Inglis ATW4675EW, ATW4675YQ, ATW4676BQ, ITW4600YQ, ITW4700YQ Owner's Manual

...

TOP-LOADING

LAVEUSE À CHARGEMENT

WASHER

USE AND CARE GUIDE

Table of Contents

WASHER SAFETY ............................................................ 2

WHAT’S NEW UNDER THE LID? .................................... 3

CONTROL PANEL AND FEATURES ...............................4

CYCLE GUIDE .................................................................. 6

USING YOUR WASHER ................................................... 7

WASHER MAINTENANCE ............................................... 9

TROUBLESHOOTING .................................................... 11

WARRANTY .................................................................... 15

ASSISTANCE OR SERVICE ....................... BACK COVER

PAR LE DESSUS

GUIDE D’UTILISATION ET

D’ENTRETIEN

Table des matières

SÉCURITÉ DE LA LAVEUSE .........................................16

QUOI DE NEUF SOUS LE COUVERCLE? .................... 17

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES .............................................. 18

GUIDE DE PROGRAMMES ........................................... 20

UTILISATION DE LA LAVEUSE ..................................... 21

ENTRETIEN DE LA LAVEUSE .......................................24

DÉPANNAGE .................................................................. 26

GARANTIE ...................................................................... 31

ASSISTANCE OU SERVICE. .... COUVERTURE ARRIÈRE

Para una versión de estas instrucciones en español, consulte la página de “Ayuda o servicio técnico”.

W10420470C W10420471C - SP

WASHER SAFETY

WHAT’S NEW UNDER THE LID?

Your new washer will operate differently than your past agitator-style washer.

Lid Locked

To allow for higher spin speeds, the lid will lock and the Lid Locked light will turn on. When this light is lit, the lid is locked and cannot be opened. When this light is blinking, the washer is paused. When this light is off, the lid can be opened. After a cycle is started, water will enter washer and then lock. If you need to open the lid to add a garment after this point, you must press START/Pause/ Unlock Lid and wait for the lid to unlock. The lid will only unlock after washer movement has stopped. Depending on when in the cycle you try to pause, it may take several seconds to several minutes for the lid to unlock. Press START/Pause/Unlock Lid to resume the cycle.

Sensing

This washer will perform a series of spins to check for load balance. During this time, a series of clicks and a whirring noise signal that sensing technology is determining if there is an off-balance load.

Sounds

At different stages of the wash cycle, you may hear sounds and pauses that are different from those of your previous washer. For example, you may hear a clicking and hum at the beginning of the cycle as the lid lock goes through a self-test. There will be different kinds of humming and whirring sounds as the agitator tests for load balance or moves the load. And, sometimes, you may hear nothing at all as the washer allows time for clothes to soak.

Spray Rinse

Select cycles default to a spray rinse. During these cycles, you will hear water enter the washer as the tub spins, allowing the rinse water to penetrate clothes. Check the “Cycle Guide” for details.

IMPORTANT:

■ After the washer basket lls to the selected water level, the lid must be closed before the wash cycle can start.

If lling stops with the lid open, close lid and press START button.

■ Fabric Softener option must be set to Yes to ensure fabric softener dispenses at the correct time (on some models).

CONTROL PANEL & FEATURES

1 3

Not all features and options are available on all models.

LOAD SIZE

Select the setting most suitable for your load. Extra Small or Small (depending on model) will add a low amount of water for smaller loads and Large will add the most amount of water for large or bulky loads. Items need to move freely. Tightly packing can lead to poor cleaning performance, and may increase wrinkling and tangling.

WASH TEMP or TEMPERATURE

Temperature senses and maintains uniform water temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric and soils being washed. For best results and following the garment label instructions, use the warmest wash water safe for your fabric.

■ On some models and cycles, warm and hot water may

be cooler than your previous washer.

■ Even in a cold and cool water wash, some warm

water may be added to the washer to maintain a minimum temperature.

Appearance may vary.

FABRIC SOFTENER (on some models)

This option can be added to most cycles and must be set to YES if using fabric softener during a cycle. It ensures that fabric softener is added at the correct time in the rinse for even distribution.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer. Knob does not advance during the progress of the cycle, see cycle status lights for each stage of the process. See “Cycle Guide” for detailed descriptions of cycles.

START/PAUSE/UNLOCK LID BUTTON

Press to start the selected cycle; press again to pause the cycle and unlock the lid.

NOTE: If the washer is spinning, it may take several minutes to unlock the lid. Press and hold for 3 seconds to cancel a cycle.

421

CYCLE STATUS LIGHTS

The Cycle Status Lights show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from traditional washers.

FILL

When the START/Pause/Unlock Lid button is pressed, the washer will ll to the selected water level. If the lid is closed when the machine is done lling the lid will lock and the machine will begin operation.

If the lid is open when the water stops entering the machine, the cycle will not begin until the lid has been closed and the START/Pause/Unlock Lid button is pressed. If the cycle has not been started within 10 minutes of the water lling the washer, the washer will pump out the water.

NOTE: Avoid opening lid during sensing phase. The sensing process will start over when the washer is restarted. The ll light may also come on during the Soak and Wash portions of the cycle. This is normal. To restart the washer after the lid has been opened press start.

