In-Sink-Erator HCLCSS Installation Manual

Instant Hot Water Dispenser
Owner’s Manual
INVOLVE VIEW
INVOLVE WAVE
™ ™
Dispensador de agua caliente instantánea
Manual del usuario
Distributeur d’eau très chaude instantanée
Manuel du propriétaire
Installation, Care & Use
Instalación, cuidado y uso Installation, soin et utilisation
INVOLVE VIEW
INVITE CONTOUR
INVITE CLASSIC
™ ™
1.800.558.5700 www.insinkerator.com
44671 REV A
InSinkErator puede realizar mejoras y/o modificaciones en las especificaciones en cualquier momento, y bajo su exclusivo
InSinkErator se réserve le droit, à son entière discrétion, d’apporter en tout temps des améliorations ou des modifications
aux spécifications, et ce, sans préavis ou obligation de sa part, ou de modifier ou de supprimer des modèles.
without notice or obligation and further reserves the right to change or discontinue models.
El logotipo Emerson es una marca registrada y una marca de servicio de Emerson Electric Co.
criterio, sin previo aviso u obligación; además, se reserva el derecho de cambiar o suspender los modelos.
©2013 InSinkErator, una unidad comercial de Emerson Electric Co. Todos los derechos reservados.
The Emerson logo is a trademark and a service mark of Emerson Electric Co.
©2013 InSinkErator, a business unit of Emerson Electric Co. All Rights Reserved.
Le logo Emerson est une marque de commerce et de service d'Emerson Electric Co.
©2013 InSinkErator, une unité commerciale d'Emerson Electric Co. Tous droits réservés.
INVITE CONTOUR
INVITE CLASSIC
To see a tutorial of this installation:
Para ver un tutorial de esta instalación ingrese a
Pour voir un tutoriel de cette installation
http://goo.gl/AZOHu
INVOLVE WAVE
We are delighted that you have chosen the InSinkErator® Instant Hot Water Dispenser to be
NOTICE
NOTICE
a part of your home. This unique appliance will save you time and effort in the kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why millions of people are now using an InSinkErator Instant Hot Water Dispenser.
We are confident that by following our step-by-step instructions, you’ll soon be enjoying the convenience of instant hot water.
Identify the model of your instant hot water dispenser and record it here:______________________
H-Contour-SS H-Classic-SSH-View-SS H-Wave-SSHC-View-SS HC-Wave-SS
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this
instant hot water dispenser. This particular unit is not intended for commercial use.
Make sure that all electrical wiring and connections conform to local codes. A standard 115-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power. The wall outlet powering your dispenser must have power supplied to it continuously. This outlet must be fused and should not be controlled by the same wall switch that operates the disposer,
unless you have a SinkTop Switch™ from InSinkErator®.
It is recommended that a dedicated control valve be installed on the cold water line supplying water to this
system.
If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation
of this unit, it is recommended to use our water filtration system. This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the
number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty water discharged from the hot water dispenser may indicate the need for service or replacement of this product.
The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).
If it does, this will prevent your unit from operating properly.
Moving parts inside the tank causing a rattling noise is normal.
WHAT YOU NEED TO GET STARTED
Equipment Required:
n Drill n T-fitting n Dedicated control valve n Adjustable wrench
n Phillips and flat blade screwdrivers n Pencil n Tape Measure / Ruler n Level
HOW TO USE THIS INSTRUCTION MANUAL
These instructions are separated into main sections, indicated by numbers, and subsections, indicated by capital letters. The manual is setup this way to allow you to take a break at any point after completing a section or subsection without affecting the installation process.
What you’ll see in the instruction manual:
Provides a step-by-step narrative describing the installation step, with check boxes that
1
can be marked as you progress through the installation.
2
Contains simple illustrations that provide visual instruction to support the narrative.
3
Important safety messages that will require your attention during the step.
NOTICE
INSTALLING THE FAUCET - VIEW/WAVE
a
2
Proper ty Damage: D o not pinch or brea k copper
tubing. D o not distort t he last 1 inch of tu bing.
Warning indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
Caution indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Notice is used to address practices not related to personal injury.
View/ Wave
Unpack dispenser components. On a firm, flat sur face, carefully
straighten the copper tubing using hands only.
3
1
Equipment You May Need:
Anchors for drywall Hole saw
If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a 1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line. See Step 1-B.
If you need to cut a mounting hole in your stainless steel sink, you may need a 1-1/4" – 1-1/2" hole saw made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other than stainless steel.
