Indesit W125TXCH Parts List
Model type:
W125TXCH
Commercial code:
28194
General notes
Technical Documentation guidelines
----------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------
You can find herewith some generic information to simplify cunsulting of technical documentation:
1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not
necessarly have a related spare part for each particular shown on exploded views.
2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find
those codes in the spare parts list with the same reference of particular where spares are installed or with references 099, 999.
Instruction booklets, once managed, appear with 000 reference.
3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of
certain range:some models might have more than an exploded view for a given category, each distinguished by a different serial
no.and linked to another spare parts list, In this case, serial no. is required to supply the right spare part code. Exploded view to be
considered is the one with a more recent serial no. but previous than the one of the model that needs assistance.
4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already
existing numeration references. Revision number of an exploded view is shown into last four digits of serial number into upper
right hand corner.
5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare
part other informations are available:
REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional
characteristics
INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of
information(s) to refer to complete technical intervention, track for changes or to find correct spare part code.
6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in
the best way as possible, it is helpful to pay attention to all notices and constantly verify documentation updates
7.Technical documentation cover shows model name and its commercial codes
mod.W125TXCH page 2
1180110 Exploded views
mod.W125TXCH page 3
1180110 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
000 C00090278 user instructions booklet i-f-d
001 C00046667 wiring stop
001 C00064550 dain hose holder
001 C00064551 wiring stop
002 C00075314 top - white
003 C00075315 1 x C00090578 cabinet n1040276
003 C00090578 1 x C00118608 cabinet white b27
004 C00078644 dashboard + handle
005 C00075317 pushbutton white
006 C00075318 components knob white 27
007 C00075319 wash timer knob white
008 C00075320 door frame assy
009 C00076447 door handle kit
010 C00075324 plinth white
011 C00087084 foot - rear m8 h = 2,3 cm
012 C00059869 spring for foot d =11 mm h = 21
012 C00083828 spring for foot d =11 mm h = 8,5
013 C00075325 hinge door
014 C00002497 nut m4x3,2x7
014 C00019846 civata t 1/2 t m4x12
014 C00065185 bolt m4,5 x 11
015 C00046666 collar for drain hose
016 C00003144 blanking plug 11mm
016 C00065871 blanking plug
016 C00089419 blanking plug 6.5 mm
016 C00089803 blanking plug d = 53 mm
017 C00064501 1 x C00099313 rear cover - white
018 C00084817 blanking plate-rear(test plug)
mod.W125TXCH page 4
1180210 Exploded views
mod.W125TXCH page 5
1180210 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
001 C00064786 1 x C00143260 bolt m8x23 torx tefl
002 C00013563 bearing 25 x52 x 15 6205-2z
003 C00051737 torx m8 x 27 dri-loc screw
003 C00064785 bolt m8x22 tb6lt
004 C00002591 bearing 20x47x14
004 C00044765 bearing 6206-2z n1040300
n1040371
005 C00082696 standard oil seal v4-406 n1040300
n1040371
005 C00096186 standard oil seal cv4 30 x 52/65 x n1040300
n1040326
008 C00088408 bolt + washer
009 C00064517 tank cradle channel-top left right
010 C00064548 upper counterweight 11 kg
011 C00064515 anchorage pad - suspension
012 C00064502 suspension spring - tank
013 C00086430 detergent recovery hose attached
014 C00064545 door bellows seal no deterg. recov n1040282
n1040291
014 C00093345 door bellows seal standard d= 28- n1040282 80281940030
015 C00064546 clamping ring - bellows seal front
016 C00064547 bellows clamp (tank front) n1040291
016 C00092155 bellows clamp (tank front) 80281940030
017 C00064516 1 x C00092178 front counterweight n1040291
017 C00092178 front counterweight 80281940030
018 C00064531 hose tank to filter n1040291
019 C00064518 1 x C00093848 cradle outer- set n1040286
019 C00093848 cradle outer- set n1040325 80281940030
020 C00065152 nut romob m6x22x1,5
021 C00030443 1 x C00047136 nut romob m8 80281940030
021 C00030680 1 x C00040130 nut m 10 n1040286
022 C00086515 shock absorber 80 n (11105) n1040286
022 C00093884 shock absorber 80 n 8.15 mm n1040325
024 C00030446 bolt m10 x 45 zntr n1040286
024 C00093750 bolt zink m8x40 n1040325 80281940030
mod.W125TXCH page 6
1180210 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
025 C00064789 wash paddles (extractable) 46 l
026 C00074217 1 x C00093772 outer tank & inner drum assy n1040256 80281940000
1 x C00094278 n1040291
026 C00092257 1 x C00093772 outer tank & inner drum assy b5 n1040300 80281940030
1 x C00094278 n1040371
026 C00094279 1 x C00094275 outer tank & inner drum assy evo n1040300 80281940030
1 x C00094278 n1040371
027 C00064528 hose dispenser to tank n1040291
028 C00074213 bearing spider assembly n1040300
n1040371
028 C00096077 bearing spider assembly n1040300
029 C00074211 drum pulley d=210 mm h=20 mm