WASH

You will hear the agitator moving the load. The motor sounds may change at different stages in the cycle. The wash time is determined by the selected soil level.

RINSE

You will hear sounds similar to the wash cycle as the washer rinses and moves the load. You may hear the motor turning on briey (short hum) to move the basket while lling. Fabric softener will be added if the Fabric Softener knob was set to YES.

Some cycles use spray rinsing. After draining and spinning out wash water, the washer will continue to spin and spray in rinse water for the entire rinse time.

FINAL SPIN

The washer spins the load at increasing speeds for proper water removal, based on the selected cycle and spin speed.

CYCLE COMPLETE

Once the cycle is complete, this light will come on. Remove the load promptly for best results.

LID LOCKED

To allow for higher spin speeds, the lid will lock and the Lid Locked light will turn on. When this light is on, the lid is locked and cannot be opened. When this light is blinking, the washer is paused. When this light is off, the lid can be opened.

If you need to open the lid, press START/ Pause/Unlock Lid. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Press START/Pause/ Unlock Lid again to resume the cycle.

CYCLE GUIDE

For best fabric care, choose the cycle that best ts the load being washed. Not all cycles and options are available on all models.

Items to wash: Cycle: Wash

No-iron fabrics, cottons, perm press, linens, synthetics

Cottons, linens, towels, sheets, and mixed garment loads

Cottons, linens, sheets, and mixed garment loads

Machine-wash silks, hand-washed fabrics

Small loads of items labeled “handwash”: undergarments, bras, silks

Swimsuits and garments requiring rinsing without detergent

Hand-washed garments or dripping wet items

NOTE: Be sure to set Fabric Softener knob to YES, if adding fabric softener to load (on some models). *All rinses are cold.

Casual

Regular

Casual

Medium

Casual

Light

Normal

Extra Heavy

Normal

Regular

Normal

Light

Delicate

Regular

Delicate

Light

Handwash Hot

Rinse/Spin Cold rinse only High Combines a rinse and high speed spin for loads requiring

Drain/Spin N/A High This cycle uses a spin to shorten drying times for heavy

Temperature*:

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Hot

Warm

Cool Cold

Warm

Cool Cold

Spin

Speed:

Low Use this cycle to wash normally soiled loads of no-iron

fabrics such as sport shirts, blouses, casual business clothes, permanent press, and blends.

Low Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent press, and blends.

Low Use this cycle to wash lightly soiled loads of no-iron

fabrics such as sport shirts, blouses, casual business clothes, permanent press, and blends.

High Use this cycle for heavily soiled cottons and mixed fabric

loads. This cycle features a spray rinse. Use this cycle for cleaning the interior of the washer. See “Washer Care.”

High Use this cycle for normally soiled cottons and mixed fabric

loads. This cycle features a spray rinse.

High Use this cycle for lightly soiled cottons and mixed fabric

loads. This cycle features a spray rinse.

Low Use this cycle to wash soiled garments indicating “Machine

Washable Silks” or “Gentle” cycle on the care label. Place small items in mesh garment bags before washing. This cycle features a spray rinse.

Low Use this cycle to wash lightly soiled garments indicating

“Machine Washable Silks” or “Gentle” cycle on the care label. Place small items in mesh garment bags before washing. This cycle features a spray rinse.

Low Similar to the way garments are hand-washed in a sink, this

cycle combines periods of low-speed agitation and soaking. This cycle features a spray rinse.

NOTE: Use mesh garment bags as needed.

an additional rinse cycle or to complete a load after power interruption. Also use for loads that require rinsing only.

fabrics or special-care items washed by hand. Use this cycle to drain washer after cancelling a cycle or completing a cycle after a power failure.

Cycle Details:

USING YOUR WASHER

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

re, or electrical shock.

1. Sort and prepare your laundry

■ Empty pockets. Loose change, buttons, or any small object

can pass under the agitator and become trapped, causing unexpected sounds.

■ Sort garments by recommended cycle, water temperature,

and colorfastness.

■ Separate heavily soiled garments from lightly soiled.

■ Separate delicate garments from sturdy fabrics.

■ Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

■ Treat stains promptly.

■ Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to garments

during washing.

Helpful Tips:

■ When washing water-proof or water-resistant items, load

evenly.

■ Use mesh garment bags to help avoid tangling when washing

delicate or small garments.

■ Turn knits inside out to avoid pilling. Separate lint-takers from

lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.

2. Add laundry products

Add a measured of amount of detergent or single-dose laundry packet into the basket.

If using Oxi-type boosters, color-safe bleach, or fabric softener crystals, add to the bottom of the washer basket before adding clothes.

NOTE: Follow the manufacturer’s instructions to determine the amount of laundry products to use.

3. Load laundry into washer

Load garments in loose heaps evenly around basket wall. For best results, do not pack the load tightly. Do not wrap large items such as sheets around the agitator; load them in loose piles around the sides of the basket. Try mixing different sized items to reduce tangling.

IMPORTANT: Do not tightly pack or force items into washer. Items need to move freely for best cleaning and to reduce wrinkling and tangling.

