InSinkErator FOODSERVICE DISPOSER Installation Manual
FOODSERVICE DISPOSER
Installation Manual
WARNING
CAUTION
www.insinkerator.com/foodservice
WARNING indicates a hazardous situation which, if not avoided, could result in
death or seious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE is used to address practices related to physical injury
Please be certain that the person who installs or uses this appliance carefully reads
and understands the Safety Instructions contained in this manual.
Part No. 13954 Rev.B
2
Table of Contents
Introduction
Introduction .................................................................................... 4
Clean the Drain Line ....................................................................... 4
Typical Installation .......................................................................... 4
Required Tools/Materials ................................................................ 4
Instructions Pertaining to
Risk of Fire, Electrical Shock, or Injury to Persons.......................... 5
Installing the Disposer
Disposer Mounting ......................................................................... 6
Mounting Adaptors ........................................................................ 6
Standard InSinkErator Mountings
#5 Mounting Assembly .................................................................. 7
#6, 7, and Sink Bowl Mounting Assemblies ................................... 8
Special InSinkErator Mountings ................................................................. 8
Plumbing Connections
Drain Line Connections .................................................................. 9
Water Supply Connections ............................................................ 9
Routing Water Flow ......................................................................... 9
Standard Motor Connection Wiring Diagrams ........................................ 10
Electrical Connections
Electrical Connections ................................................................. 11
Disposer Controls ......................................................................... 11
Operating Instructions
Operating the Disposer ................................................................ 12
Grinding Tips ................................................................................ 12
Troubleshooting .......................................................................................... 13
Warranty ...................................................................................................... 16
3
Read all warnings before proceeding.
Introduction
INTRODUCTION
The InSinkErator Foodservice food waste disposer is
UL® and cUL® Listed when installed in conjunction with
InSinkErator mounting adaptors and controls (see Figure
1 for typical installation).
See Table 1 (page 6) for the approved disposer/
mounting adaptor combinations.
Important – These installation instructions are for
the benet of the installing contractor. InSinkErator
and/or InSinkErator Factory Authorized Service
Centers do not make original installations. For technical
information not covered in these instructions,
contact the supplier, an InSinkErator Field Sales
Representative, or InSinkErator Foodservice Sales
and Service at 1-800-845-8345.
CLEAN THE DRAIN LINE
With a drain line auger, clear away all hardened waste
material in the horizontal drain pipe running from the
drain trap to the main waste line.
TYPICAL INSTALLATION
A typical Foodservice disposer installation incorporates
the following connections (see Figures 1 and/or 9):
• Water shut off valve
• Syphon breaker
• Solenoid valve
• Start/stop switch (Control Center)
• Sink or trough
• Flow control valve
REQUIRED TOOLS/MATERIALS
The following items are needed to install the disposer:
• Screwdriver
• Adjustable wrench
• Pipe wrench
• Wire nuts
• 7/16" nut driver
The following items may be needed to install
the disposer:
• Plumbing putty
• Hacksaw
• Drain auger
Figure 1. Typical Installation
4
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
NOTICE
PERSONAL INJURY/PROPERTY DAMAGE
If the electrical installer is not experienced in
electrical installation, we recommend seeking
competent professional assistance. Disposer or
accessory damage due to improper installation is
not covered under warranty. All installations must
comply with local electrical codes.
PERSONAL INJURY
• Food waste disposers are designed to grind
and dispose of normal food waste. Inserting
materials or items other than food waste into
the disposer could cause personal injury and/or
disposer damage.
• To reduce the risk of injury from materials that may
be expelled from the disposer grind chamber,
ensure that the disposer bafe is properly installed.
• To prevent the ejection of food waste and to keep
foreign materials out of the grind chamber, replace
the splash bafe when it becomes worn.
• Do not put any of the following items into the
disposer: clam or oyster shells, drain cleaner, glass,
china, plastic wrap, large bones, metal objects,
explosive materials, extremely hot water, grease,
oil, or syrup.
• Turn the power off before attempting to clear a jam,
remove an object, or press the reset button.
• Do not insert your ngers into the disposer. Use
long-handled tongs or pliers to remove objects
from the disposer.
• Loosen any jams with the dejamming bar.
• Be certain that all persons who will operate the
disposer read the safety and operating instructions
prior to operating the disposer.
• To prevent accidents, ensure that the disposer is
turned off before you leave the area.
PROPERTY DAMAGE
• Disposers shipped from factory are not wired
for a specic voltage. Refer to the motor
connection wiring diagram in the terminal box for
voltage instructions.
• Ensure the disposer motor voltage and phase
match that of the electrical supply.
• The disposer motor wiring connection is shown in
the disposer terminal box.
GROUNDING INSTRUCTIONS
ELECTRICAL SHOCK
• All control centers and disposers must
be grounded.
• A properly fused disposer control (with a marked
“off” position) that disconnects all ungrounded
supply conductors must be installed at the
electrical supply source.
• Turn off the electrical supply to the disposer before
installing/servicing. Test the circuit with a voltmeter
or circuit tester to ensure the power is off.
• Installation must confrom to all local
electrical codes.
• Be careful not to pinch or damage the electrical
wires when installing the terminal box.
• Do not reconnect electrical current at main service
panel until proper grounds are installed.
ELECTRICAL SHOCK
• Disconnect the electrical supply before servicing
the disposer.
• Ensure the disposer and controls are
properly grounded.
FIRE HAZARD
To minimize the possibility of re, do not store
ammable items near the disposer. Do not use
or store gasoline or other ammable liquids near
the disposer.
SAVE THESE INSTRUCTIONS
5
Loading...