reference series
311a,611a,
1211a,7521a,
7541a,5761a
instructions
Thank you
In order that we may better serve you should you require warranty
service for your new amplifier, please retain your original purchase
receipt and read the enclosed warranty information card.
for purchasing a Reference Series amplifier.
INTRODUCTION
HIGH-LEVEL
INPUT
Speaker Wires
(spliced)
RL
+
R
–
+
L
–
+ WHITE
– WHITE/BLACK
GRAY/BLACK –
GRAY +
CHOOSING A LOCATION AND
MOUNTING THE AMPLIFIER
POWER CONNECTIONS
WARNING!
Playing loud music in an automobile can hinder
your ability to hear traffic and permanently
damage your hearing. We recommend listening
at low or moderate levels while driving your
car. Infinity accepts no liability for hearing loss,
bodily injury or property damage resulting from
the use or misuse of this product.
IMPORTANT
To get the best performance from your Reference
Series amplifiers, we strongly recommend
that installation be entrusted to a qualified
professional. Although these instructions explain
how to install Reference amplifiers in a general
sense, they do not show specific installation
methods that may be required for your particular
vehicle. If you do not have the necessary tools or
experience, do not attempt the installation yourself. Instead, please ask your authorized Infinity
car audio dealer about professional installation.
INSTALLATION WARNINGS AND TIPS
•
Always wear protective eyewear when using
tools.
•
Turn off the audio system and other electrical
devices before you start. Disconnect the (–)
negative lead from your vehicle’s battery.
•
Check clearances on both sides of a planned
mounting surface before drilling any holes or
installing any screws. Remember that the
screws can extend behind the surface.
•
At the installation sites, locate and make a note
of all fuel lines, hydraulic brake lines, vacuum
lines and electrical wiring. Use extreme caution
when cutting or drilling in and around these
areas.
Choose a mounting location in the trunk or
cargo area where the amplifier will not be damaged by shifting cargo. Amplifier cooling is
essential for proper amplifier operation. If the
amplifier is to be installed in an enclosed space,
make sure there is sufficient air circulation for
the amplifier to cool itself.
When mounting the amplifier under a seat,
ensure that it is clear of all moving seat parts
and does not affect the seat adjustments. Mount
the amplifier so it is not damaged by the feet
of backseat passengers. Make sure that the
amplifier is mounted securely using nuts and
bolts or the supplied mounting screws.
Mount the amplifier so that it remains
dry – never mount an amplifier outside
the vehicle or in the engine compartment.
The Reference amplifiers are capable of
delivering high power levels, and require a
reliable connection to the vehicle’s electrical
system in order to perform optimally. See
Figure 1 for connection location. Please
adhere to the following instructions carefully.
GROUND CONNECTION
Connect the amplifier’s Ground (GND) terminal
to a solid point on the vehicle’s metal chassis,
as close to the amplifier as possible. Refer to the
chart below to determine minimum wire-gauge
size. Sand away any paint from this location; use
a star-type-lock washer to secure the connection.
POWER CONNECTION
Connect a wire (see chart at right for appropriate
gauge) directly to the vehicle’s positive battery
terminal, and install an appropriate fuse holder
within 18" of the battery terminal. Do not
install the fuse at this time. Route the wire to
the amplifier’s location, and connect it to the
amplifier’s positive (+12V) terminal. Be sure to
use appropriate grommets whenever routing
wires through the firewall or other sheet metal.
Failure to adequately protect the positive wire
from potential damage may result in a vehicle
fire. When you are done routing and connecting
this wire to the battery and to the amplifier,
you may install the fuse at the battery. The
fuse value should be selected based on total
amplifier-current draw; see chart at right.
REMOTE CONNECTION
Connect the amplifier’s Remote (REMOTE)
terminal to the source unit’s Remote Turn-On
lead using a minimum of 18-gauge wire. If your
source unit does not have a remote turn-on
connection, connect the amplifier’s (REMOTE)
terminal to the vehicle’s accessory circuit.