4. Add liquid chlorine bleach to

dispenser

5. Add fabric softener to dispenser

(on some models)

Pour a measured amount of liquid fabric softener into dispenser; always follow manufacturer’s directions for correct amount of fabric softener based on your load size.

IMPORTANT:

• Dilute liquid fabric softener by lling the

dispenser with warm water until liquid reaches the underside of the rim. See Max Fill line arrows. Then set Fabric Softener option knob to YES.

• Fabric Softener option knob must be set to

YES to ensure proper distribution at correct time in cycle.

Adding Liquid Fabric Softener Manually to Wash Load

During the nal rinse, wait until the washer has completed lling, press the START/Pause/Unlock Lid button to pause the washer. Lift the lid and add the measured recommended amount of liquid fabric softener. Do not use more than the recommended amount. Close the lid and press the START/Pause/Unlock Lid button again to start the washer.

MAX FILL

Liquid

Chlorine Bleach

Do not overll, dilute, or use more than 1 cup (250 mL). Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach.

6. Select CYCLE

Turn cycle knob to choose your wash cycle. For more information, see “Cycle Guide”.

7. Select LOAD SIZE

Select the Load Size setting most suitable for your load. Extra small or small will add a low amount of water for smaller loads and Large will add the most amount of water for large or bulky loads. Garments need to move freely.

9. Select options, if desired (on some

models)

If you are using fabric softener, be sure to set the Fabric Softener option knob to YES.

8. Select WASH TEMP/

TEMPERATURE

Once you select a cycle, select the desired temperature by turning the Wash Temp/Temperature knob to the appropriate setting based on your load. All rinses are cold.

NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.

Wash Temp/Temperature Suggested Fabrics Hot

Some cold water is added to save energy. This will be cooler than your hot water heater setting.

Warm

Some cold water will be added, so this will be cooler than what your previous washer provided.

Cool

Warm water may be added to assist in soil removal and to help dissolve detergents.

Cold

This is the temperature from your faucet. If your tap cold water is very cold, warm water may be added to assist in soil removal and help dissolve detergent.

Whites and pastels Durable garments Heavy soils

Bright colors Moderate to light soils

Colors that bleed or fade

Light soils

Dark colors that bleed or fade

Light soils

10. Press START/Pause/Unlock Lid

to begin wash cycle

Press the START/Pause/Unlock Lid button to start the wash cycle. When the cycle has nished, the CYCLE COMPLETE indicator will light. Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and rusting of metal hooks, zippers, and snaps.

Unlocking the lid to add garments

If you need to open the lid to add 1 or 2 missed garments: Press START/Pause/Unlock Lid; the lid will unlock once

the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Then close lid and press START/Pause/Unlock Lid again to restart the cycle.

If lid is left open for more than 10 minutes, the water will pump out automatically.

WASHER MAINTENANCE

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the “Installation Instructions” for more information.

WASHER CARE

WASHER CARE (cont.)

Recommendations to Help Keep Your Washer Clean and Performing at its Best

1. Always follow the detergent manufacturer’s instructions

regarding the amount of detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.

3. Always leave the washer lid open between uses to help dry

out the washer and prevent the buildup of odor-causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions provided above, and use this recommended monthly cleaning procedure:

Recommended Cycle for Cleaning the Washer

Refer to the “Cycle Guide” for the optimal cycle for cleaning the inside of the washer. Use this cycle with affresh® Washer Cleaner or liquid chlorine bleach as described below.

Begin procedure

1. affesh® Washer Cleaner Cycle Procedure (Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items. b. Place an affesh® Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh® Washer Cleaner tablet

in the detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid. f. Select the cycle recommended for cleaning the inside

of the washer.

g. Press the START/Pause/Unlock Lid button to start the

cycle.

NOTE: For best results, do not interrupt cycle. If cycle must be interrupted, press START/Pause/Unlock Lid once or twice (depending on model). After the cycle has stopped, run a RINSE/SPIN cycle to rinse cleaner from washer.

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing or items. b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time.

c. Close the washer lid. d. Do not add any detergent or other chemical

to the washer when following this procedure. e. Select the cycle recommended for cleaning the inside

of the washer.

f. Press the START/Pause/Unlock Lid button to start the

cycle.

Cleaning the Dispensers

After a period of using your washer, you may nd some residue buildup in the washer’s dispensers. To remove residue from the dispensers, wipe them with a damp cloth and towel dry. Do not attempt to remove the dispensers or trim for cleaning. The dispensers and trim are not removable. If your model has a dispenser drawer, however, remove the drawer and clean it before or after you run the Clean Washer cycle. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills. Use only mild soaps or cleaners when cleaning external washer surfaces.

IMPORTANT: To avoid damaging the washer’s nish, do not use abrasive products.

NON-USE AND VACATION CARE

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid ooding due to

water pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE/SPIN cycle for about 30 seconds to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain from drain system and drain any

remaining water into a pan or bucket. Disconnect drain hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy blankets or towels into basket opening. Close lid and place tape over lid and down front of washer. Keep lid taped until washer is placed in new location.

+ 22 hidden pages