To see a tutorial of this installation: http://goo.gl/AZOHu
Basin wrench
Hole punch
2
OVERVIEW OF A
COMPLETED SETUP
3
COMPONENTS IN THIS PACKAGE
START HERE
PREPARATION
HC-View-SS
HC-Wave-SS
H-View-SS
H-Wave-SS
Extension & Star Nut*
Washers
1-1/ 4" 1-1/ 4"
Small Steel* FiberRubber* Large Steel
Extension & Star Nut*
Washers
1-1/ 4"
Small Steel* FiberRubber* Large Steel
1-1/ 4"
Trim Ring
3/4" Screws (2)
1-5/ 16"
3/4" Screws (2)
1-5/ 16"
3/8" Tube
Quick Connector
1-1/ 2"
1-1/ 2"
Brass Nut /Ferrule /
Tube Insert
Tank
Tank
1
a
Required minimum from center of hole
to wall
Maximum counter thickness (depth)
HC-View-SS ..... 2-5⁄8" .................... 3"
H-View-SS ....... 2-5⁄8" .................... 3"
HC-Wave-SS .... 2-5⁄8" .................... 3"
H-Wave-SS ...... 2-3⁄8" .................... 3"
H-Contour-SS ... 2" ........................... 3"
H-Classic-SS .... 2" ........................... 3"
Identify locations for the dispenser
faucet, tank and filter (if applicable).
Check to make sure there is proper
clearance (see chart at left) for dispenser handles to be fully opened.
Check to make sure counter is not
too thick (see chart at left).
Make sure there is a grounded
electrical outlet under the sink.
The wall outlet for your dispenser must have power supplied to it continuously
and must be fused. It should not be controlled by the same wall switch
that operates your disposer, unless using an InSinkErator SinkTop Switch™.
b
If you have to drill through sink or
countertop, you may need to rent or
purchase the appropriate tools.
Turn off water supply. If using the sink sprayer hose hole,
remove nut that connects sprayer hose at bottom of faucet.
Using adjustable wrench, remove
nut connecting sprayer washer flange in sprayer hole.
Plug hose opening with either a 1/8"
plug or a 1/4" cap (not supplied).
H-Contour-SS
H-Classic-SS
Semi-Circular
Mounting Plate
Semi-Circular
Mounting Plate
Wing Nut
Trim Ring
*component parts pre-installed on dispenser
4
Flat Gasket
Flat GasketWing Nut
3/4" Screws (2)
3/4" Screws (2)
Tank
Tank
C
Required Hole Size
1-1⁄4" – 1-1⁄2"
Dependent on model
Consult a professional before drilling into
a surface other than stainless steel.
To see a tutorial of this installation: http://goo.gl/AZOHu
What if you don’t have a sprayer hole or don’t want to use it?
Many homeowners replace the
soap dispenser in their sink with an instant hot water dispenser.
If drilling a hole into a stainless steel
sink or counter top, you can cut a mounting hole for the dispenser with a hole saw for stainless steel, or you can use a hole punch.
5
INSTALLING THE FAUCET - View/Wave
NOTICE
NOTICE
2
a
View/Wave
Unpack dispenser components. On a firm, flat surface, carefully
straighten the copper tubing using hands only.
INSTALLING THE FAUCET - Contour/Classic
2
a
Contour/Classic
Unpack dispenser components. On a firm, flat surface, carefully
straighten the copper tubing using hands only.
6
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
b
1-1/4" Small
Steel Washer
1-1/4" Small
Rubber Washer
Standard 1-1⁄2" hole Hole larger than 1-1⁄2"
Faucet is factory-ready for installation
into a standard 1-1⁄2" sink/counter hole.
1-1/4" Small
Steel
Washer
1-1/4"
Small
Rubber
Washer
1-5/16" Large Steel Washer
C
Hot & Cool models only
Fiber
Washer
An assistant may be needed to hold
Figure 1 Figure 2
If sink/counter thickness exceeds 3/4"
a hole diameter of 1-1⁄2" is required.
Star Nut
the dispenser head in place
while securing the dispenser.
1-1/4" Small
Steel
Washer
Fiber
Washer
1-1/4"
Small Rubber Washer
Star Nut
View/Wave For a standard 1-1⁄2" sink/counter hole
Feed tubes down through the hole in
the sink/counter until the base is at rest. Set faucet at desired angle.
Large washer required for sink holes
larger than 1-1⁄ 2" or for porcelain sinks with radius or beveled holes.
Before feeding tubes through sink
hole, remove extension. Place 1-5/16" large steel washer over threads on faucet base. Reinstall extension.
View/Wave
From under sink, slide 1-1/2" fiber washer
over threaded extension. Thread star nut onto extension until snug.
Hot & Cool models only
Attach the quick connector to the
ends of the copper tubes running from the dispenser.
Install a white 3/8" tube into other
end of quick connector.
Installing into hole smaller than 1-1⁄2"
Unscrew and remove threaded extension
from valve body. Do not discard, as you will need this later (See Figure 1).
