Insignia NS-GWU1303-C User Manual
QUICK SETUP GUIDE
Wii U™ Controller Charge Station
NS-GWU1303-C
Package contents
• Wii U controller charge station • Wii remote rechargeable
• AC adapter batteries (2)
• Quick Setup Guide
Installing the batteries into the Wii™ Remotes:
1 Remove all silicone skins or jackets on the Wii remotes in order to
access the battery compartment, then remove any batteries in the
compartment.
2 Insert the battery pack into the battery compartment with the front
end rst, then snap the battery pack into the battery compartment.
Setting up the Wii U Controller Charge Station:
1 Connect the supplied AC adapter into an appropriate electrical outlet.
Using the Wii U Controller Charge Station
Wii Remotes:
1 Remove all jackets, silicone skins, and the Motion Plus adapters from
the remotes. The remotes will not charge with these on. Align the Wii
Remote hand strap with the groove in the charge station to prevent
the hand strap from interfering with charging.
Cautions
• You must use the included AC adapter to power the charge station.
• Do not disassemble any of the components. Refer all services to
qualied personnel only.
• Do not place or store the product in a humid area and do not expose
it to water or rain.
• Use the product only as instructed. Read all instructions before
operating the product.
• Failure to follow these directions may void the warranty.
• For use with Wii U controllers and peripherals.
Features
• Designed to charge all Wii U controllers, including the Wii U
GamePad, Pro Controller, and Wii Remotes.
• LED Indicators provide charging status notication. Red indicates
charging in process, green indicates charging complete.
Before using your new product, please read these instructions to prevent any damage.
Original
battery cover
2 Insert the AC adapter DC plug into the DC IN 5V jack on the back of the
Battery
pack
Wii U Controller Charge Station (see below):
2 When inserting the Wii Remote into the charge station, the charge
status indicator glows red while the battery pack is recharging. When
SY
NC
recharging is complete, the charge status indicator glows green.
3 Place the Wii U Controller Charge Station on a at and stable surface
and start charging the controllers.
Red: Charging in process
Green: Charging complete
Wii U GamePad:
1 Place the Wii U GamePad into the front charging port on the station
as shown below.
2 The Battery LED on the Wii U GamePad lights up orange during
charging and will turn o when the battery is fully charged.
Wii U Pro Controller:
1 Locate the mini USB charge cable on the bottom of the Wii U
Controller Charge Station.
2 Insert the mini USB charge connector into the Wii U Pro Controller.
3 The charge status indicator LED will light up (orange) on the Pro
Controller while charging and turn o when fully charged.
Specications
Battery pack: Ni-MH battery pack × 2
AC Adapter: input 110V-220V
AC adapter: output DC 5V 2A
AC adapter cable length: 1 meter
Input voltage: 100-220V ~ 60Hz
Output power: 5V at 2A
Legal notices
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/T V technician for help.
Warn ing : Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
“Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.”
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment.
“Cet équipement est conforme à l'exposition aux rayonnements IC limites établies pour un
environnement non contrôlé.”
One-year limited warranty
Visit www.insigniaproducts.com for details.
Contact Insignia:
For customer service, call 1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
Wii and Wii U are trademarks of Nintento of America, Inc.
INSIGNIA is a trademark of Best Buy and its aliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V1 ENGLISH 14-0065
Loading...