WIRE-GAUGE CHART
Amplifier Maximum Minimum
Model Current Draw Wire Gauge
7521a 34A #8 AWG
7541a 85A #8 AWG
5761a 87A #8 AWG
311a 40A #8 AWG
611a 69A #6 AWG
1211a 115A #4 AWG
These recommendations assume 7' – 10' wire
runs. If your installation differs markedly, you
will need to adjust the wire gauge accordingly.
SPEAKER CONNECTIONS
Refer to the application guides on the pages
that follow. Speaker connections should be
made using a minimum of 16-gauge wire.
HIGH-LEVEL INPUT CONNECTIONS
The 7521a, 7541a and 5761a amplifiers are
equipped with speaker-level inputs that allow
you to add an amplifier to head units that do
not have RCA line outputs. The speaker outputs
for the source unit should be connected to the
amplifier using the supplied connector (square
four-wire plug). Remember to check for proper
polarity. The 311a, 611a and 1211a amplifiers
are not equipped with high-level inputs.
NOTE: When using the low-level or high-level
inputs, the AUX outputs can be used to pass a
full-range line-level signal to another amplifier.
Figure 2. Speaker-level connector.
•
Before drilling or cutting holes, use a utility
knife to remove unwanted fabric or vinyl to
keep material from snagging in the drill bit.
•
When routing cables, k
ay from power cables and speak
aw
•
When making connections, mak
eep input-signal cables
are secure and properly insulated.
•
If the amplifier
only the same type and rating as that of the
original. Do not substitute another kind.
2
’s fuse must be replaced, use
Figure 1.Terminal-connection end plate.
er wires.
e certain they
APPLICATIONS – 311a, 611a AND 1211a
The Reference subwoofer amplifiers are
single-channel amplifiers. There are two sets of
terminals to make it easy to connect multiple
woofers. Either set of (+/–) terminals may be
used when connecting woofers.
To the right are two application diagrams to help
plan your subwoofer system installation. Figures
3 and 4 show how to configure the Reference
subwoofer amplifiers (models 311a, 611a and
1211a).
NOTE: For simplicity, Figures 3 and 4 do not
show power, remote and input connections.
NOTE: Minimum speaker load is 2 ohms.
APPLICATIONS – 7521a
The 7521a amplifier can be set up for stereo or
bridged-mono operation, as shown in Figures 5
and 6.
NOTE: For simplicity, Figures 5 and 6 do not show
power, remote and input connections.
NOTE: Minimum speaker impedance for
stereo operation is 2 ohms. Minimum speaker
impedance for bridged operation is 4 ohms.
Figure 3. Reference subwoofer amplifier with two woofer connections.
Figure 5. 7521a amplifier set up for stereo operation.
Figure 4. Reference subwoofer amplifier with one woofer connection.
Figure 6. 7521a amplifier set up for bridged-mono operation.
3
APPLICATIONS – 7541a
The 7541a can be set up for stereo 4-channel,
3-channel or bridged 2-channel operation, as
shown in Figures 7 through 9.
NOTE: For simplicity, Figures 7 through 9 do not
show power, remote and input connections.
NOTE: Minimum speaker impedance for
stereo operation is 2 ohms. Minimum speaker
impedance for bridged operation is 4 ohms.
NOTE: “Bass Boost” only affects rear channels.
Figure 7. 7541a amplifier in 4-channel (stereo) operation to drive front and rear full-range speakers.
Figure 8. 7541a is set up for 3-channel operation to drive a set of full-range speakers and a subwoofer.
4
Figur
e 9.
7541a used in bridged 2-c
hannel mode to dri
ve a set of components or subwoofer
s.
APPLICATIONS – 5761a
The 5761a can be configured for 6-channel,
5-channel or 3-channel operation, as shown
in Figures 10 through 12.
INPUT MODE SWITCH:
• Use INT (internal mode) to send a signal from
the front and rear inputs to the subwoofer.
• Use EXT (external mode) when sending a
dedicated signal to the subwoofer inputs; e.g.,
if your source unit has a subwoofer output.
NOTE: For simplicity, Figures 10 through 12 do
not show power, remote and input connections.
NOTE: Minimum speaker impedance for
stereo operation is 2 ohms. Minimum speaker
impedance for bridged operation is 4 ohms.
