Infratech ALL WEATHER QUARTZ TUBE ELECTRIC HEATER Installation Use & Care Instructions

ALL WEATHER QUARTZ TUBE

Innovative Infrared Technology

ELECTRIC HEATER

INSTALLATION USE & CARE MANUAL

TABLE OF CONTENTS:

IMPORTANT INFORMATION

Assembly Instructions ……………………………………………………………………
Wiring Instructions ……………………………………………………………………
Outdoor Installation ……………………………………………………………………
Electrical WARNING ……………………………………………………………………

APPLICATION INFORMATION

Application Information ……………………………………………………………………
Typical Wiring (Schematics) ……………………………………………………………………
General Notes ……………………………………………………………………
Areas Covered (Table) ……………………………………………………………………
Location Suggestions ……………………………………………………………………

PARTS LIST

Parts List ……………………………………………………………………
TROUBLESHOOTING GUIDE ……………………………………………………………………
WARRANTY ……………………………………………………………………
WARRANTY REGISTRATION ……………………………………………………………………

SAVE THIS MANUAL FOR FUTURE REFERENCE

3
3
4
5

4
5
6
6
7

8
8
9
A

ASSEMBLY INSTRUCTIONS – ELECTRIC HEATER

NOTE: To prevent breakage, unit is shipped without the element installed.

1. Check UL/CE label on Heater for proper voltage

2. Remove end plates.

3. Open element clips at each end of the Heater and carefully install the quartz tube. Re
move one nut from end of element. Slip on wire over element screw. Replace nut.
NOTE: Hold element ceramic rmly while tightening nut to prevent damage to element.
Nut should be tightened snug, a loose connection can cause element to fail.
Connect other side of element in like manner. Close element clips over tube.

4. Replace end plates.

5. Clean tube and reector with alcohol or equivalent.

6. Snap on protective grill provided.

WIRING INSTRUCTIONS

1. Remove cover plate from junction box.

2 Attach conduit.

3. Use copper or aluminum wire suitable
for 90°C.

4. Replace cover plate.

5. Observe local electrical code
regulations.

WARNING

Unit may be a source of possible shock

Unit may be a source of possible ignition, maintain required clearances to all combustibles

Never block the front panel of the Heater

Do NOT operate within 25 feet of ammable/explosive material
NEVER attempt to service Heater without disconnecting its power source

OUTDOOR INSTALLATION

1. Heater must be mounted with reector
angled down.

2. All electrical connections must be in
compliance with the National Electric
Code and local codes for outdoor
wiring.

3. Use only wiring components UL/CE
listed for outdoor use with IP X4
minimum rating

This appliance is not intended for use by young children or inrm persons unless they
have been adequately supervised by a responsible person to ensure that they can use the
appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
Do not use if the heating element is damaged.
The heater must be installed at least 7’ (2.1 mm) above the oor.
A means for disconnection of the appliance must be incorporated in accordance with the
local wiring codes.

INSTALLATION INSTRUCTIONS – ELECTRIC HEATER

The following information is designed to help you apply and install INFRATECH QUARTZ TUBE
ELECTRIC HEATERS in a variety of locations. INFRATECH heaters are one of the most economi­cal of all radiant heaters to buy, and can be some of the least costly to operate. They may also
be the most economical to install, depending on the location of electrical power adequate to
operate the heater(s) properly.

MOUNTING INSTRUCTIONS

These models may be chain or bracket mounted to any ceiling or horizontal surface. Installa­tion must be such that 18” minimum clearance is maintained around the heater in front of the
plane of the face. 6” of clearance is required behind the plane of the face.

Wall/ ceiling brackets are furnished with all heaters. Their use is optional. When used, they
allow heater to be fastened to wall or ceiling and then tipped up to 60o.

Heater can also be
hung in a horizontal
position using chains or
custom brackets. Heat­er must be level, but
can be rotated around
its horizontal axel.