Insinkerator F-601R User Manual

Instant Hot Water Dispensers

Model

F-601R

The Next

Necessity

* Tested using a flow rate of 1.00 gpm;
pressure of 60 psi; pH of 7.5 ± 0.5;
temp. of 68° ± 5°F (20° ± 3°C)

** Measurement in Particles/ml. Particles
used were 0.5 - 1 microns

Base on the use of Cryptosporium parvum

*

cyst. Do NOT use with water that is
microbiologically unsafe or of unknown
quality without adequate disinfection
before or after the system. Systems
certified for cyst reduction may be used
on disinfected waters that may contain
filterable cysts. EPA Establishment #:
070595-CT-001

Job Specifications

Replacement Filter Plus

™

Submittal Sheet Specifications

• Includes 2 replacement filters for use with
InSinkErator water filtration system

• Reduces sediment, chlorine taste and odor,
Plus cysts, lead, mercury, asbestos, benzene,
atrazine, 2,4-D and other chemicals for
healthier, safer water

• Sanitary, quick-change filter cartridge
makes replacement easy. A simple twist
is all it takes!

• 6 month recommended filter
cartridge replacement

F-601R Chemical & Mechanical Reduction Filter Specifications: This cartridge provides mechanical and chemical
reduction of dirt/rust, chlorine/taste/odor, particulates, cysts, asbestos, lead, mercury, lindane, benzene, carbofuran,
p-dichlorobenzene, 2,4-D and Atrazine.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration less than or
equal to the permissible limit for water leaving the system as specified in NSF/ANSI Standards 42 and 53.

Tested and Ce rtifi ed by NSF Inte rnation al agains t NSF/ANS I Standa rd 42 and 53 fo r use in the
F-201 system f or the redu ction of Chl orine ta ste and odo r, Nominal Par ticulat e Class I, cy sts,
asbestos, lead, mercury, lindane, benzene, carbofuran, p-dichlorobenzene, 2,4-D and Atrazine.

Filter Capacity: 500 gallons, depending on local water conditions. Note that while the testing was performed under
standard laboratory conditions, actual performance may vary. For cold water use only. Systems must be installed and
operated in accordance with the Manufacturer’s recommended procedures and guidelines. See warranty card for warranty.
For service and parts, contact your local dealer or InSinkErator

Substance USEPA MCL

Nominal Particulate*

Substance

Cysts

Asbestos

Lead @ pH 6.5

Lead @ pH 8.5

Mercury @ pH 6.5

Mercury @ pH 8.5

Lindane

Benzene

Carbofuran

p-dichlorobenzene

2,4-D

Atrazine

NSF is a trademark of NSF International.
Application guidelines/Water Supply Parameters for NSF Testing: Service flow of 1.0 gpm, community or private well water supply,

water pressure of 20-125 psi, water temperature of 33˚F–100˚F. Except as noted, all testing performed at pH = 7.5 ± 0.5, Flow: 1.0 gpm,
Pressure: 60 psi, Temp: 20˚± 3˚C.

USEPA MCL

99.95% redu ction

99% reduc tion

0.015 m g/L

0.015 m g/L

0.002 mg/L

0.002 mg/L

0.0002 mg/L

0.005 mg /L

0.04 mg/ L

0.075 mg/ L

0.07 mg/ L

0.003 mg /L

Influent Challenge concentration

~

at least 10,000 particales/mL

Influent Challenge concentration

fibers gr eater than 10 µm in lengt h

(mg/L)

2.0m g/L +10 %

(mg/L)

Minimum 50,000 #L

7

10

to 108 fibers/L;

0.15 +10%

0.15 +10%

0.00 6 ±10%

0.00 6 ±10%

0.00 2 +10%

0.015 ±1 0%

0.08 ± 10%

0.22 5 ±10%

0.210 ±10 %

0.00 9 ±10%

Contact an authorized InSinkErator service agent for repairs or replacement components.

REPLACEMENT ELEMENT

Standard 42: Aesthetic Effects

Effluent
Average

2.12 mg/ L 0.05 mg/ L~Chlorine Taste & O dor

10,566,667 #/ml 171,8 33 #/ ml 360,000 #/ml 97. 88%

Standard 53: Health Effects

Influent
Average

127,000 #L

0.15 8 mg /L

0.15 4 mg /L

0.006 mg /L

0.006 mg /L

0.002 mg/L

0.014 mg/ L

0.080 mg /L

0.240 m g/L

0.19 0 mg /L

0.009 mg /L

<0.00002 mg/L

Filter Capacity

Temperature
Range

500 gallons

Incoming cold water supply
line can be from 33˚F to
100˚F (1˚C to 38˚C).
Connect to cold water
supply line only.

Pressure

Flow Rate

Shipping Weight

Dimensions

®

directly at 1-800-558-5700.

Effluent

Average Maximum Average Maximum

Average Ma ximum Average Maximum

<1 MF/L140 MF/L

<0.001 mg /L

<0.001 mg /L

0.000 mg/L

0.000 mg/L

<0.005 m g/L

1.06 3 mg/ L

0.525 mg/ L

0.012 m g/L

0.0005 mg/L

0.05 mg/ L 97. 66% 97.6 2%

1 #L

<1 MF/L

<0.001 mg /L

<0.001 mg /L

0.000 mg/L

0.000 mg/L

<0.00002 mg/L

0.005 mg /L

0.002 mg/L

0.800 mg /L

0.071 mg /L

0.0005 mg/L

1 #L >99.99%

20-125 psi

1.0 gpm

Approximately 2.5 lbs.

10-2/3"H installed, 3-1/4"W

% Reduct ion

95 .10%

% Reduct ionEffluent

>99.99%

99.72%

99.81%

99.37%

99.37%

99.33%

99.34%

89.26%

94.35%

67.15 %

85.27%

98.98%

99.03%

96.05%

96.32%

97.33%

98 .74%

99.64%

99.76%

62.63%

93.84%

94.48%

94.77%

Pressure: 20 -125 psi
Temperature: 33-100°F
Flow rate: 1.0 gpm
Capacity: 500 gallons

Min. Required

Reduction

>50%

>85%

Min. Required

Reduction

>99.95%

>99%

0.010 m g/L

0.010 m g/L

0.002 mg/L

0.002 mg/L

0.0002 mg/L

0.005 mg /L

0.04 mg/ L

0.075 mg/ L

0.07 mg/ L

0.003 mg /L

NSF

Report

J-00029741

J-00029739

NSF

Report

J-00031000

J-00029743

J-00031399

J-00029746

J-00029747

J-00029748

J-00029753

J-00029751

J-00029750

J-00029749

J-00029754

J-00029752

USA
1-800-558-5700

www.insinkerator.com

Canada

1-800-561-1700

www.insinkerator.ca

HWD427-12F-45-12 Printed in USA

The Emerson logo is a trademark

and a service mark of Emerson Electric Co.

InSinkErator may make improvements and/or changes

in the specifications at any time, in its sole discretion,

without notice or obligation and further reserves the

right to change or discontinue models.

©2012 InSinkErator, a business unit of

Emerson Electric Co. All Rights Reserved.