INDESIT THA 642 IX/I User Manual

THA 642 IX/I
Lietuvių k.
Naudojimo instrukcijos
HOB
Turinys
Naudojimo instrukcijos,1
Įspėjimai,3
Pagalba,4 Prietaiso aprašymas,5 Montavimas,18
Įjungimas ir naudojimas,22 Atsargumo priemonės ir patarimai,22 Techninė priežiūra,23 Gedimų šalinimas,23
English
Operating Instructions
HOB
Contents
Operating Instructions,1 Warnings,2 Assistance,4 Description of the appliance,5 Installation,6 Start-up and use,10 Precautions and tips,10 Maintenance and care,11 Troubleshooting,11
Eesti keeles
Kasutusjuhend
KEEDUPLAAT
Sisukord
Latviešu valoda
Lietošanas instrukcija
PLĪTS VIRSMA
Cuprins
Lietošanas instrukcija,1
Brīdinājumi,3 Palīdzība,4 Ierīces apraksts,5 Ierīkošana,24 Ieslēgšana un lietošana,28 Piesardzības pasākumi un ieteikumi,28 Tehniskā apkope un kopšana,29 Traucējumu novēršana,29
Kasutusjuhend,1 Hoiatused,2 Klienditugi,4 Seadme kirjeldus,5 Paigaldamine,12 Käitamine ja kasutamine,16 Ettevaatusabinõud ja soovitused,16 Hooldus,17 Veaotsing,17
Warnings
Hoiatused
WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in re. NEVER try to extinguish a re with water, but switch off the appliance and then cover ame e.g. with a lid or a re blanket.
WARNING: Danger of re: do not store items on the
cooking surfaces.
Never use steam cleaners or pressure cleaners on the appliance.
Remove any liquid from the lid before opening it. Do not close the glass cover (if present) when the gas burners or electric hotplates are still hot.
The appliance is not intended to be operated by means of an external timer or separate remote control system.
CAUTION: the use of inappropriate hob guards can cause accidents.
HOIATUS: sisselülitatud seade ja selle juurdepääsetavad osad muutuvad kasutamise ajal kuumaks. Olge ettevaatlik ja vältige kontakti kütteelementidega. Alla 8-aastased lapsed tuleb hoida seadmest eemal, v.a. juhul, kui neile on tagatud pidev järelevalve. Vanemad kui 8-aastased lapsed ja isikud, kellel on vähenenud füüsilised või vaimsed võimed või vähesed kogemused ja oskused, võivad seda seadet kasutada juhul, kui on tagatud nende järelevalve ning neile on antud juhised seadme ohutuks kasutamiseks ja nad mõistavad seadme kasutamisest tulenevaid ohte. Lapsed ei tohi seadmega mängida. Lapsed võivad seadet puhastada ja hooldada ainult järelevalve all.
HOIATUS: rasvas või õlis küpseva toidu jätmine keeduplaadile järelevalveta on ohtlik ja võib põhjustada tulekahju. Tulekahju kustutamiseks ÄRGE kasutage vett, vaid lülitage seade välja ja seejärel katke leek näiteks kaane või tuletekiga.
HOIATUS: Tuleoht: ärge hoidke keeduplaatidel mingeid esemeid.
Ärge kasutage seadme puhastamiseks auru- ega survepuhastusseadmeid.
Enne kaane avamist eemaldage sellele kogunenud vedelik. Ärge sulgege klaaskaant (kui on olemas), kui gaasipõletid või elektrilised keeduplaadid on veel kuumad.
Seade ei ole mõeldud kasutamiseks koos välise taimeri ega eraldiseisva kaugjuhtimissüsteemiga.
TÄHELEPANU: valede keeduplaadipiirete kasutamine võib põhjustada õnnetusi.
2
Įspėjimai
Brīdinājumi
ĮSPĖJIMAS! Prietaisas ir jo pasiekiamos dalys naudojant įkaista. Būkite atsargūs, neprisilieskite prie įkaitusių prietaiso dalių. Jaunesni nei 8 metų vaikai gali būti prileidžiami prie prietaiso tik jei juos prižiūri suaugusieji. Vyresni nei 8 metų vaikai ir asmenys, turintys zinių, jutimo ar psichinių sutrikimų arba nepakankamai žinių ar patirties, šiuo prietaisu gali naudotis tik tuomet, jei jie prižiūrimi arba instruktuojami, kaip saugiai naudoti prietaisą, ir supranta kylančias grėsmes. Vaikams turi būti draudžiama žaisti su prietaisu. Neprižiūrimi vaikai taip pat negali valyti prietaiso ar atlikti jo priežiūros darbų.
