Insignia NS-CAHBTEB01 User Manual
OFF/ON
O
NS-CAHBTEB01_15-0448_QSG_V2_EN.ai 1 4/22/2015 11:12:35 AMNS-CAHBTEB01_15-0448_QSG_V2_EN.ai 1 4/22/2015 11:12:35 AM
V2
FINAL
FOR PRINT
Final flat size: 304.8 x 177.8 mm
Final fold size: 76.2 x 177.8 mm
Quick Setup Guide | NS-CAHBTEB01
Bluetooth Headset
PACKAGE CONTENTS
• Bluetooth Headset
• USB charging cable
• Earbuds (small and large)
• Quick Setup Guide
FEATURES
• High-quality stereo sound from Bluetooth 4.0 enabled devices
• Battery lasts 12 hours (talk), 10 hours (music)
• Inline controls easily adjust audio
• Curved design ts comfortably around the neck
F/ON
F
O
Before using your new product,
please read these instructions to prevent any damage.
Rewind/Skip back
Fast forward/Skip forward
Charging port
Neck strap
Earbud (R)
Power switch
Microphone
Earbud (L)
Call button/LED indicator
Volume down
Volume up
Play/Pause
CHARGING YOUR HEADSET
A tone sounds (every 60 seconds) and the LED
ashes red when your headset battery is low.
• Connect the USB charging cable from your
headset’s charging port to a USB port.
N
O
F/
F
O
PAIRING YOUR HEADSET
Pairing your rst Bluetooth device
1 Slide the power switch to ON. The LED blinks red
and blue and the headset enters pairing mode.
2 Make sure that your Bluetooth device is within
33 ft. (10 m) of your headset.
3 Turn on your Bluetooth device, turn on Bluetooth,
then set your device to pairing mode. For more
information, see the documentation that came
with your Bluetooth device.
4 On your Bluetooth device, select
NS-CAHBTEB01. The LED lights blue and a tone
sounds when your headset pairs to your
Bluetooth device.
Manually pairing your Bluetooth device
1 Press and hold (call) to enter pairing mode. The
LED blinks red and blue.
2 Make sure that your Bluetooth device is within
33 ft. (10 m) of your headset.
3 Turn on your Bluetooth device, turn on Bluetooth,
then set your device to pairing mode. For more
information, see the documentation that came
with your Bluetooth device.
4 On your Bluetooth device, select
NS-CAHBTEB01. The LED lights blue and a tone
sounds when your headset pairs to your
Bluetooth device.
Pairing two devices
1 Pair your headset to your secondary Bluetooth
device rst. See "Pairing your rst Bluetooth
device" for instructions.
2 Press and hold (call) on your Bluetooth headset
to enter pairing mode.
3 Connect your primary Bluetooth device to your
Bluetooth headset. See "Manually pairing your
Bluetooth device" for instructions.
4 Re-pair your secondary Bluetooth device to your
Bluetooth headset. See "Manually pairing your
Bluetooth device" for instructions.
Note: When connected to two phones, the
headset calling functions will work with the
primary phone.
Disconnecting and reconnecting your paired
device
Your headset remembers up to six Bluetooth devices
and will turn o after three minutes if it is not paired
to a Bluetooth device.
To disconnect…
Turn o your headset
To reconnect…
Turn on your headset .Your headset
searches for the last connected
Bluetooth device and reconnects.
NS-CAHBTEB01_15-0448_QSG_V2_EN.ai 2 4/22/2015 11:12:43 AMNS-CAHBTEB01_15-0448_QSG_V2_EN.ai 2 4/22/2015 11:12:43 AM
To disconnect…
Move the Bluetooth
device out of range
Turn o your Bluetooth
device
Turn o Bluetooth on
your Bluetooth device
Connect your Bluetooth
device to another
Bluetooth device
To reconnect…
Make sure your Bluetooth device is
within 33 feet of your headset.
Turn on your Bluetooth device, then
make sure Bluetooth is on.
Turn on Bluetooth on your Bluetooth
device.
Disconnect your Bluetooth device
from the other Bluetooth device,
then set your device to pairing
mode. Select “NS-CAHBTEB01” on
your Bluetooth device.
Note: If a device does not automatically reconnect,
you may need to reselect “NS-CAHBTEB01” on your
Bluetooth device.
WEARING YOUR HEADSET
USING YOUR HEADSET
Making phone calls
Note: When your headset is connected to two
Bluetooth devices, calling functions work with the
primary Bluetooth device (the one that is connected
second or made the last outgoing call).
• To make a call, use your phone’s controls, then
select the headset as the audio source.
• To redial the last number on your primary phone,
press (call) twice.
• To answer an incoming call, press (call).
Note: Your headset vibrates when there is an
incoming call.
• To switch audio between your headset and phone,
use your phone’s controls.
• To reject an incoming call, press and hold (call) for
two seconds.
• To end a call, press (call) one time.
Call waiting
• To switch to an incoming call, press (call) twice
while speaking on an active call.
• To switch between two active calls, press (call)
twice.
• To end both calls, press (call).
Begin playback on your Bluetooth device.
• To play audio, press .
• To skip to the next track, press
• To skip to the previous track, press
.
.
• To fast forward, press and hold .
• To rewind, press and hold .
SPECIFICATIONS
• Average charging time: 1.5 - 2 hours
• Operating time: Talk - 12 hours / Music - 10 hours
• Working distance: Up to 33 ft. (10 m)
• Battery: Lithium 200mAh/3.7V
SAFETY INFORMATION/CAUTION
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, maybe cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
TROUBLESHOOTING
Problem
No sound or low volume
Cannot connect with Bluetooth
Bluetooth device keeps unpairing
“NS-CAHBTEB01” does not appear on my
Bluetooth device
No Power
harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent form that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
RSS-Gen & RSS-210 statement:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
Solution
• Make sure that your Bluetooth device is turned on, Bluetooth is turned on, and
“NS-CAHBTEB01” is selected.
• Turn up the volume on your headset and Bluetooth device.
• Make sure that your Bluetooth device is not muted.
• Make sure that your headset and Bluetooth device are not paired to other devices.
• Shorten the distance between your headset and Bluetooth device.
• Turn your devices o, then on. Re-pair your headset and Bluetooth device.
• Make sure that your headset and Bluetooth device are not paired to other devices.
• Make sure that your Bluetooth device supports the HSP, SFP, A2DP, or AVRCP Bluetooth
protocol.
• Make sure that you have selected “NS-CAHBTEB01” on your Bluetooth device.
• Shorten the distance between your headset and your Bluetooth device.
• Recharge your headset and Bluetooth device's batteries.
• Shorten the distance between your headset and Bluetooth device.
• Put your headset into pairing mode, then refresh your list of Bluetooth devices. For
more information, see the documentation that came with your Bluetooth device.
• Make sure your Bluetooth headset is charged.
• Make sure your Bluetooth headset is turned ON.
susceptible d'en compromettre le fonctionnement.
RSS-102 Statement:
This equipment complies with Industry Canada radiation exposure limits set
forth for an uncontrolled environment.
Cet équipement est conforme à l'exposition aux rayonnements Industry Canada
limites établies pour un environnement non contrôlé.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
1-877-467-4289 (U.S. and Canada)
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies. Registered in some
countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2015 Best Buy. All rights reserved. Made in China
V2 ENGLISH 15-0448
Loading...