Ing Sumetzberger RP 44873 User Manual
RFID 2000 (Radio Frequency Identification)
Architect’s User’s Owner’s Guide
Vers.1.2
Note:
Company Sumetzberger reserves the right to do modifications on their products, which serve the
technical development of the products. These modifications are not necessarily recorded in each
particular case. This documentation and the contained information are recorded and arranged with the
necessary diligence, but company Sumetzberger takes no guarantee for printing errors or other faults
or resulting damages. The brand and products named in this documentation are trademarks or registered trademarks of the particular title holder.
Ing Sumetzberger GmbH
Leberstraße 108
A-1110 Vienna
Telephone
Fax +43.(0)1.74035 300
E-mail (Technical support) pt.technics@sumetzberger.at
E-mail (Sales) pt.sales@sumetzberger.at
Homepage www.sumetzberger.com
© Copyright 2011 Ing Sumetzberger GmbH
+43.(0)1.74035 0
RFID 2000 (Radio Frequency Identification)
1 Data sheets
RFID 2000................................................................................................1
Code Tag..................................................................................................2
Antenna 110.............................................................................................3
Antenna 160.............................................................................................4
2 Installation
RFID2000.................................................................................................5
Antenna ...................................................................................................6
Carrier 160 ................... ............................................................................7
Flip top carrier 110................................. .... ... .. .. .. .. .. .. .... ... .. .. .. .. .. .... .. ... .. .. ..8
Application examples of RFID2000 units .............................. .......................9
CONTENTS
3 Cabling
General-System cable................................. ... .... .. .. .... .. .. ..... .. .... .. .. .... ... .. ....10
Power supply with filter modul ...................................................................11
SCB2000 with RFID and 1 Antenna.............................................................12
SCB2000 with RFID and 3 Antenna.............................................................13
4 EU-Conformity Declaration
5 FCC-Registration
FCC Statement..........................................................................................15
FCC Confidentiality Request .......................................................................16
6 User Instruction Manual
General Safety Instructions........................................................................17
Label for devices....................................................... ................................18
General ....................................................................................................19
Keyboard..................................................................................................20
User numbers.................................................................... .......................20
Making a transit........................................................................................21
Arrival Signal ....................................... .. .. ..... .. .. .. .. .. .. .. ..... .. .. .. .. .. .. .... ... .. .. ..22
Special Codes ...................................... .....................................................23
Security....................................................................................................24
DCU Instruction Special Codes ...................................................................25
Data sheets
RFID 2000
Data sheets 1 - 1
8.3.11
RFID 2000 Vers.1.2
Model
Manufacturer
Use
Function
Technical description
RFID 2000
Sumetzberger GmbH
Leberstraße 108; 1110 Vienna
Extension card: Code Tag
By equipping the carrier with passive transponder (no bat tery), called code
tags on both ends, all carries can receive there own identification number
and so they can be assigned to a determinate station. The return to this
"homestation" is possible without entering the address.
Therefor only carriers can be used which are registered to the system and
not registered carriers can’t be infiltrated in the system.
Follow stations can be equipped: DRT110, DRT Front 110, E3S110
MSS110/160 DST160, DST-END160.
The RFID 2000 board is a four antenna reader for Philips HITAG2 Chips.
The main controller is a PIC16F873A running with 16 MHz, which multiplexes four tuning devices (Philips HTRC-110 ) and is connected with an I²C
bus to the main board. Each antenna has an own tuning device (Philips
HTRC-110), which produces the 125 kHz antenna signal and reads the
chips.
Technical data
Picture:
Sending frequency: 125kHz Exciting frequency: 125kHz
Code Tag
Data sheets 1 - 2
8.3.11
RFID 2000 Vers.1.2
Model
Item
Frequency
Power supply
Data storage
Programming
Mechanical dimensions
Temperature
Protection class
"Code Tag" (passive Transponder)
Identification Transponder for the use in contactless applications
125kHz operating frequency
Data transmission and supply energy via RF link, no internal battery
The code tag is dedicated for the use in secure access systems (transponder and reader have to identify each other). The transponder requires no
internal power supply; it derives its power from magnetic component of
the RF carrier frequency generated by the reader antenna.
EEPROM; guaranteed ten years of non-volatile data retention
Programming via carrier programming unit. More than 100.000 erase/
write cycles possible.
12x6x3mm (refer to pic)
Operating temperature:- 40°C bis 85°C
Storage temperature:- 55°C bis 125°C
IP67
Casting material
Picture
epoxy resin
Antenna 110
Data sheets 1 - 3
8.3.11
RFID 2000 Vers.1.2
Model
Manufacturer
Use
Technical data
Accessories
Picture:
Antenna 110
Sumetzberger GmbH
Leberstraße 108; 1110 Vienna
To identify the coded carrier
φ110mm
Antenna holder: RP44965
Antenna 160
Data sheets 1 - 4
8.3.11
RFID 2000 Vers.1.2
Model
Manufacturer
Use
Technical data
Picture:
Antenna 160
Sumetzberger GmbH
Leberstraße 108; 1110 Vienna
To identify the coded carrier
φ160mm
Installation
RFID board plugged to DCB
RFID2000
The installation of the RFID2000 on the SCB2000 have to done as follows
Plug the RFID circuit board in the extension board of the SCB2000 circuit board.
Pug the RFID board in the extension board of the
SCB2000 circuit board.
Installation 2 - 5
8.3.11
RFID 2000 Vers.1.2
Installation 2 - 6
X1
RFID 2000 Vers.1.2
Antenna
Installation of the Antenna
The Installation of the Antenna on the SCB2000 - RFID2000 unit have to done as follows
The antenna 110 and 160 are installed as follows.
Remove the plug X1 from the RFID2000 circuit
board (picture1 ) and put the plug from the antenna
in the RFID2000 (picture 2).
Attention!
The white side of the plug from the antenna
have to be on the upper side.
8.3.11
Loading...