload, Protector
38 12378 1 Clamp, Overload
39 8221 2 Screw (8-32x1/2)
40 13396 1 Box, Terminal

41 12381 1 Screw (8-32x1-1/4)
42 12383 1 Grommet, Overload
43 13709 1 Bearing, Lower
44 13678 1 Spring, Pre-load
45 13747 1 End Frame, Lower
46 13676 1 Fan
47 13677 1 Ring, Retaining
48 12490 3 Tuba, Spacer
49 11940-A 3 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot

NO.

REQ.

DESCRIPTION

(Incl. Code 43)

(Mounting)

(Ind. code 42)

IN-SINK-ERATOR

1 11004 1 Flange, Mounting

31 13708 1 Centrifugal Actuator

COMMERCIAL DISPOER Start Date:

9-1-92

MODEL NO. SS75-28

Engineer Number:

(208/230/460 Volt/60Hz/3 Phase) 13659-A

3/4 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Plug, Pipe
6 11006 1 Gasket, Shredder
7 12442 1 Assy, Body & Cover
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Assy, Rotor Shredder
13 13722 1 Assy, Upper End Bell

(lncl.Codes14-22)
14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Assy, Upper Bearing
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Kit, Bearing Seal (Ind.

codes 9-11 & 14-22)
24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-A 1 Rotor & Shaft Assy.

(Incl. Codes 31 & 47)

CODE NO. PART NO. NO. REQ. DESCRIPTION

32 8221 2 Screw (8-32X1/2)
33 13707 1 Switch, Start
34 12370 1 Trim Band
35 1836-A 2 Screw (8-32x1/2)
36 13713-A 1 Stator Assy
37 12433 1 Bracket Assy

(Mounting)
38 11448 4 Screw (8-18X1/4)
39 12384 1 Bushing
40 11868 1 Capacitor
41 13422J 1 Overload Protector
42 12378 1 Clamp, Overload
43 8221 2 Screw (8-32x1/2)
44 13396 1 Box, Terminal Assy

(Incl. code 46)
45 12381 1 Screw (8-32x1-1/4)
46 12383 1 Grommet, Overload
47 13709 1 Bearing, Lower
48 13678 1 Spring, Pre-load
49 13710 1 End Frame, Lower
50 13676 1 Fan
51 13677 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-A 1 Screw, Ground
56 11757-B 2 Tube, Foot Assy.

(Optional)

IN-SINK-ERATOR

1 11004 1 Flange

, Mounting

28 1461 1 Flange, Tailpipe

COMMERCIAL DISPOSER Start Date:

MODEL NO. SS75-30 (C.S.A.)

(208/230/460 Volt/60Hz/3 Phase) 13569-C

02/26/93

Engineer Number:

3/4 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO.

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Beahng Assy, Upper
21 12326 1 Seal, Water& Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl,

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe

NO.

REQ.

(Incl. Codes 14 thru 22)

codes 9-10-11 & 14 thru 22)

DESCRIPTION

CODE NO. PART NO.

29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy

(Incl. Code 43)
31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714 -A 1 Stator Assy
34 12433-E 1 Bracket Assy

35 11448 4 Screw (8-18x1/4)
36 12384 1 Bushing
37 13422-K 1 Overload, Protector
38 12378 1 Clamp, Overload
39 8221 2 Screw (8-32x1/2)
40 13396 1 Box, Terminal

41 12381 1 Screw (8-32x1-1/4)
42 12383 1 Grommet, Overload
43 13709 1 Bearing, Lower
44 13678 1 Spring, Pre-load
45 13747 1 End Frame, Lower
46 13676 1 Fan
47 13677 1 Ring, Retaining
48 12490 3 Tube, Spacer
49 11940-A 3 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot

(Optional)

NO.

REQ.

(Mounting)

(Incl. code 42)

DESCRIPTION

IN-SINK-ERATOR

NO.

1 11004 1 Flange, Mount

ing

2 11016 1 Gasket, Mounting

3

11020-A 1 Body, Assy, Upper

4

1491 6 Screw

(1/4-20x3/4)

5

11227 1 Plug, Pipe

6

11006 1 Gasket, Shredder

7

12442 1 Assy, Body

&

Cover 8 11252-A 1 Shredder, Stationary

9

11260 1 Nut 10 12445 1 Washer

11

12142 1 Wash

er. Fiber

13 13722 1 Assy, Upper End Bell

(lncl.Codes14.22)

14

12936 1 Shield

16 12934-A 1 Assy, Seal

17

12935 1 Sleeve, Spacer

18

12860 1 O-Ring 19 12319 1 Slinger 20 12610 1 Assy,

Upper Bearing

21

12326 1 Seal. Water

&

Oil 22 11322 3 Key, Woodruff

23

13080 1 Kit, Bearing Seal (Incl.

