InFocus Work Big IN2102, Work Big IN2104, Work Big IN2106, in2102, in2104 Quick Start Manual

in2102 in2104 in2106

Quick Start Guide

Regulatory models W2100 and W2106

2 31

Status Indicator Panel

1

2

+

-

+

Unpack the box

Here's what's included:

Put batteries in the remote

The remote uses 2 AA batteries.

Projector

Computer Cable

Save the box and packing materials.

Please dispose of batteries in an environmentally proper manner.

Remote

Power Cable

The top of your projector includes a
convenient indicator panel with symbols that
light up to show important status.

For details, see Troubleshooting.

Power/Standby

Service Required

High Temperature Replace Lamp

Please read the safety instructions booklet before setting up
the projector.

USB Cable

Buy a Full-Featured Remote and Other Custom Accessories

www.infocus.com/store

OR

3

Mini-Plug Audio Y-Cable









Connect source

Color-coded connections make it easy.
You can connect more than one source if needed.

Connect to: Computer

Connect to: DVD or VCR* (using optional cables)

Computer Cable (included)

Computer

*Also for game console or cable box.

Connect video using either an S-Video or a Composite Video cable

Connect audio using a Mini-Plug to RCA Audio Y-Cable

1

2

Composite Video Cable

Video Cable

Good

Better

Want better sound?

Connect the source's audio output to a
receiver/amplifier or home theater
system with separate speakers.

S-

DVD or VCR

Audio Out

L R

Video Out

USB connection only needed for:
Presentation control using
projector remote
Upgrading projector firmware

To Projector

RCA Audio Cable

DVD or VCR

Home Theater or Receiver

Audio In

L R

Audio Out

Video Out

L R

or

Got an Apple computer?

You may need an adapter. For more
information, see How-To Guides at

www.infocus.com/support/howto

OR

Connect to: Other kinds of sources

How-To Guides are available at www.infocus.com/support/howto

USB is optional

OR

USB Cable (included)

www.infocus.com/store part no. SP-SVIDEO-10M or SP-CPSTVID-5M

Available from A/V dealer or retailer

4

T

1 Connect the power cord to the projector

and to an electrical outlet

3 Turn on the projector

4 Wait for the lamp to warm up

5 Turn on computer or other source

6 Change source if needed

The power light on the projector will light amber.

Press power (on the projector or remote).
The power light will start blinking green.

After a few seconds, the power light will stop blinking and turn
green. It can take a minute for the lamp to reach full brightness.

If needed, press source (on the projector or remote) to view the
source. You may have to press it more than once.

You may need to press a specific key combination to activate
your laptop's external video port. On most laptops, hold down
the FN key while pressing a key labeled CRT/LCD, LCD/VGA,
a monitor icon , or similar. Key combos for popular models:

Warning: Do not look directly into the lens
when the projector is turned on.

Important: If there is still no video, restart your
computer (first make sure it's connected to the
projector and the projector is turned on).

5-10 sec.

Apple F7
Dell Fn+F8
Fujitsu Fn+F10

IBM ThinkPad Fn+F7
Toshiba Fn+F5

Gateway Fn+F3 or Fn+F4
HP/Compaq Fn+F4 or Fn+F6
Sony Fn+F7

source

Turn on projector and source

i

i

After a few seconds, the power light will stop blinking and turn
green. It can take a minute for the lamp to reach full brightness.

2 Remove the lens cap

Complete laptop activation chart at www.infocus.com/support

5

1 Height

2 Keystone

3 Zoom and focus

1 Hold down the release button

under the front of the projector.

2 Lift the front of the projector to

the desired height.

3 Release the button.

Press the keystone buttons to
make the picture square.

Adjust zoom first, then focus the
center of the image.

To flip the image, turn on the Ceiling

Mount setting in the Setup menu.

Ceiling mount?

Adjust the picture

Projector Location

As distance increases, the
image gets larger and
moves upwards.

Diagonal
Screen Size

Distance to Screen

Minimum Maximum

60" / 1.5m

80" / 2m

92" / 2.3m

150" / 3.8m

7'6" / 2.3m

10'2" / 3.1m

11'10" / 3.6m

19'4" / 5.9m

8'6" / 2.6m

11'6" / 3.5m

13'1" / 4.0m

21'8" / 6.6m

Lens center line

Zoom
(rear)

focus
(front)

1

2

Interactive Screen Size and

Distance Calculator

www.infocus.com/calculator

Buy a Screen and Other Custom

Accessories

www.infocus.com/store

6

7

8

Press the power button

1 Press menu, then press or to review menus.
2 Press select to enter a menu, then press or to review settings.
3 Press select to change a setting. If this shows more choices, press

or to update the setting, then press select or menu to save it.