Leave small washers in place.
Feed tubes down through the hole in
the sink/counter until the base is at rest. Set faucet at desired angle.
From under sink, slide 1-1/2" fiber washer
over faucet base. Reinstall threaded extension onto the base until snug. Thread star nut onto extension until snug (See Figure 2).
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
b
Trim
Flat
Gasket
Ring
Make sure to use rubber gasket
to ensure proper seal.
C
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
To see a tutorial of this installation: http://goo.gl/AZOHu
Contour/Classic
Install chrome trim ring
onto base of faucet.
Ensure that the flat gasket is
properly seated into the base of the dispenser head and will surround the sink mount.
Feed tubes down the hole in
the sink or countertop until the base is at rest on the sink or countertop surface.
Contour/Classic
From under the sink, place the
semi-circular mounting plate onto the threaded stud.
Place wing nut onto the threaded
stud. Make sure faucet head is at the desired angle. Tighten the wing nut until snug, while ensuring the semi-circular mounting plate extends beyond the sink hole.
Do not over tighten wing nut. May cause damage to faucet.
7
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
MOUNTING THE TANK
NOTICE
NOTICE
Brass Nut
Ferrule
NOTICE
NOTICE
NOTICE
NOTICE
Brass Nut
Ferrule
Brass Insert
Brass Nut
Ferrule
Plastic
tube
3
a
Property Damage: Tank must be located
within 16" of faucet and within 30" or less
of a standard grounded outlet. DO NOT extend
plumbing or electrical lines.
Tank must be
mounted level
to ensure
proper operation.
Select a spot under the sink to mount
tank vertically within reach of both plumbing and electrical connections. The tank should be within 16" or less of faucet water lines and within 30" or less of a standard grounded outlet.
While holding tank in place on
the spot selected for installation, use a pencil to mark locations for 2 hanging screws.
FINAL WATER CONNECTION
5
a
Brass
Nut
3/8"
Plastic
Tube
Property Damage: Join remaining tube
to cold water supply only.
Ferrule
Brass Insert
HC-View/HC-Wave
Install a T-fitting (not included) onto the
cold water supply line.
Install dedicated water control valve with
3/8" compression fitting.
At the end of the white 3/8" tube from
the quick-connector, slide the supplied brass nut and ferrule over the tube and then push in the brass tube insert.
Insert the white 3/8" tube into the 3/8"
compression fitting and tighten.
CONNECTING FAUCET TO TANK
4
8
b
Leave 1/4" for
hanging tank.
Mount tank vertically in an area that
allows clearance on the underside of
the tank for drainage, if necessary.
DO NOT over tighten screws.
a
(1) (2) (3)
Property Damage: Pinched or blocked water
lines may cause damage to the dispenser tank.
Check to make sure tubes are connected
properly and are pushed down as far as possible.
To see a tutorial of this installation: http://goo.gl/AZOHu
Screws provided are for use in wood studs or cabinets only. Use wall anchors (not supplied) for installation into drywall.
Pre-drill 1/8" pilot holes at marks. Turn screws into pre-drilled holes,
leaving 1/4" exposed.
Hang the tank on the screws. Tighten the screws with only 1/2
turn clockwise.
Without depressing the gray button,
place the snap-connect fitting at the end of the blue 1/4" tube onto the left fitting on the tank, pushing until it clicks into place. (1)
Slip the flexible white 7/16" tube
over barbed middle fitting and slide down approximately 1/2". (2)
Slip the clear 5/16" tube over the
far right smooth fitting and slide down approximately 1/2". (3)
Visually check for pinched or
crimped tubes.
Hose clamps are not needed for any
of the connections.
6
a
1/4"
Copper
Tube
Brass
Nut
Ferrule
H-View/H -Wave/Contour/Classic
Install a T-fitting (not included) onto the
cold water supply line.
Install dedicated water control valve with
1/4" compression fitting (not included).
At the end of the copper 1/4" tube,
slide the brass nut and ferrule provided with the control valve over the tube.
Property Damage: Join remaining tube
to cold water supply only.
Insert the copper tube into the 1/4"
compression fitting and tighten.
FILL TANK & THEN CONNECT POWER
a
Scalding Hazard: The faucet dispenses
near-boiling (212ºF) water which can
instantly cause scalds or burns. Use care
when operating this appliance.
b
Electric Shock Hazard: A standard grounded
outlet within 30" of the dispenser is required
under the sink. Do not use an extension
cord set with the dispenser.
Turn on the cold water supply. Depress the dispenser’s HOT
handle and hold it until water flows from the spout (approximately 1 to 2 minutes).
Run the water for at least 2 minutes to
flush lines (both the hot and cold handles independently if applicable).