Codes9

-

11 &14

-

22) 24 11444 3 Washer. Lock

26 1470 1 Gasket, Tailpipe

27

5487 1 Tailpipe

28

1461 1 Range, Tail

pipe 29 1468 2 Screw

(1/4-20x1/2)

30

13674-D 1 Rotor & Shaft Assy.

31 1413l 1 Centrifugal Actuator

COMMERICAL DISPOSER Start Date:

MODEL NO. SS75-31(EXPORT)

(115/230Volt/50Hz/1Phase) 13659-D

04/21/93

Engineer Number:

3/4 H.P.

ORDER BY PART NUMBER. NOT CODE NUMBER

CODE

12 12944 1 Assy, Rotor Shredder

15 1269 6 Screw (8-18x1/2)

25 3135 3 Screw (1/4-20x1)

PART NO. NO. REQ. DESCRIPTION

CODE

NO.

32 8221 2 Screw (8-32x1/2)
33 13707 1 Switch. Start
34 12370 1 Trim Band
35 1636-A 2 Screw (8-32x1/2)
36 13713-Q 1 Stator Assy
37 12433 1 Bracket Assy

38 11448 4 Screw (8-18x1/4)
39 11868 1 Capacitor
40 12378 1 Clamp, Overload
41 8221 2 Screw (8-32x1/2)
42 13396 1 Box, Terminal Assy

43 12381 1 Screw (8-32x1-1/4)
44 12383 1 Grommet, Overload
45 13422-L
46 12384 1 Bushing
47 2466-A 1 Screw, Ground
48 13709 1 Bearing, Lower
49 13678 1 Spring, Pre-load
50 13710 1 End Frame, Lower
51 13676 1 Fan
52 13677 1 Ring, Retaining
53 12490 3 Tube, Spacer
54 11940-A 3 Bolt. Thru
55 12396 1 Cover, Bottom
56 11757-B 2 Tube, Foot Assy.

(Optional)

PART NO. NO. REQ. DESCRIPTION

(Mounting)

(Incl. code 46)

1 Overload Protector

(Incl. Codes 31 & 48)

IN-SINK-ERATOR

l 11004 1 Flange, Moun

ting

28 1461 1 Range, Tailpipe

COMMERCIAL DISPOSER Start Date:

MODEL NO. SS75-32 (EXPORT)

(208/460Volt/50Hz/3Phase) 13659-E

04/21/93

Engineer Number:

3/4 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

NO.

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Mug
6 11006 1 Gasket. Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe

PART NO.

NO.

REQ.

(Incl. Codes 14 thru 22)

codas 9-10-11 & 14 thru 22)

DESCRIPTION

CODE

NO.

29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy

31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-A 1 Staler Assy
34 12433-E 1 Bracket Assy

35 11448 4 Screw (8-18x1/4)
36 13422-AG 1 Overload, Protector
37 12378 1 Clamp, Overload
38 8221 2 Screw (8-32x1/2)
39 13396 1 Box, Terminal

40 12381 1 Screw (8-32x1-1/4)
41 12383 1 Grommet, Overload
42 12384 1 Bushing
43 2466-A 1 Screw, Ground
44 13709 1 Bearing, Lower
45 13678 1 Spring, Pre-load
46 13747 1 End Frame, Lower
47 13676 1 Fan
48 13677 1 Ring, Retaining
49 11940-A 3 Bolt, Thru
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52 11757-B 2 Tube Assy, Foot

(Optional)

PART NO.

NO.

REQ.

DESCRIPTION

(Incl. Code 44)

(Mounting)

(Incl. code 42)

IN-SINK-ERATOR

1 11004 1 Range, Mounting

20 1461 1 Range, Tailpipe

.

COMMERCIAL DISPOSER Start Date:

MODEL NO. SS75-33 (EXPORT)

(380 Volt/50Hz/3Phase) 13659-G

04/21/93

Engineer Number:

3/4 H.P

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE

NO.

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 1 Gasket. Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5457 1 Tailpipe

PART NO. NO. REQ. DESCRIPTION

(Incl. Codes 14 thru 22)

codes 9-10-11 & 14 thru 22)

CODE

NO.

