Infratech WD 6024 SS, WD 5024 SS, WD 4024 SS, W4024 SS, W1512 SS User Manual

U

L

US

C

LISTED

ALL WEATHER W-SERIES QUARTZ TUBE
ELECTRIC INFRARED RADIANT HEATER

INSTALLATION USE & CARE MANUAL

TABLE OF CONTENTS:

IMPORTANT INFORMATION

Assembly Instructions ……………………………………………………………………
Wiring Instructions ……………………………………………………………………
Outdoor Installation ……………………………………………………………………
Electrical Warning ……………………………………………………………………

APPLICATION INFORMATION

Mounting Instructions …………………………………………………………………
Typical Wiring (Schematics) ……………………………………………………………………
General Notes ……………………………………………………………………
Areas Covered (Table) ……………………………………………………………………
Location Suggestions ……………………………………………………………………

PARTS LIST

Parts List ……………………………………………………………………
Trouble Shooting Guide ……………………………………………………………………
Warranty ……………………………………………………………………
Warranty Registration ……………………………………………………………………

3&4

2
2
2
2

4
5
5
6

7
7
8
8

SAVE THIS MANUAL FOR FUTURE REFERENCE

MADE IN U.S.A.

1

ASSEMBLY INSTRUCTIONS – ELECTRIC HEATER

This heater must be permanently installed and hard wired by a licensed electrician. Assembly
procedure must be performed with no electrical power to unit.

NOTE: To prevent breakage, unit is shipped without the element installed.

1. Check UL/CE label on Heater for proper voltage

2. Remove two end reectors.

3. Open element clips at each end of the Heater and carefully install the quartz tube.
Remove one nut from end of element. Slip on wire over element screw. Replace nut.
NOTE: Hold element ceramic rmly while tightening nut to prevent damage to element.
Nut should be tightened snug, a loose connection can cause element to short or fail.
Connect other side of element in like manner. Close element clips over tube.

4. Replace end reectors.

5. If necessary, clean tube and reector with alcohol or equivalent.

6. Snap on protective grill provided.

WIRING INSTRUCTIONS

1. Remove cover plate from junction box.

2 Attach conduit.

3. Use only copper or aluminum wire
suitable for 90°C.

4. Replace cover plate.

5. Observe local electrical code
regulations.

WARNING

Unit may be a source of possible shock.

Unit may be a source of possible ignition, maintain required clearances to all combustibles.

Never block the front panel of the Heater.

Do NOT operate within 25 feet of ammable/explosive material.

NEVER attempt to service Heater without disconnecting it’s power source.

OUTDOOR INSTALLATION

1. Heater must be mounted with reector
angled down.

2. All electrical connections must be in
compliance with the National Electric
Code and local codes for outdoor
wiring.

3. Use only wiring components UL/CE
listed for outdoor use with IP X 4
minimum rating

This appliance is not intended for use by young children or inrm persons unless they
have been adequately supervised by a responsible person to ensure that they can use the
appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
Do not use if the heating element is damaged.
The heater must be installed at least 7’ (2.1 mm) above the oor.
A means for disconnection of the appliance must be incorporated in accordance with the
local wiring codes.

2

INSTALLATION INSTRUCTIONS – ELECTRIC HEATER

The following information is designed to help you apply and install INFRATECH QUARTZ TUBE
ELECTRIC HEATERS in a variety of locations. INFRATECH heaters are one of the most economi­cal of all radiant heaters to buy, and can be some of the least costly to operate. They may also
be the most economical to install, depending on the location of electrical power adequate to
operate the heater(s) properly.

MOUNTING INSTRUCTIONS

These models may be chain or bracket mounted to any ceiling or horizontal surface. Installa­tion must be such that 18” minimum clearance is maintained around the heater in front of the
plane of the face. 6” of clearance provided by Mounting Brackets is required behind the plane
of the face.

Wall/ ceiling brackets are furnished with all heaters. Their use is optional. When used, they
allow heater to be fastened to wall or ceiling and then tipped up to 60°.

Heater can also be hung in a horizontal position us­ing chains or custom brackets. Heater must be level,
but can be rotated around its horizontal axle.

3