4 Press menu to go back. Press it again to remove the menu.

Using the menus

Turn off the projector

Register your product

Optional: Read the Reference Guide

Activate your warranty to ensure eligibility for service and support.
Get special offers and notifications about free product updates.

The power light on the projector will blink while the fan cools
the lamp. If you need to unplug the projector, wait until the
fan stops and the power light stops blinking and stays on.

Note: While the power light is blinking, button presses on the
projector and remote are ignored.

Controlling your presentations

Connect the USB cable between the projector and your computer (see step ),
then press and to move through your presentation slides.

1 Write down your projector's serial number

It's printed on the label on the back of the projector. You'll need it to register (and if
you ever need to contact support).

Serial number:

The Reference Guide is available in multiple languages. It covers advanced setup and
operation, including lamp replacement instructions.

3

Note: Most picture settings are disabled (gray) unless a source is being displayed.

Download it at www.infocus.com/support

2 Go to www.infocus.com/register

4

Troubleshooting

If there is no picture or the picture is blank

If the power light is off, make sure the power cord is connected and plugged

into a live electrical outlet. If the power light is amber and not blinking, press
the power button.

Check video source and cables. Make sure the video source (computer, DVD

player, VCR, etc.) is turned on and cables are securely connected between the
source and the projector.

Make sure your computer's video port is enabled. Press the key combination

that activates your laptop's external video port (see step ). If there is still no
image, restart your laptop.

Press the Source button. You may need to press it several times to view the

correct source.

Press the Auto Image button.

If "Signal out of range" is shown, or the picture looks bad

Press the Auto Image button. If that doesn't help (and the source is a computer),

reduce your computer's display resolution or vertical refresh rate.

If the replace lamp light is on

Turn the projector off and wait at least one minute, then turn it on again. If the

replace lamp light turns on again, the lamp needs to be replaced. For lamp
replacement instructions, see the Reference Guide, which can be downloaded at

Only InFocus genuine lamps are tested for use in this projector.

If the high temperature light is on

Turn the projector off and remove anything that may be blocking the air vents

on its side. Leave the projector off for at least one minute to let it cool before

turning it on again. Important: Continuous operation at high temperature may
reduce the lifetime of the lamp and/or projector.

If the service required light is on

Turn the projector off and wait at least one minute, then turn it on again. If the

service required light turns on again, the projector needs to be serviced. See
below for service contact information.

More troubleshooting options are in the Reference Guide

Warning: In the unlikely event of a lamp rupture, particles may be ejected from the projector.

Keep out of the area under and around the projector when it is turned on. See the safety
instructions booklet for more details.

source

Download it at www.infocus.com/support

www.infocus.com/support

We’re here to support you with your new purchase. We can help you with…

• Determining screen sizes

• Documentation in other languages

• Connecting your sources (TV, DVD, Cable/Satellite, Game, etc.)

• Selecting optional accessories

• Product warranty protection plans

Hg - Lamp contains mercury. Manage in accordance with local disposal laws.
See www.lamprecycle.org

Declaration of Conformity

Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070-8238 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conforms to the following directives and norms: EMC Directive
2004/108/EC, EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3, Low Voltage Directive 2006/95/EC, Safety: IEC 60950-1:1st
Edition.

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered
trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of
Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP
logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and
INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

FCC Warning

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment that are not expressly approved by InFocus Corp. may void the user’s authority to operate
the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, cUL
Other specific Country Approvals may apply. Please see product certification label.

Input ratings: 100-240Vac, 3.0A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

USA, Canada, Latin America

Customer Support Telephone

[phone]

TOLL FREE: 800-799-9911
Mon-Fri, 7 am - 5 pm Pacific
[e-mail]

Asia Pacific

Customer Support Telephone
Singapore: [phone]
China: 800.828.2268
Australia: 1300-725-295
Australia Direct Sales: 1800-885-841
Mon-Fri, 9 am - 5 pm SGT
[e-mail]

Europe, Middle East, Africa

Customer Support Telephone

[phone]

Mon-Fri, 08:30 - 18:00 CET
[e-mail]

Questions? We’re here to help!

Visit us at:

www.infocus.com/support