Check all connections to ensure they are
tight and that there are no leaks.
Plug in instant hot water tank.
Water will be cold at first. Allow 12-15 minutes for water to reach
target temperature. Gurgling or hissing is normal during the
initial heating cycle.
9
Electric Shock Hazard: Using an ungrounded or improperly connected
NOTICE
NOTICE
NOTICE
NOTICE
appliance can result in serious injury or death from electrical shock.
This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is properly grounded.
Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system. DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an authorized InSinkErator Service agent for repairs or replacement components.
Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Leak Hazard: Regularly inspect dispenser and plumbing fittings for leaks, which can cause property damage and/or could result in personal injury.
Property Damage: To avoid water damage, replace any loose or split tubing. Periodically inspect the unit for any signs of leakage and immediately remove from service any unit suspected of leaking.
An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid possible property damage and personal injury, this instant hot water dispenser should be regularly examined for leakage and/or corrosion and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage. To check for corrosion, examine the appearance of the dispensed water in a clear glass once every three ( 3) months. If there is any discoloration or rusty appearance, unplug and drain unit as described in the Seasonal Storage/Drainage section on page 12 of this manual. If the water discoloration remains after draining and refilling unit, discontinue use and contact an authorized InSinkErator service agent.
10
IN-HOME FULL SERVICE LIMITED WARRANTYIMPORTANT SAFETY INSTRUCTIONS
This warranty is provided by InSinkErator®, a business unit of Emerson Electric Co., ( “InSinkErator” or “Manufacturer” or “we” or “our” or “us” ) to the original consumer owner of the InSinkErator product with which this warranty is provided (the “InSinkErator Product”), and any subsequent owner of the residence in which the Product was originally installed ( “Customer” or “you” or “your”).
InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject to the exclusions described below, for a period of 3 years (the “Warranty Period”) , commencing on the later of: (a) the date your InSinkErator Product is originally installed, ( b) the date of purchase, or ( c) the date of manufacture as identified by your InSinkErator Product serial number. You will be required to show written documentation supporting (a ) or (b). If you are unable to provide documentation supporting either (a ) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute discretion, based upon your InSinkErator Product serial number.
Permitted Uses You may use your InSinkErator Product hot /cold water tank and filter system in combination with any genuine InSinkErator Product instant hot water dispensers and component parts, and with any authentic Dornbracht hot or hot/cold water dispensers and component parts (collectively, “Dornbracht Water Dispenser”) which Dornbracht expressly states in writing is/are compatible with such InSinkErator Product(s) . Use of your InSinkErator Product with any other manufacturer’s products or in any combination other than as expressly stated above will void this warranty.
What is Covered This warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products used by a consumer Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY S HALL BE LIMITED TO REPAIR OR REPL ACEMENT OF THE INSINKERATOR PRODUCT, PROVIDED, THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY IS PRACTICABLE, WE MAY PROVIDE YOU WITH A REFUND OF YOUR PU RCHAS E PRICE OR A CREDIT TOWARDS ANOTHER INSINKERATOR PRODUCT.
What is not Covered
This limited warranty does not extend to and expressly excludes:  • Losse sorda magesorthei nabilitytoop erateyourInSinkEratorProductres ulting fromconditio nsbeyondthe Manufacturer’s control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s), failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or local electrical and plumbing codes.
 • Wearandtearexpectedtooccurduringthenormalcourseofuse,includingwithoutlimitation,cosmeticrust,scratches, dents or comparable and reasonably expected losses or damages.
 • LossesordamagescausedbytheDornbrachtWaterDispenser
In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or industrial application.
No Oth er Express Warranty Applies This warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty, written or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on behalf of Manufacturer. The terms of this warranty shall not be modified by the Manufacturer, the original owner, or their respective successors or assigns.
What we will do to Correct Problems If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions concerning your InSinkErator Product or how to determine when service is needed, please call the toll free InSinkErator AnswerLine at 1 ( 800 ) 558-5700, or visit our website at ww w.insinkerator.com. You may also notif y us at: InSinkErator Service Center, 4700 21st Street, Racine, Wisconsin 53406 USA.
The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your installation receipt, or (b) the date shown on your purchase receipt.
Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator Product is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service Center. Please contact your InSinkErator Service Cente r directly to receive in home warranty repair or replacement service. Only an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator service representative.
If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement ser vices will be provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired, the warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original Warranty Period.
Limitation of Liability TO THE EX TENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER SORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILIT Y TO YOU EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.
The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or equipment.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
InSinkErator® may make improvements and /or changes in the specifications at any time, in its sole discretion, without notice or obligation and further reserves the right to change or discontinue models.
11
Loading...
+ 14 hidden pages