Ingersoll-Rand 650518, 650517 User Manual
OPERATOR’S
MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
ALSO INCLUDE MANUALS: PH10AĆXĆX HIGH PRESSURE DIAPHRAGM PUMP (PN 97999Ć801), 6661MXĆXĆC DIAPHRAGM PUMP
(PN 97999Ć619), L262X1ĆXXX REGULATOR (PN 100400Ć7), P292X1ĆXXX PIGGYBACK FILTER / REGULATOR (PN 100400Ć8).
650517 & 650518
650517
650518
RELEASED: 4-10-97
REVISED: 9-15-00
(REV
. C)
DELIVERY
1”
DIAPHRAGM PUMP
SERVICE KITS
Use only genuine ARO replacement parts to assure compatible presĆ
sure rating and longest service life.
• Fluid Section Repair Kit 637179.
• Air Section Repair Kit 637178.
Refer to the 6661MXĆXĆC Operator's Manual for parts / repair and serĆ
vice information (model 650517).
Refer to the PH10AĆXĆX Operator's Manual for parts / repair and serĆ
vice information (model 650518).
PUMP
System Model 650517 (aluminum)..........
Basic Pump Model 6661M0Ć2A4ĆC (aluminum).....
Pump Type 3:1 Ratio, Metallic Air Operated Double...........
Material Aluminum..............
Air Inlet 3/8" Ć 18 N.P.T.F...............
Maximum Air Inlet Pressure 100 p.s.i.g. (6.9 bar)
Maximum Outlet Pressure 300 p.s.i.g. (20.4 bar)
Maximum Flow Rate 24 g.p.m. (90.7 l/m)....
Maximum Particle Size 1/8" (3.2 mm)..
Maximum Temp. Limits 35_ to 150_F(2_ to 66_C)..
Noise Levelh 84.5 db(A) @ 70 psi, 60 cycles per minute...........
SYSTEM DA
650518 (stainless steel)
PH10AĆASSĆSST (stainless steel)
Diaphragm with stainless steel seats
TA
, 3:1 RATIO, WITH WALL MOUNT
SYSTEM
OPERATING INSTRUCTIONS
WARNING
SURE OF 300 P.S.I. (20.4 BAR) AT 100 P.S.I. (6.9 BAR) AIR INĆ
LET PRESSURE.
WARNING READ THE PUMP MANUAL FOR ADDITIONAL
OPERATING AND SAFETY PRECAUTIONS AND OTHER IMĆ
PORTANT INFORMATION.
• Install the connector to the air supply hose.
• Attach (17) ground kit to ground lug.
• Attach the ground wire to a suitable ground.
• Keep containers covered to prevent contamination.
• When using an agitator, install a T" at the air inlet or use a sepĆ
arate air supply source.
1. Turn the knob on the air regulator counterclockwise to zero p.s.i.
2. Place (11) tube into the container of material.
3. Start the pump to cycle by turning the air regulator knob clockwise.
The pump will cycle several strokes until pressure is built up in the
system, at which time it will stop. Check for any loose fittings or
leakage.
DO NOT EXCEED MAXIMUM OPERATING PRESĆ
INITIAL
SETUP PROCEDURE
START-UP
h The pumpsound pressurelevels publishedhere havebeen updatedtoanEquivalentContinuousSoundLevel
(L
) to meet the intent of ANSI S1.13Ć1971, CAGIĆPNEUROP S5.1 using four microphone locations.
Aeq
GENERAL
The 650517 & 650718 Wall Mount Pumping System includes fittings,
wall bracket, regulator, siphon tube, gauge and hardware.
The diaphragm pump uses stainless steel balls and seats, and teflon
diaphragms and is designed to be used with waterborne paints. The
gun and low pressure air and material hoses are not included.
INGERSOLL-RAND COMPANY
P.O. BOX 151 D ONE ARO CENTER D BRYAN,OHIO 43506Ć0151
&
(419) 636-4242 D F
DESCRIPTION
AX (419) 633-1674
E2000 D PRINTED IN U.S.A.
PARTS LIST / 650517 / 650518
Item Description (Size in inches)
(Qty)
Part No.
2 Wall Mount Bracket Assembly (1) 67142
3 Bracket Assembly (1) 104171
4 Hose (1) 622702Ć6
5 Diaphragm Pump (model 650517) (1) 6661M0Ć2A4ĆC
(model 650518) (1)
PH10AĆASSĆSST
6 Lubricator Assembly (1) L26231Ć110
7 Modular PiggyBack (1) P29231Ć610
9 Male Elbow (2) 59756Ć260
l 10 Tubing (5/32" x 18" long) (1) 94979ĆXXXĆX
11 Tube (37Ć1/2" long) (1) 94415Ć2
12 Gauge (0 Ć 160 p.s.i.) (1) 100091
13 Machine Screw (1/4" Ć 20 x 5/8" long) (2) Y8Ć48ĆC
14 Jam Nut (1/4" Ć 20) (2) Y12Ć104ĆC
15 Lock Washer (1/4") (2) Y14Ć416
16 90_ Elbow (1" Ć 11Ć1/2 NPTF) (1) Y43Ć16ĆS
9
4
9
11
6
l Bulk Tubing (100' long).
5
16
10
3
12
2
13
14
15
PAGE2OF2 650517
7
PN 97999Ć677
Loading...