29 1468 2 Screw (1/4-20x1/2)
30 13674-G 1 Rotor & Shaft Assy

31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-B 1 Stator Assy
34 12433-E 1 Bracket Assy

35 11448 4 Screw (8-18x1/4)
36 13422-N 1 Overload, Protector
37 12378 1 Clamp, Overload
38 8221 2 Screw (8-32x1/2)
39 13396 1 Box, Terminal

40 12381 1 Screw (8-32x1-1/4)
41 12383 1 Grommet, Overload
42 12384 1 Bushing
43 2466-A 1 Screw, Ground
44 13709 1 Bearing, Lower
45 13678 1 Spring, Pre-load
46 13747 1 End Frame, Lower
47 13676 1 Fan
48 13677 1 Ring, Retaining
49 11940-A 3 Bolt, Thru
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom
52 11757-B 2 Tube Assy. Foot

PART NO. NO. REQ. DESCRIPTION

(Incl. code 42)

(Optional)

(Incl. Code 44)

(Mounting)

IN-SINK-ERATOR

1 12506-D 1 No. 5 Mounting Assy

30 13551-A 1 Rotor & Shaft Assy

52 11940-A 3 Bolt, Thru

COMMERCIAL DISPOSER Start Date:

MODEL NO. SD 75

Engineer Number:

230 Volt/50Hz/1Phase 13531

11/01/89

CODE NO. PART NO.

ORDER BY PART NUMBER, NOT CODE NUMBER

NO.

REQ.

2 11016 1 Gasket, Mounting
3 11020-A 1 Body Assy. Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shreddder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 13549 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw, Tqpping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Wooddruff
23 13080 1 Bearing Seal Kit

24 11444 3 Washer, Lock
25 3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 3851 1 Tailpipe
28 1461 1 Flange, Tailpipe
29 1468 2 Screw, Tailpipe

(Inc Codes 14-22)

(Inc Codes 9-11 & 14-22)

DESCRIPTION

CODE NO. PART NO.

31 12954-A 1 Centrifugal Actuator
32 13556 2 Screw
33 12393 1 Switch, Start
34 1836-A 2 Screw
35 12370 1 Trim, Band
36 13075-P 1 Stator Assy
37
38 11448 4 Screw
39 11868 1 Capacitor
40 12384 1 Bushing
41 2466A 1 Screw, Ground
42 12372 1 Box. Terminal
43 12381 1 Screw
44 13559 1 Grommet
45 12415 1 Bearing, Lower
46 12399 1 Washer, Spring
47 13547 1 End Frame, Lower
48 12395 1 Fan
49 12635 1 Ring, Retaining
50 12490 3 Tube, Spacer
51 12396 1 Cover, Bottom

NO.

REQ.

(Incl Codes 31 & 45)

1 Bracket Assy. Mounting

DESCRIPTION

IN-SINK-ERATOR

1 11004 1 Flange, Mounting

25

30 12948-A 1 Rotor & Shaft Assy

49 11940-A 3 Bolt, Thru

COMMERCIAL DISPOSER Start Date:

MODEL NO. SD 75-1

Engineer Number:

415 Volt/50Hz/3 Phase 13532 A

11/01/89

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting
3 11020-A 1 Body Assy, Upper
4 1491 6 Screw, Mounting
5 11227 1 Pipe Plug
6 11006 1 Gasket, Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer, Fiber
12 13549 1 Shredder Assy, Rotor
13 13081 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw, Tapping
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Slinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal, Water & Oil
22 11322 3 Key, Wooddruff
23 13080 1 Bearing Seal Kit

24 11444 3 Washer, Lock

3135 3 Screw
26 1470 1 Gasket, Tailpipe
27 3851 1 Tailpipe
28 1461 1 Flange. Tailpipe
29 1468 2 Screw, Tailpipe

(Inc Codes 14-22)

(Inc Codes 9-11 & 14-22)

CODE NO. PART NO.

31 1836-A 2 Screw
32 12370 1 Trim, Band
33 13077-A 1 Stator Assy
34 12357 1 Insulation, Tubing
35
36 11448 4 Screw
37 12384 1 Bushing
38 2466A 1 Screw, Ground
39 12372 1 Box, Terminal
40 12381 1 Screw
41 13559 1 Grommet
42 12415 1 Bearing, Lower
43 12399 1 Washer, Spring
44 12684 1 End Frame, Lower
45 12395 1 Fan
46 12635 1 Ring, Retaining
47 12490 3 Tube, Spacer
48 12396 1 Cover, Bottom

NO.

REQ.

(Incl Codes 42)

1 Bracket Assy, Mounting

DESCRIPTION

SISSONS

1 11004 1 Flange, Mounting

31 13708 1 Centrifugal Actuator

(Optional)

COMMERCIAL DISPOSER Start Date:

MODEL NO. SD75-3 (Export)

03/12/93

Engineer Number:

(115/208/230 Volt/50Hz/1Phase) 13711

3/4 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO.