ĮSPĖJIMAS! Ant įjungtos viryklės palikti indai su riebalais ar aliejumi gali sukelti gaisrą. NIEKADA
nebandykite liepsnos gesinti vandeniu – išjunkite
prietaisą ir kuo nors uždenkite liepsną, pavyzdžiui, dangčiu arba priešgaisriniu apklotu.
ĮSPĖJIMAS! Gaisro pavojus – ant viryklės nelaikykite jokių daiktų.
Niekuomet nevalykite prietaiso gariniais ar slėginiais
valikliais.
Prieš atidarydami gaubtą nuo jo nuvalykite skysčius. Neuždenkite stiklinio dangčio (jei sumontuotas), kol neatvėso dujiniai degikliai arba elektrinė kaitlentė.
Prietaisas nevaldomas išoriniu laikmačiu arba atskira
nuotoline valdymo sistema.
ATSARGIAI! Netinkamų viryklės apsaugų naudojimas gali sukelti nelaimingą atsitikimą.
BRĪDINĀJUMS! Ierīce un tās atklātās daļas lietošanas laikā stipri sakarst. Nepieskarieties sakarsušajām ierīces daļām. Bērni, kuri ir jaunāki par astoņiem gadiem, drīkst atrasties ierīces tuvumā tikai stingrā pieaugušo uzraudzībā. Ierīci drīkst lietot bērni, kuri ir sasnieguši astoņu gadu vecumu, bet personas ar ierobežotām ziskajām, maņu vai garīgajām spējām un personas, kurām nav ierīces lietošanas pieredzes vai nepieciešamo zināšanu, - tikai tad, ja tās tiek uzraudzītas vai ir atbilstoši informētas par ierīces drošu lietošanu un iespējamajiem riskiem. Bērni nedrīkst rotaļāties ar ierīci. Bērni nedrīkst bez uzraudzības tīrīt ierīci un veikt tās apkopi.
BRĪDINĀJUMS! Atstājot uz ieslēgtas plīts virsmas pannu ar taukiem vai eļļu, varat radīt ugunsgrēka risku. NEKĀDĀ GADĪJUMĀ nemēģiniet dzēst uguni ar ūdeni, bet izslēdziet plīti un nosedziet liesmu ar vāku vai nedegošu pārsegu.
BRĪDINĀJUMS! Aizdegšanās risks: neglabājiet priekšmetus uz plīts virsmas.
Ierīci nedrīkst tīrīt ar tvaika vai augstspiediena tīrītājiem.
Pirms pārsega atvēršanas notīriet no tā visu šķidrumu. Ja gāzes degļi vai elektriskās sildvirsmas joprojām ir karstas, stikla pārsegu (ja tāds ir) nedrīkst aizvērt.
Iekārtu nav paredzēts lietot kopā ar ārējo taimeri vai atsevišķu tālvadības ierīci.
UZMANĪBU! Neatbilstošu plīts virsmas aizsargu lietošana var izraisīt nelaimes gadījumus.
3
Assistance
Communicating:
Type of trouble
Appliance model (Mod.)
Serial number (S/N) This information is found on the data plate located on the appliance and/or on the packaging.
Klienditugi
Hoidke käepärast järgmised andmed:
tüüpi anomaalia
seadme mudel (Mod.)
seerianumber (S/N) Need andmed leiate seadme andmeplaadilt ja/või pakendilt.
Pagalba
Informacija:
tipas anomalija
prietaiso modelis (Mod.)
Serijos numeris (S/N)
Šią informaciją rasite duomenų plokštelėje, kuri yra ant prietaiso ir (arba) pakuotės.
Palīdzība
Paziņojums:
tipa anomālija
ierīces modelis (Mod.)
sērijas numurs (S/N)
Šī informācija ir norādīta uz tehnisko datu plāksnītes, kas piestiprināta ierīcei un/vai tās iepakojumam.
4
Description of the appliance
5
2
1
3
Prietaiso aprašymas
Overall view
1. Support Grid for COOKWARE
2. GAS BURNERS
3. Control Knobs for GAS BURNERS
4. Ignition for GAS BURNERS
5. SAFETY DEVICES
GAS BURNERS differ in size and power. Use the diameter of the cookware
to choose the most appropriate burner to cook with.
• Control Knobs for GAS BURNERS for ame adjustment.
GAS BURNER IGNITION enables a specic burner to be lit automatically.
SAFETY DEVICE stops the gas flow if the flame is accidentally
extinguished.
