Insignia NS-LT500P-1 User Manual

NS-LT500P-1_15-0329_QSG_V1_EN.ai 1 4/9/2015 9:06:20 AMNS-LT500P-1_15-0329_QSG_V1_EN.ai 1 4/9/2015 9:06:20 AM
V1
FINAL
FOR PRINT
Flat size (W×H): 209.2 × 148 mm. Final folded size: 104.6 × 148 mm.
Quick Setup Guide | NS-LT500P-1
Refrigerator Filter
Congratulations on your purchase of one of the highest performing water lters on the market today. Insignia lters use a high-grade coconut carbon that has 50% more micro-pores than standard carbon. They also use fewer high-compression binders, giving you the best water ltration possible.
PACKAGE CONTENTS
• Refrigerator lter(s) (1 pack)
Quick Setup Guide
GENERAL INSTALLATION GUIDELINES
• It is normal for black carbon nes (particles) to appear on the outside of your lter. This happens when the lter is jarred in shipping. It is safe, simply wipe it o.
Connections on our lters are larger in size to prevent leakage. This
might require more hand leverage to install.
INSTALLING THE WATER FILTER
1 YOU MUST SOAK your new lter in water for 15 minutes prior to
installing it in your refrigerator to remove air from the carbon block.
2 Twist the old lter a quarter-turn counter-clockwise. 3 Pull the lter straight down and discard. 4 Push the new lter up into the refrigerator until it stops. 5 Twist the lter a quarter-turn clockwise. 6 Run about two to three gallons of water through your refrigerator’s water
dispenser to remove air and loose carbon pieces. The water may be cloudy and sputter until the air is removed.
7 Reset your “change lter” indicator (if your refrigerator has one). See
below.
RESETTING YOUR CHANGE FILTER INDICATOR
Note: These are the most common lter reset instructions. If the instructions don’t
work for your refrigerator brand, see the documentation that came with your refrigerator.
REFRIGERATOR BRANDLGINSTRUCTIONS
Press and hold the reset button for three seconds.
Before using your new product, please read these instructions to prevent any damage.
NS-LT500P-1_15-0329_QSG_V1_EN.ai 2 4/9/2015 9:06:28 AMNS-LT500P-1_15-0329_QSG_V1_EN.ai 2 4/9/2015 9:06:28 AM
TROUBLESHOOTING STORAGE AND MAINTENANCE
PROBLEM
My refrigerator is not dispensing water
My water dispenser is dripping
My water is cloudy or contains black carbon pieces
My new lter is making noises or sputtering
My water tastes bad
SOLUTION
• Make sure that you soaked your lter in water for 15 minutes before installing.
• Make sure that the lter is securely connected to the receiver. Do not use tools to tighten the lter in place.
• Make sure that the water line to the refrigerator is turned on. The valve must be completely open for the refrigerator to receive water.
• Make sure that the refrigerator door is closed or the dispenser will not work.
• A few drops are normal. If the water is dripping constantly, have a service technician check your refrigerator’s water valve.
• Cloudy water is caused by microscopic air bubbles. Run two to three gallons of water from your dispenser to clear the air bubbles out.
• Black carbon pieces in the water are normal and appear with all carbon lters. Run two to three gallons of water through your dispenser to remove loose carbon pieces.
• Make sure that you soaked your lter in water for 15 minutes before installing.
• Noises and sputtering are caused by trapped air pockets. Run two to three gallons of water from your dispenser to push the air out.
• If you do not use your water dispenser for more than four days, run two gallons of water through the dispenser before using it.
• Make sure that you replace your lter every three to six months to prevent bacteria growth.
• Replace your lter every three to six months to prevent bacteria and fungus growth in your lter, supply lines, and storage tank.
• Stored lters do not expire. Keep your unused lters in a cool, dark, and dry place until you need them.
• If you do not use your water dispenser for more than four days, run two gallons of water before using it to prevent bad tasting water.
ONE-YEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com
CERTIFICATIONS:
This NS-LT500P-1 is Tested and Certied by NSF
International against NSF/ANSI Standard 42 for materials
COMPONENT
INSIGNIA is a trademark of Best Buy and its aliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richeld, MN 55423 U.S.A. ©2015 Best Buy. All rights reserved. Made in China
and structural integrity requirements.
V1 ENGLISH 15-0329
Loading...