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Plug, Pipe
6 11006 1 Gasket, Shredder
7 12442 1 Assy, Body & Cover
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer. Fiber
12 12944 1 Assy, Rotor Shredder
13 13722 1 Assy, Upper End Bell

14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Assy, Seal
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Stinger
20 12610 1 Assy, Upper Bearing
21 12326 1 Seal. Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Kit. Bearing Seal (Ind.

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 5487 1 Tailpipe
28 1461 1 Range, Tailpipe
29 1468 2 Screw (1/4-20x1/2)
30 13674-D 1 Rotor & Shaft Assy.

(Ind. Codes 31 & 47)

NO.

REQ.

(Incl. Codes 14-22)

codes 9-11 & 14-22)

DESCRIPTION

CODE NO. PART NO.

32 8221 2 Screw (8-32x1/2)
33 13707 1 Switch, Start
34 12370 1 Trim Band
35 1836-A 2 Screw (8-32x1/2)
36 13713-G 1 Stator Assy
37 12433 1 Bracket Assy

38 11448 4 Screw (8-18x1/4)
39 12384 1 Bushing
40 11868 1 Capacitor
41 13422-L 1 Overload Protector
42 12378 1 Clamp, Overload
43 8221 2 Screw (8-32x1/2)
44 13396-D 1 Box, Terminal Assy

45 12381 1 Screw (8-32x1-1/4)
46 13559 1 Plug, Button
47 13709 1 Bearing, Lower
48 13678 1 Spring, Pre-load
49 13710 1 End Frame, Lower
50 13676 1 Fan
51 13677 1 Ring, Retaining
52 12490 3 Tube, Spacer
53 11940-A 3 Bolt, Thru
54 12396 1 Cover, Bottom
55 2466-B 1 Screw, Ground
56 11757-B 2 Tube, Foot Assy.

NO.

REQ.

(Mounting)

(Ind. code 46)

DESCRIPTION

SISSONS

1 11004 1 Flange, Mounting

28 1461 1 Flange, Tailpipe

COMMERCIAL DISPOSER Start Date:

MODEL NO. SD75-4 (Export)

Engineer Number:

(208/230/460Volt/50Hz/3Phase) 13711-A

02/26/93

3/4 H.P.

ORDER BY PART NUMBER, NOT CODE NUMBER

CODE NO. PART NO. NO. REQ. DESCRIPTION

2 11016 1 Gasket, Mounting
3 11020-A 1 Body, Assy, Upper
4 1491 6 Screw (1/4-20x3/4)
5 11227 1 Pipe, Plug
6 11006 1 Gasket. Shredder
7 12442 1 Body & Cover Assy
8 11252-A 1 Shredder, Stationary

9 11260 1 Nut
10 12445 1 Washer
11 12142 1 Washer. Fiber
12 12944 1 Shredder Assy, Rotor
13 13722 1 End Bell Assy, Upper

14 12936 1 Shield
15 1269 6 Screw (8-18x1/2)
16 12934-A 1 Seal Assy
17 12935 1 Sleeve, Spacer
18 12860 1 O-Ring
19 12319 1 Stinger
20 12610 1 Bearing Assy, Upper
21 12326 1 Seal. Water & Oil
22 11322 3 Key, Woodruff
23 13080 1 Bearing Seal Kit (Incl.

24 11444 3 Washer, Lock
25 3135 3 Screw (1/4-20x1)
26 1470 1 Gasket, Tailpipe
27 70076 1 Tailpipe

(Incl. Codes 14 thru 22)

codes 9-10-11&14 thru 22)

CODE NO. PART NO. NO. REQ. DESCRIPTION

29 1468 2 Screw (1/4-20x1/2)
30 13674-K 1 Rotor & Shaft Assy

31 12370 1 Trim, Band
32 1836-A 2 Screw (8-32x1/2)
33 13714-G 1 StatorAssy
34 12433-A 1 Bracket Assy

35 11448 4 Screw (8-18x1/4)
36 12384 1 Bushing
37 N/A 1 Overioad, Protector
36 12378 1 Clamp, Overload
39 8221 2 Screw (8-32x1/2)
40 13396-D 1 Box, Terminal

41 12381 1 Screw (8-32x1-1/4)
42 13559 1 Plug, Button
43 13709 1 Bearing, Lower
44 13678 1 Spring, Pre-load
45 13747 1 End Frame, Lower
46 13676 1 Fan
47 13677 1 Ring, Retaining
48 12490 3 Tube, Spacer
49 11940-A 3 Bolt, Thru
50 12396 1 Cover, Bottom
51 2466-A 1 Screw, Ground
52 11757-B 2 Tube Assy, Foot

(Optional)

(Incl. Code 43)

(Mounting)

(Incl. code 42)