Seadme kirjeldus
Ülevaade
1. Rest KEEDUNÕU JAOKS
2. GAASIPÕLETID
3. GAASIPÕLETITE REGULEERIMISE NUPUD
4. GAASIPÕLETITE SÜÜTENUPP
5. OHUTUSSEADISED
Bendras vaizdas
1. GAMINIMO INDO laikančiosios grotelės
2. DUJŲ DEGIKLIAI
3. DUJINIŲ DEGIKLIŲ valdymo rankenėlės
4. DUJINIŲ DEGIKLIŲ uždegimo funkcija
5. SAUGOS ĮTAISAI
DUJINIAI DEGIKLIAI skiriasi dydžiu ir galia. Naudokite tokio skersmens
gaminimo indus, kurie geriausiai tinka tam tikram degikliui.
DUJINIŲ DEGIKLIŲ valdymo rankenėlės liepsnai reguliuoti.
DUJINIO DEGIKLIO UŽDEGIMO FUNKCIJA suteikia galimybę
automatiškai uždegti tam tikrą degiklį.
APSAUGINIS ĮTAISAS sustabdo dujų srautą, jei liepsna netyčia užgęsta.
Ierīces apraksts
Vispārīga informācija
1. GATAVOŠANAS TRAUKU balsta režģis
2. GĀZES DEGĻI
3. GĀZES DEGĻU vadības slēdži
4. Aizdedzes GĀZES DEGĻIEM
5. DROŠĪBAS IERĪCES
GAASIPÕLETID on erineva suuruse ja võimsusega. Kasutage põleti jaoks
kõige sobivama läbimõõduga keedunõud.
GAASIPÕLETITE REGULEERIMISE NUPUD leegi reguleerimiseks.
GAASIPÕLETI SÜÜTENUPP võimaldab vastava põleti automaatselt
süüdata.
OHUTUSSEADIS seiskab gaasivoolu, kui leek peaks juhuslikult kustuma.
GĀZES DEGĻIEM ir dažādi izmēri un jauda. Gatavojot izvēlieties
gatavošanas trauka diametram atbilstošāko degli.
GĀZES DEGĻU vadības slēdži liesmas regulēšanai.
GĀZES DEGĻA AIZDEDZE ļauj automātiski aizdedzināt īpašu degli.
DROŠĪBAS IERĪCE aptur gāzes plūsmu, ja liesma tiek nejauši nodzēsta.
4
5
Installation
Top 20 mm
Top 30-50 mm
GB
! Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance.
! Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.
Positioning
! Keep packaging material out of the reach of children. It can become a choking
or suffocation hazard (see Precautions and tips).
! The appliance must be installed by a qualied professional according to the
instructions provided. Incorrect installation may cause harm to people and animals or may damage property.
! This unit may be installed and used only in permanently ventilated rooms in accordance with current national regulations. The following requirements must be observed:
• The room must be equipped with an air extraction system that expels any combustion fumes. This may consist of a hood or an electric fan that automatically starts each time the appliance is switched on.
Fitting the appliance
The following precautions must be taken when installing the hob:
• Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 200 mm from the edge of the hob.
• Hoods must be installed according to their relative installation instruction
manuals and at a minimum distance of 650 mm from the hob (see gure).
• Place the wall cabinets adjacent to the hood at a minimum height of 420
mm from the hob (see gure).
If the hob is installed beneath a wall cabinet, the latter must be situated at a minimum of 700
600mm min.
650mm min.
mm above the hob.
420mm min.
• The installation cavity should have the dimensions indicated in the gure.
NOTE: In case of installation of a hood above the hob, please refer to the hood instructions for the correct distance.
In a chimney stack or branched flue. (exclusively for cooking appliances)
Directly to the Outside
• The room must also allow proper air circulation, as air is needed for
combustion to occur normally. The ow of air must not be less than 2 m3/h
per kW of installed power.
The air circulation system may take air directly from the outside by means of a pipe with an inner cross section of at least 100 cm
2
; the
opening must not be vulnerable to any type
Examples of ventilation holes for comburant air.
Adjacent Room
A
Room to be Vented
of blockages.
The system can also provide the air needed for combustion indirectly, i.e. from adjacent rooms
tted with air circulation tubes as described
above. However, these rooms must not be communal rooms, bedrooms or rooms that
may present a re hazard.
Enlarging the ventilation slot between window and floor.
• Intensive and prolonged use of the appliance may necessitate supplemental ventilation, e.g. opening a window or increasing the power of the air intake system (if present).
• Liquid petroleum gas sinks to the oor as it is heavier than air. Therefore,
rooms containing LPG cylinders must also be equipped with vents to allow gas to escape in the event of a leak. As a result LPG cylinders, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc.). It is advisable to keep only the cylinder being used in the room, positioned so that it is not
subject to heat produced by external sources (ovens, replaces, stoves,
etc. ) which could raise the temperature of the cylinder above 50°C.