Figure 10. 6-Channel operation: 5761a amplifier driving full-range front and rear speakers and a pair of subwoofers.
Figure 11. 5-Channel operation: The same as Figure 10, with the subwoofer output bridged to drive a single 4-ohm subwoofer, providing
the speaker with more power.
Figure 12. 3-Channel operation: 5761a amplifier configured for 3-channel operation, where all of the channels are bridged for a
subwoofer and a pair of component speak
s.
er
5
INSTALLATION AND SETUP
SETTING THE CROSSOVER(S)
Determine your system plans and set the
crossover-mode switch accordingly. If your
system design does not include a subwoofer,
set the crossover mode to FLAT and skip to
“Setting Input Sensitivity.”
MODE SWITCH
Flat: Allows a full-range signal through to the
speakers; can be used with larger full-range
speakers such as 6" x 9"s.
HP: Allows a high-pass signal through to
the speakers; should be used with most
loudspeakers (can protect your full-range
speakers from being overdriven with low
frequencies, one cause of speaker damage).
LP: Allows bass to pass through to the speakers;
should be selected when powering subwoofers.
Figure 13. Control end panel.
Initially set the crossover-frequency control
midway. While listening to music, adjust the
crossover for the least perceived distortion from
the speakers, allowing them to reproduce as
much bass as possible.
Systems using a separate subwoofer set the
crossover mode to HP (high-pass) for your
full-range speakers. Adjust the crossover
frequency to limit bass, and provide increased
system volume with less distortion.
For subwoofers, choose the highest frequency
that removes vocal information from the sound
of the subwoofer.
If using the 7521a or 7541a to drive a subwoofer(s),
set the crossover mode to LP (low-pass).
NOTE: The 311a, 611a, 1211a and the subwoofer
output of the 5761a are low-pass only and do not
have a crossover-mode switch.
SETTING INPUT SENSITIVITY
1. Initially turn the INPUT LEVEL control(s) to
minimum (counterclockwise).
2. Reconnect the (–) negative lead to the vehi-
cle’s battery. Apply power to the audio system
and play a dynamic music track.
3. On the source unit, increase the volume
control to 3/4 volume. Slowly increase the
INPUT LEVEL control(s) toward three o’clock
until you hear slight distortion in the music.
Then reduce the INPUT LEVEL slightly until
distortion is no longer heard.
NOTE: After the source unit is on, blue LEDs (on
the top panel) will light, indicating the amplifier
is on. If not, check the wiring, especially the
remote connection from the source unit. Also
refer to “Troubleshooting” on page 7.
REMOTE LEVEL CONTROL (OPTIONAL)
All three Reference subwoofer amplifiers and
the 5761a amplifier have inputs for an optional
remote level control (100rc). This will allow the
subwoofer level to be adjusted from the listening
position. Connect the optional remote level
control using the RJ-11 jack on the side of the
amplifier. Install the control module in the front
of the vehicle within easy reach of the driver.
Both the underside of the dash and the center
console are suitable locations. Refer to the
mounting instructions accompanying the 100rc.
SETTING THE BASS BOOST
The 7521a, 7541a and 5761a are all equipped
with a bass-boost control. This allows you to
enhance the bass output of your system at
50Hz up to 12dB.
NOTE: Only rear channels of the 7541a are
affected by the bass boost control.
AUX OUTPUT
Reference amplifiers (except 5761a) are equipped
with full-range outputs that can be used to
connect additional amplifiers.
NOTE: When using the low- or high-level inputs,
the AUX outputs can be used to pass a full-range
line-level signal to another amplifier.
311a/611a/1211a
7541a
7521a
5761a
6
INSTALLATION AND SETUP (CONT.)
-9
-6
-3
0
-12
20 80
Freq. (Hz)
dB
DBO HP FREQ Control
(adjusts cut-off
frequency)
-6
0
6
12
-12
20 80
Freq. (Hz)
dB
DBO BOOST Control
(adjusts boost amount
at cut-off frequency)
HP FREQ
100Hz20Hz
BOOST
MAX MIN
-6
0
6
12
-12
20 80
Freq. (Hz)
dB
DBO BOOST Control
(adjusts boost amount
at cut-off frequency)
BOOST
MAX MIN
TROUBLESHOOTING
SETTING DBO™(311a, 611a and 1211a)
The Dynamic Bass Optimizer (DBO) is used to
enhance low-frequency reproduction in a vehicle.