030 C00074218 belt l=1046 - 1051 mm h8
031 C00092174 hose tank to filter oko 80281940030
032 C00092161 hose dispenser to tank 80281940030
033 C00091148 1 x C00094908 clamp d=79 mm
035 C00092411 hose clamp
099 C00001109 loctite 270 10 gr.
099 C00033026 ambljgon grease ta 100 gr.
mod.W125TXCH page 7
1180310 Exploded views
mod.W125TXCH page 8
1180310 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
001 C00090293 supply cable 3x1 (ch) 1,5 m n1040276
001 C00091643 supply cable 3x1 ch 1,5 m +
002 C00019902 plastic -u- to make drain hose
003 C00027466 drain hose - to sink l=1860mm
005 C00063971 on-off switch (unipolar)
005 C00088394 push button switch na idc
006 C00064559 radio interference suppressor
008 C00083916 programme select elbi 1665 rast.2
009 C00084763 pilot light red 12 v idc rast 2.5
009 C00089024 pilot light red 230v ra2,5
012 C00064537 support - pressure switch
013 C00085195 potentiometer 8 pos. idc rast 2,5
015 C00075459 additive container
016 C00075352 1 x C00097732 soap dispenser drawer
017 C00086660 pressure switch 1 level 93-68 + n1040291
017 C00092151 pressure switch 1 l.78-50 n1040299 80281940030
018 C00075351 1 x C00097732 dispenser body n1040291
1 x C00097835
018 C00092314 dispenser body 80281940030
019 C00041785 air trap hose 540 mm. n1040291
019 C00092170 pipe pressostat l= 470mm. evo ii 80281940030
020 C00019755 anti-vibration bush (foam)
021 C00064530 clip-pressure switch tube
022 C00064532 1 x C00092173 air trap n1040291
022 C00092173 air trap x oko 80281940030
025 C00065185 bolt m4,5 x 11
025 C00085194 door interlock
027 C00045023 filter handle
027 C00045025 filter seal
027 C00045027 filter element kit
028 C00064950 self cleaning pump 240v./50hz. n1040291
028 C00076510 1 x C00092264 self cleaning pump 240v./50hz. 80281940030
029 C00074152 bolt m6x30
029 C00084029 bolt motor m6x34
030 C00074151 rubber bush - motor mount
mod.W125TXCH page 9
1180310 Spare parts list
Ref. Code From To S/N Substitute Description Notice Industrial
031 C00074153 spacer motor support l= 187 mm
032 C00040932 self locking nut m6
035 C00043430 1 x C00097257 tacho generator black for ice
035 C00047317 brush for motor
035 C00053050 1 x C00053045 small cover for tachogenerator
035 C00074221 motor n1040258
035 C00088352 brush motor ceset mca
035 C00088356 tacho generator for motor ceset
038 C00086661 heating element for probe 1700w n1040300
038 C00087188 heating elem.termal cut-out n1040300
039 C00058523 pillar retainer-heating element
040 C00090289 eeprom w125txch evo1 sw
043 C00084838 1 x C00093157 universal module (less eeprom)
044 C00066292 insulated tweezers
044 C00084566 1 x C00095669 housing seriale lb2000-pc top
044 C00084943 1 x C00099862 serial cable lb2000 - pc n1040317
045 C00046157 stopper detergent container
046 C00075458 hopper cover 1 ev
047 C00064534 seal - electrovale/dispenser
047 C00066518 2-way electrovalve 1e-2u 7 lt.
048 C00005572 sealing washer-mains inlet hose
049 C00005781 inlet hose filter
050 C00003070 mains inlet hose cold 25c 10bar
051 C00064946 electrovalve support 1 ev
052 C00089859 wiring idc n1040276
054 C00047069 1 x C00097834 additive cover
055 C00086717 bracket for module
055 C00086718 support cover
056 C00083915 temperature sensor ntc elth tl
057 C00092412 hose clamp
058 C00008612 tube clamp 34,6-36,4
mod.W125TXCH page 10
Notices
n1040061: Trouble-shooting.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Intervention procedure on 2000 washing machines
1. Reading the error code
The fault on the appliance is signalled via:
1. the continuous rotation of the selector knob
2. the action, for the first 4', of the electrovalve and the drain pump
3. the door becomes unlocked
4. the led flashes:
the number of flashes indicates the fault code; the code should be read as follows:
· each fast flash (2/3 flashes of the led very close together) represents one code value
· the fault code is evaluated by counting the number of flashes occurring at 3/4" intervals from one another
· stop counting when the washing machine waits the equivalent of approximately 8/9" between flashes
· the procedure is repeated by the appliance cyclically
E.g.: F03
(FIGURE NT 00)
2. Autotest
Should the washing machine not be signalling an error, you can check it using a serial key and using a particular autotest cycle,
which is to be activated as follows:
1. bring the washing machine to reset position (coloured ball) for at least 5" and wait until the led flashes on reset mode
2. insert the hardware key into the serial outlet
3. position the switch situated on the key in TEST position
4. wait for the door to lock and for the selector to start turning
5. position the switch situated on the key in PC position
the appliance will carry out the following cycle:
· selector moves on up to position 0 (12h if the appliance has a delay, programme 1 if it has no delay)
· loads the wash electrovalve for approx. 10"
· loads the pre-wash electrovalve for approx. 10"
· loads the wash electrovalve and pre-wash electrovalve at the same time until the pressure switch is on full
· heats up to 30° and moves the motor in both directions
· selector moves on for 9 notches
· drains and spins
· the selector knob stops on one of the reset positions
· STOP
mod.W125TXCH page 11
Loading...