• After having cleaned the perimeter surface, apply the supplied gasket to
the hob as shown in the gure.
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward
extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws
in accordance with the thickness of the worktop (see the following gures).
• Where the hob is not installed over a built-in oven, a wooden panel must be installed as insulation. This must be placed at a minimum distance of 20 mm from the lower part of the hob.
6
Ventilation
! The cable must not be bent or compressed. To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of
wood, or on a completely at surface with an opening of at least 45 x 560
! The cable must be checked regularly and replaced by authorised technicians
only (see Assistance). mm (see diagrams).
! The manufacturer declines any liability should these safety measures not
be observed.
45 mm.
560 mm.
Gas connection
The appliance should be connected to the main gas supply or to a gas
cylinder in compliance with current national regulations. Before carrying out
the connection, make sure the cooker is compatible with the gas supply you
Where a hob is installed above an oven without a forced ventilation cooling system, adequate ventilation must be provided inside the cabinet by means
of air holes through which air can pass (see gure).
wish to use. If this is not the case, follow the instructions indicated in the
paragraph “Adapting to different types of gas.”
When using liquid gas from a cylinder, install a pressure regulator which
complies with current national regulations.
! Check that the pressure of the gas supply is consistent with the values
indicated in Table 1 (“Burner and nozzle specications”). This will ensure the
safe operation and longevity of your appliance while maintaining efcient
energy consumption.
Connection with a rigid pipe (copper or steel)
! Connection to the gas system must be carried out in such a way as not to
place any strain of any kind on the appliance.
There is an adjustable L-shaped pipe tting on the appliance supply ramp
and this is tted with a seal in order to prevent leaks. The seal must always
Electrical connection
Hobs equipped with a three-pole power supply cable are designed to operate
be replaced after rotating the pipe tting (seal provided with appliance). The
gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.
with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). The earth wire in the cable has a green and yellow cover. If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier.
Connecting a flexible jointless stainless steel pipe to a threaded
attachment
The gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.
These pipes must be installed so that they are never longer than 2000 mm
when fully extended. Once connection has been carried out, make sure that
the exible metal pipe does not touch any moving parts and is not compressed.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indicated on the data
! Only use pipes and seals that comply with current national regulations. plate.
The appliance must be directly connected to the mains using an omnipolar
circuit-breaker with a minimum contact opening of 3 mm installed between
the appliance and the mains.
Checking the tightness of the connection
! When the installation process is complete, check the pipe ttings for leaks
using a soapy solution. Never use a ame.
The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C.
Adapting to different types of gas
To adapt the hob to a different type of gas other than default type (indicated
on the rating plate at the base of the hob or on the packaging), the burner
nozzles should be replaced as follows:
! The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations.
1. Remove the hob grids and slide the burners off their seats.
2. Unscrew the nozzles using a socket spanner of the appropriate size, and replace them with nozzles for the new type of gas (see table 1 “Burner
Before connecting to the power supply, make sure that:
• the appliance is earthed and the plug is compliant with the law.
• the socket can withstand the maximum power of the appliance, which is indicated on the data plate.
• the voltage is in the range between the values indicated on the data plate.
and nozzle characteristics”).
3. Reassemble the parts following the above procedure in the reverse order.
4. Once this procedure is nished, replace the old rating sticker with one
indicating the new type of gas used. Sticker are available from any of our Service Centres.
• the socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.
• Adjusting the burners’ primary air Does not require adjusting.
GB
! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.
7
• Setting the burners to minimum
GB
1. Turn the tap to the low ame position;
2. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap
pin, until the ame is small but steady.
3. Having adjusted the ame to the required low setting, while the burner is
alight, quickly change the position of the knob from minimum to maximum
and vice versa several times, checking that the ame does not go out.
4. Some appliances have a safety device (thermocouple) tted. If the device
fails to work when the burners are set to the low ame setting, increase this low ame setting using the adjusting screw.
5. Once the adjustment has been made, replace the seals on the by-passes
using sealing wax or a similar substance.
! If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible.
! Once this procedure is nished, replace the old rating sticker with one
indicating the new type of gas used. Stickers are available from any of our Service Centres.
! Should the gas pressure used be different (or vary slightly) from the
recommended pressure, a suitable pressure regulator must be tted to the
inlet pipe (in order to comply with current national regulations).