Conventional bass-boost circuits only increase
bass at a fixed frequency, and cause the amplifier
to consume considerable power. The DBO allows
you to adjust the frequency (20Hz – 80Hz) as well
as the boost level (up to 12dB; see Figure 14),
allowing you to fine-tune the bass in your system
to optimize performance.
For sealed enclosures, the DBO can be used
to enhance the lower bass region of sealed
enclosures.
For bigger/fuller bass, adjust the HP FREQ
between 35Hz and 45Hz; adjust the BOOST
control according to your preference.
For tighter-sounding bass, adjust the HP FREQ
between 45Hz and 55Hz; adjust the BOOST
control according to your preference.
For vented enclosures, the DBO should be used
as a subsonic filter to reduce overexcursion
of the woofers. Set the HP FREQ control 10Hz
below the tuning frequency of the enclosure
(e.g., 25Hz for a box tuning of 35Hz); adjust the
BOOST control to taste. This will conserve
amplifier power typically wasted on frequencies
below the tuned frequency of the enclosure.
For infinite-baffle applications, set the HP FREQ to
the speaker’s Fs value (reducing overexcursion of
the woofer); adjust the Boost control to taste.
Figure 14. Frequency-response curves show
typical DBO control ranges.
STATUS LEDs
Clip: Indicates the amplifier is being overdriven,
and your speakers may be in danger. This
should blink only on musical peaks, and not
be on constantly.
Power: Indicates the amplifier is on.
Protection: Refer to “Troubleshooting” for specific
indications.
Figure 15. LED status.
•
PROBLEM:
No audio (POWER LED is off).
CAUSE and SOLUTION:
No voltage at BATT+ and/or REM terminals, or
bad or no ground connection. Check voltages
at amplifier terminals with VOM.
•
PROBLEM:
No audio (PROTECT LED flashes every
4 seconds).
CAUSE and SOLUTION:
DC voltage on amplifier output. Amplifier may
need service; see enclosed warranty card for
service information.
•
PROBLEM:
No audio (PROTECT LED is on).
CAUSE and SOLUTION:
Amplifier is overheated. Make sure amplifier
cooling is not blocked at mounting location;
verify that speaker-system impedance is within
specified limits.
•
PROBLEM:
No audio (PROTECT and POWER LEDs flash).
CAUSE and SOLUTION:
Voltage less than 9V on BATT+ connection.
Check vehicle charging system.
•
PROBLEM:
No audio (PROTECT LED is on).
CAUSE and SOLUTION:
Voltage greater than 16V or less than 8.5V on
BATT+ connection. Check vehicle charging
system.
•
PROBLEM:
Distorted audio.
CAUSE and SOLUTION:
Input sensitivity is not set properly, or amplifier
or source unit is defective. Check INPUT LEVEL
setting, or check speaker wires for shorts or
grounds.
•
PROBLEM:
Distorted audio (PROTECT LED flashes).
CAUSE and SOLUTION:
Short circuit in speaker or wire. Remove
speaker leads one at a time to locate shorted
speaker or wire, then repair.
•
PROBLEM:
Music lacks “punch.”
CAUSE and SOLUTION:
Speakers are not connected properly. Check
speaker connections for proper polarity.
