Innotek SD-2100, SD-2200 Quick Start Manual

Run the containment wire around the property as outlined in your plan.
Step 3 Lay Out the Fence Wire
Step 2 Install the Wall-mount transmitter
Step 1 Design Y our Fence
Quick Start Guide SD-2100, SD-2200
Have the local utility companies mark your underground lines. On a sheet of paper, draw your house and yard. Draw a line around your property that repre­sents the containment area for your dog.
Most people find that the inside of an exterior wall of a garage or basement is ideal.From the sample layouts, you can see the twisted wire running from the house attaches directly to the transmitter.
Invisible Technologies,Inc. 1-800-826-5527 www.innotek.net
2100218-2
Step 4 Final Connections
Splice the containment loop wires to the twisted wire using the supplied water­proof splices.Connect the other end of the twisted wire to the wall-mount trans­mitter. Plug in the AC adapter, connect it to the transmitter, and turn it on. The green light should illuminate on the transmitter indicating a successful loop. Charge your collar receiver by placing it in the receiver cradle located on top of the transmitter.
1.
Boundary Wire
Splice
To wall-mount transmitter
Deluxe & Premium In-ground Pet Fencing Systems
Boundary Wire
10’
10’
Buried Cable
90˚
IMPORTANT ADVICE
1. Read the complete manual and follow all directions. This includes the Training and Troubleshooting Guide.If you have any questions, please call 1-800-826-5527.
2.This device is intended for use only on dogs.Never attempt to use it for any purpose not described in this manual.
3.Never perform set-up procedures while the collar is on your dog.
4. Any collar worn for extended periods can cause a condition similar to bedsores, known as Pressure Necrosis.To reduce the possibility, you must do the following:
• Never leave the collar on the dog for more than 12 hours per day.
• Check the fit to prevent excessive pressure;you should be able to insert one finger between the collar strap and your dog’s skin.
• Examine the dog’s neck daily for any signs of a rash or a sore.
• Wash the dog’s neck area and the probes of the collar weekly with a damp cloth.
• If the condition persists beyond 24 hours, see your veterinarian.
5. Always use the rubber insulators between the collar strap and probes to provide insulation in damp conditions.
6. Other collars and metal tags should be removed as they may interfere with proper operation.
7. Do not attempt to dismantle or repair any components of this system;doing so will void the warranty in full.The computerized circuitry should be serviced only by an authorized expert.
8.Realize that because dogs have unique tempera­ments, there is no way of knowing how your dog will react to the introduction of a containment system. For the safety of your dog, a long lead should be used during initial training so you have control of the situation.
9.If you have reason to believe that your dog may pose a danger to others, harm itself, or react adversely to the collar, do not rely solely on this product to train your dog. If your dog shows signs of growling, snarling or biting while using the collar, stop immediately. Aggression in dogs has many causes.We recommend that you consult a knowl­edgeable professional dog trainer or animal behaviorist with experience with aggressive dogs if your dog has shown any of these characteristics.
10.Occasionally, a dog cannot be trained to respond to a containment collar.Sometimes even a properly trained dog may disobey a command. Therefore, Invisible Technologies, its distributors, and dealers cannot guarantee that the system will in all cases keep the customer’s animal from disobeying commands.
WE CARE. CALL US FIRST. 1-800-826-5527
LIMITED LIFETIME WARRANTY
Invisible Technologies warrants to the original retail pur­chaser, that Innotek brand products will be free from defects in material and workmanship, under normal use, for a period of one year from the date of the original retail purchase. This Limited Warranty excludes: accidental damage due to dog chews; lightning damage where an INNOTEK lightning protection component is not in use (in­ground pet fencing systems); or neglect, alteration and misuse.
Invisible Technologies offers several product exchange options during the warranty period. If service is required, call 1-800-826-5527 to discuss the service plan that best serves your needs. Costs are dependent on the process­ing time and the desired shipping options. Please do not return this product to your retailer.
After one year from date of original retail purchase, we will repair, replace or upgrade your product at a fixed rate based on the component.
Invisible Technologies, Inc., shall not be liable or responsi­ble for any incidental or consequential damages resulting from the use of the product or caused by any defect, fail­ure or malfunction of the product, whether a claim is based upon warranty, contract, negligence or otherwise.
FREE Professional Training Support
Additional behavior or training issues?
Looking for the best way to get a well-behaved dog?
Just call our FREE Professional Training Support hotline
at 1-800-364-3362 and speak with the professionals
at Dogstar Training.
Visit www.partnersinbehavior.com
Watch the training video and follow the training steps outlined in the separate Training and Troubleshooting Guide.Your dog may respond immediately to the train­ing, however, continue to follow the enclosed Training Guide to fully train your dog.The convenience that your new fence offers plus the added safety for your dog are well worth the time invested.
Step 8 Train Your Dog
Step 7 Bury Fence Wire
Step 6 Test Y our Fence
Quick Start Guide (continued) SD-2100, SD-2200
Set your FIELD WIDTH ADJUSTMENT KNOB to the 9 o’clock position.Using the supplied test light, walk the dog’s collar up to the fence wire. Listen for the warn­ing tone and look for the test light to light. Try a number of different places around the fenced area to verify the range is consistent.
Dig the trench 3” deep with a flat edge spade. Or, it is faster to use a gas-pow­ered edger.Digging the trench at an angle helps keep the wire in the ground as you place it. Place flags at edge of selected boundary field where the warning tone is first heard, NOT at wire.
2. 3.
Step 5 Charge Collar
Position the collar receiver in the charging cradle located on the top of the wall transmitter. Orient the light on the collar receiver toward the end of the charging cradle marked with an arrow and identified on the label.
collar receiver light to this end
1. Field Width Adjustment Control
Loading...
+ 2 hidden pages