InSinkErator F2000 Specs
The Next
Necessity
Instant Hot Water Dispensers
Model
F-1000S Filtration System
A water filtration system exclusively designed for
™
InSinkErator instant hot water dispensers
Dimensions
rf mo dloc
12-1/2
retaw telni
"
2-1/4
ot tecuaf
"
Job Specifications
Submittal Sheet
• Reduces particulates, chlorine taste and
odor for clean, refreshing taste
• Quick-connect fittings guarantee
easy installation
• Sanitary, quick-change filter cartridge
makes replacement easy. A simple twist
is all it takes!
• Automatically shuts off water when filter
cartridge is replaced
• Replace every 6 months at the rated
capacity or if a noticeable reduction in
Specifications
Filter Capacity
Temperature
Range
Pressure
Flow Rate
Shipping Weight
500 gallons
Incoming cold water
supply line can be
from 33˚F to 100˚F
(1˚C to 38˚C).
Connect to cold water
supply line only.
30-120 psi
0.75 gpm
Approximately 2.2 lbs.
flow rate occurs
Warranty:
1-year parts and in-home service*
(excluding replaceable filter cartridge)
* The complete InSinkErator warranty is included in the Care & Use
booklet packed with each unit.
F-1000 Cartridge (included with this system) Chemical & Mechanical Reduction Filter Specifications:
This cartridge provides mechanical and chemical reduction of chlorine taste & odor and particulate class III.
Tested & Cer tified by N SF Internationa l against N SF/ANSI Standa rd 42 in the following
InSinkE rator Sys tems Only: GN1100, HC1100, GN2200, HC2 200, GN2215, HC2215,
H3300 o r HC330 0 for the red uction of c laims sp ecifie d on the Performan ce Data Sheet.
For system s using two handle HC m odel faucets, op erate only one hand le at a time.
Filter Capacity: 500 gallons, depending on local water conditions. Note that while the testing was performed under
standard laboratory conditions, actual performance may vary. Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before or after the system. For cold water use only. Systems must be
installed and operated in accordance with the Manufacturer’s recommended procedures and guidelines. See warranty
card for warranty. For service and parts, contact your local dealer or InSinkErator
2.1 mg/L 2.0 mg/L ± 10%
Nominal
Particulate Class III,
≥5 µm to <15 µm
Application guidelines/Water Supply Parameters for NSF Testing: Service flow of 0.75 gpm, community or
private well water supply, water pressure of 20-120 psi (138-827 kPa), water temperature of 33˚F–100˚
Refer to the Performance Data Sheet for InSinkErator Filter System Model F-1000S
Replacement Cartridge: F-1000
Contact an authorized InSinkErator service agent for repairs or replacement components. Replacement filters
F-1000 and F-2000 can be ordered by calling 800-558-5700, visiting shop.insinkerator.com, or by contacting
an authorized InSinkErator reseller.
270,000 pts/mL
At least 10,000
particles/mL
0.06 mg/L 97.0% ≥ 50%
82 pts/mL 99.9% ≥85%
Pressure: 30-120 (207-827 kPa) psi
Temperature: 33
Flow Rate: 0.75 gpm
Capacity: 500 gallons
®
directly at 1-800-558-5700.
º
F - 100ºF
J-00082587
J-00119308
F Except as noted, all testing performed at pH = 7.5 ± 0.5, Flow: 0.75 gpm, Pressure: 60 psi, Temp: 20˚± 3˚C.
USA
1-800-558-5700
www.insinkerator.com
Canada
www.insinkerator.ca
HWD439-13D-45-10 Printed in USA
The Emerson logo is a trademark
and a service mark of Emerson Electric Co.
InSinkErator may make improvements and/or changes
in the specifications at any time, in its sole discretion,
without notice or obligation and further reserves the
right to change or discontinue models.
©2013 InSinkErator, a business unit of
Emerson Electric Co. All Rights Reserved.
Loading...