7
SPECIFICATIONS
311a
• 116W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 81dBA (reference 1W into 4 ohms)
• 312W RMS x 1 channel at 2 ohms, 14.4V supply and
≤1% THD + N
• Dynamic power: 347W at 2 ohms
• Effective damping factor: 6.398 at 4 ohms
• Frequency response: 17Hz – 302Hz (–3dB)
• Maximum input signal: 6V
• Maximum sensitivity: 75mV
• Output regulation: .05dB at 4 ohms
• Dimensions (L x W x H): 12" x 11-7/16" x 2-11/16"
• Fuse rating: 1 x 30A
611a
• 456W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 70dBA (reference 1W into 4 ohms)
• 657W RMS x 1 channel at 2 ohms, 14.4V supply and
≤1% THD + N
• Dynamic power: 761W at 2 ohms
• Effective damping factor: 6.336 at 4 ohms
• Frequency response: 17Hz – 302Hz (–3dB)
• Maximum input signal: 6V
• Maximum sensitivity: 75mV
• Output regulation: .179dB at 4 ohms
• Dimensions (L x W x H): 12" x 15" x 2-11/16"
• Fuse rating: 2 x 30A
1211a
• 854W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 72dBA (reference 1W into 4 ohms)
• 1300W RMS x 1 channel at 2 ohms, 14.4V supply and
≤1% THD + N
• Dynamic power: 1516W at 2 ohms
• Effective damping factor: 6.357 at 4 ohms
• Frequency response: 17Hz – 302Hz (–3dB)
• Maximum input signal: 5.7V
• Maximum sensitivity: 75mV
• Output regulation: .132dB at 4 ohms
• Dimensions (L x W x H): 12" x 18-1/2" x 2-11/16"
• Fuse rating: 3 x 40A
7521a
• 97W RMS x 2 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 83dBA (reference 1W into 4 ohms)
• 142W RMS x 2 channels at 2 ohms, 14.4V supply and
≤1% THD + N
• 283W RMS x 1 channel at 4 ohms, 14.4V supply and
≤1% THD + N
• Dynamic power: 190W at 2 ohms
• Effective damping factor: 6.389 at 4 ohms
• Frequency response: 10Hz – 69kHz (–3dB)
• Maximum input signal: 5.5V
• Maximum sensitivity: 75mV
• Output regulation: .078dB at 4 ohms
• Dimensions (L x W x H): 12" x 11-7/16" x 2-11/16"
• Fuse rating: 1 x 30A
7541a
• 111W RMS x 4 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 81dBA (reference 1W into 4 ohms)
• 139W RMS x 4 channels at 2 ohms, 14.4V supply and
≤1% THD + N
• 278W RMS x 2 channels at 4 ohms, 14.4V supply and
≤1% THD + N
• Dynamic power: 164W at 2 ohms
• Effective damping factor: 6.315 at 4 ohms
• Frequency response: 10Hz – 100kHz (–3dB)
• Maximum input signal: 5.5V
• Maximum sensitivity: 75mV
• Output regulation: .088dB at 4 ohms
• Dimensions (L x W x H): 12" x 15" x 2-11/16"
• Fuse rating: 2 x 30A
Features, specifications and appearance are subject to change without notice.
ystems, 250 Crossways Park Drive, Woodbury, NY 11797 USA
Infinity S
4.4INF (4463) • F
6.67
51
© 2004 Harman International Industries, Incorporated
Part No. REFAMPOM12/04
AX 516.682.3556 • www.infinitysystems.com
5761a
• 56W x 4 channels and 107W x 2 channels, at 4 ohms and
1% THD + N
≤
• Signal-to-noise ratio: 82dBA (reference 1W into 4 ohms)
• 80W x 4 channels, 150W x 2 channels at 2 ohms, 14.4V supply
and ≤1% THD + N
• 148W x 2 channels, 287W x 1 channel at 4 ohms, 14.4V supply
and ≤1% THD + N
• Dynamic power: 117W (channels 1, 2, 3, 4);
163W (channels 5, 6) into 2 ohms
• Effective damping factor: 6.373 at 4 ohms
• Frequency response: 10Hz – 57kHz (channels 1, 2, 3, 4);
10Hz – 302Hz (channels 5, 6)
• Maximum input signal: 6.3V
• Maximum sensitivity: 75mV
• Output regulation: .063dB at 4 ohms
• Dimensions (L x W x H): 12" x 18-1/2" x 2-11/16"
• Fuse rating: 2 x 30A
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the products described in this
owner
’
s manual are in compliance with technical standards:
EN 55013:2001
EN 55020:2002
Klaus Lebherz
Harman Consumer Group International
Chateau-du-Loir, France 12/04
Loading...