Technical Document
430773-01 Rev. 5
CB966 Wireless Shopper Help Button
Programming and Installation Instructions
Introduction
The CB966 is a 1-button shopper help button with voice assurance which allows shoppers to request assistance at various retail sales floor locations. The CB966 is a member of the Global Solutions Family, which operates in the 800MHz – 900MHz frequency spectrum. GSF Help Buttons are designed to communicate with Indyme’s Smart Response infrastructure.
Programming Parameters
Many of the help buttons are pre-programmed at the factory and labeled with location and address information. If your help button is pre-programmed you can skip ahead to the installation section of these instructions.
CB966 help buttons have three primary programming parameters; Netcode, Address and Operating Mode. These MUST be programmed in the correct order to establish communication and ensure proper operation. Identify the parameters for your configuration before you begin programming.
Using the programming instructions below set the following parameters in order.
•Netcode – unique identification code for the installation environment.
•Address – alarm number associated with a control unit alarm event.
•Operating Mode – defines how the help button will respond when activated.
Programming a help button requires a series of button presses. On the CB966, SET is the “large round button” and RESET is the “raised button on the bottom right”. The assurance LED ring surrounds the SET button. This LED ring will flash during programming to indicate your progress.
Help button Programming
Help buttons use a hierarchy based menu structure. You must enter the Programming Menu first, and then select the desired submenu. Each submenu may have one or more options available. These options are used to assign specific operational characteristics to the help button. Review the submenus/options before you begin programming.
Indyme Solutions, Inc. 8295 Aero Place San Diego, CA 92123 USA |
+1.858.268.0717 +1.800.829.6141 |
Page 1 of 6 |
Technical Document
Programming
Menu
Address |
Learn |
Operation |
Clone |
Menu 1 |
Menu 2 |
Menu 3 |
Menu 7 |
Enter the Programming Menu
Press and hold the RESET button until the assurance LED flashes one time.
Press and hold the SET button, until the assurance LED flashes two times. Press and hold the RESET button, until the assurance LED flashes three times.
The help button is now in the Programming Menu mode, proceed to the desired submenu.
Menu-1: Address Programming
430773-01 Rev. 5
Set
Reset
Assigns the help button to a corresponding alarm event programmed in the control unit. A help button address is a four digit number from 0001 to 4095. Leading zeros are required.
After entering the Programming Menu;
Press the SET button one time for Menu-1, RESET once to select.
The assurance LED will flash one time to indicate Menu-1 was selected. Use SET and RESET to program the 4-digit address as follows;
SET = digits 1-9, RESET = digit 0 and SAVE. Leading zeros are required For example, programAlarm-0802 as follows:
▪Press RESET once to represent the zero. (0)
▪Press SET eight times, RESET once to save. (8)
▪Press RESET once to represent the zero. (0)
▪Press SET two times, RESET once to save. (2)
Note: When the RESET button is pressed to save the 4th digit, the assurance LED will flash to indicate the address that was entered. The assurance LED will indicate digit zero by a long flash. (approximately 1- sec.)
Menu-2: Learn Mode
Allows the help button to capture the Netcode from another GSF device; (help button or access point). All help buttons and access points must have the same Netcode to communicate.
After entering the Programming Menu;
Press the SET button two times for Menu-2, RESET once to select. The LED will flash twice to indicate Menu-2 was selected.
The LED will then begin flashing. ¼ second on, 1 second off. This indicates that the help button is requesting a Netcode. When the help button receives a Netcode, it will flash the assurance LED
Indyme Solutions, Inc. 8295 Aero Place San Diego, CA 92123 USA |
+1.858.268.0717 +1.800.829.6141 |
Page 2 of 6 |
Loading...