Ingersoll-Rand 106 Operation And Maintenance Manual

03537016

Form P6878
Edition 4
February, 1994

OPERATION AND MAINTENANCE MANUAL

for

106 MODEL B SUPER DUTY RATCHET WRENCH

TPB1714

IMPORTANT SAFETY INFORMATION ENCLOSED.

READ THIS MANUAL BEFORE OPERATING TOOL.

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

• Always operate, inspect and maintain this tool in

accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).

• For safety, top performance and maximum dura-

bility of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8” (10 mm) inside diameter air supply
hose.

• Air powered tools can vibrate in use. Vibration,

repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain oc­curs. Seek medical advice before resuming use.

• Always turn off the air supply and disconnect the

air supply hose before installing, removing or

The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool perfor­mance and increased maintenance, and may invalidate all warranties.

Ingersoll–Rand is not responsible for customer modification of tools for applications on which Ingersoll–Rand was not
consulted.

Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized Servi­center.

It is the responsibility of the employer to place the information in this manual into the hands of the operator.

adjusting any accessory on this tool, or before per­forming any maintenance on this tool.

• Keep hands, loose clothing and long hair away

from rotating end of tool.

• Anticipate and be alert for sudden changes in mo-

tion during start up and operation of any power
tool.

• Tool accessory may continue to rotate briefly after

throttle is released.

• Do not lubricate tools with flammable or volatile

liquids such as kerosene, diesel or jet fuel.

• Do not remove any labels. Replace any damaged

label.

• Use accessories recommended by Ingersoll–Rand.

• Use only impact sockets and accessories. Do not

use hand (chrome) sockets or accessories.

Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.

 Ingersoll–Rand Company 1994

Printed in U.S.A.

WARNING LABEL IDENTIFICATION

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

2

2

PLACING TOOL IN SERVICE

LUBRICATION

Ingersoll–Rand No. 10 Ingersoll–Rand No. 28

Always use an air line lubricator with this tool.
We recommend the following Filter–Lubricator–Regulator
Unit:

For USA – No. C22–04–G00
For International – No. C26–C4–A29

Before starting the tool and after each two or three
hours of operation, unless the air line lubricator is used,

pour approximately 1.5 cc of Ingersoll–Rand No. 10 Oil
into the air inlet.
After each 40 hours of operation, or as experience indi­cates, inject about 0.5 cc of Ingersoll–Rand No. 28 Grease
into the Grease Fitting (32).
Whenever the Ratchet Head is removed from the power
unit, work some Ingersoll–Rand No. 28 Grease into the
Front Rotor Bearing (20) and Spindle Bearing (28). Coat
the Planet Gears (27) with a light film of Ingersoll–Rand
No. 28 Grease.

INSTALLATION

Air Supply and Connections

Always use clean, dry air . Dust–corrosive fumes and/or
excessive moisture can ruin the motor of an air tool. An
air line filter can greatly increase the life of an air tool.
The filter removes dust and moisture.

Low pressure (under 90 psig; 6.2 bar/620 kPa) reduces the
speed of air tools. Low pressure not only wastes time, but
also costs money. High pressure (over 90 psig; 6.2
bar/620 kPa) raises performance beyond the rated capacity
of the tool and could cause injury.
Make sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905–1 for a typical
piping arrangement.

MAIN LINES 3 TIMES
AIR TOOL INLET SIZE

TO
AIR
SYSTEM

TO
AIR
TOOL

LUBRICATOR

REGULATOR

BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE

DRAIN REGULARLY

FILTER

COMPRESSOR

(Dwg. TPD905–1)

The 106 Model A Ratchet Wrench is designed for muffler and shock absorber work, replacement of water
pumps, radiators and air conditioning units and general automotive repair.

HOW TO ORDER A RATCHET WRENCH

3/8” HEAVY DUTY RATCHET WRENCH

Recommended Torque Range

Model Free Speed, rpm in. mm

106 Model B 210 10 to 50 13 to 36

3

3

MAINTENANCE SECTION

4

(Dwg. TPB839)