DATA PLATE Electrical
connections
see data plate
ECODESIGN
This appliance conforms to the EU Regulation no. 66/2014 implementing Directive 2009/125/EC. standard EN 30-2-1
8
Burner and nozzle specifications
Table 1
ELECTRIC SUPPLY: 220-240V~ 50/60Hz 0,6W
GB
CATEGORY II2H3+
TYPE OF GAS
USED
NATURAL GAS (Methane)
LIQUEFIED PETROLEUM GAS (Butane)
LIQUEFIED PETROLEUM GAS (Propane)
Type of gas used
G20 20 mbar 1R - 2S -1A 7.30 695 l/h 9.52 G30 28-30 mbar G31 37 mbar
G20
G30
G31
TYPE OF
NOZZLE RATED
BURNER
Rapid
Semi-Rapid
Auxiliary
Rapid
Semi-Rapid
Auxiliary
Rapid
Semi-Rapid
Auxiliary
Model configuration
4 BURNERS
1R - 2S -1A
1R - 2S -1A
RATED
THERMAL
CONSUMPTION
FLOW RATE
kW
115Y
95Z 72X
85 63 50
85 63 50
7.30 531 g/h 30.94
7.30 521 g/h 23.80
3.00
1.65
1.00
3.00
1.65
1.00
3.00
1.65
1.00
Rated thermal
owrate (kW)
286 l/h 167 l/h
95 l/h
218 g/h 127 g/h
73 g/h
214 g/h 125 g/h
71 g/h
REDUCED
HEAT
CAPACITY
0.75
0.40
0.40
0.75
0.40
0.40
0.75
0.40
0.40
Total rated
consumption
kW
GAS PRESSURE
min. rat. max.
17 20 25
20 28-30 35
25 37 45
Air required (m³) for burning1m³ of gas
mbar
S
S
R
A
THA 642 IX/I
9
Start-up and use
Rapid (R)
Semi Rapid (S)
Auxiliary (A)
Ø Cookware Diameter (cm)
24 - 26
16 - 22
8 - 14
Burner
GB
Precautions and tips
! The position of the corresponding gas burner is shown on every knob.
Gas burners
Each burner can be adjusted to one of the following settings using the corresponding control knob:
Off
Maximum
Minimum
To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting.
Since the burner is tted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the ame alight to heat up.
Models are equipped with an ignition button incorporated into the control knob. If this is the case, the ignitor is present, but not the button. To light a burner, simply press the corresponding knob all the way in and then turn it in the counter-clockwise direction to the “High” setting, keeping it pressed in until the burner lights.
! If a ame is accidentally extinguished, turn off the control knob and wait for
at least 1 minute before trying to relight it.
To switch off the burner, turn the knob in a clockwise direction until it stops
(when reaches the “●” position).
Practical advice on using the burners
To ensure the burners operate efciently:
• Use appropriate cookware for each burner (see table) so that the ames
do not extend beyond the bottom of the cookware.
• Always use cookware with a at base and a cover.
• When the contents of the pan reach boiling point, turn the knob to minimum.
To identify the type of burner, refer to the designs in the section entitled, “Burner
and Nozzle Specications”.
• For maximum stability, always make sure that the pan supports are
correctly tted and that each pan is placed centrally over the burner.
• Pan handles should be positioned in line with one of the support bars on the pan support grid.
• Pan handle should be positioned so not to protrude beyond the front edge of the hob.
The more variable aspect in terms of pan stability can often be the pan itself, (or the positioning of that pan during use).
Well balanced pans, with at bases that
are placed centrally over the burner, with the pan handles aligned with one
of the support ngers obviously offer the
greatest stability.
10
! This appliance has been designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully.
General safety
• This is a class 3 built-in appliance.
• Gas appliances require regular air exchange to maintain efcient operation. When installing the hob, follow the instructions provided in the paragraph on “Positioning” the appliance.
• These instructions are only valid for the countries whose symbols
appear in the manual and on the serial number plate.
• The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use.
• The appliance must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with wet or damp hands and feet.
• The appliance must be used by adults only for the preparation of food, in accordance with the instructions outlined in this booklet. Any other use of the appliance (e.g. for heating the room) constitutes improper use and is dangerous. The manufacturer may not be held liable for any damage resulting from improper, incorrect and unreasonable use of the appliance.
• Ensure that the power supply cables of other electrical appliances do not come into contact with the hot parts of the oven.
• The openings used for ventilation and dispersion of heat must never be covered.
• Always make sure the knobs are in the “●”/“” position when the appliance is not in use.
• When unplugging the appliance always pull the plug from the mains socket, do not pull on the cable.
• Never carry out any cleaning or maintenance work without having detached the plug from the mains.
• In case of malfunction, under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or further malfunctioning of the appliance. Contact a Service Centre (see Assistance).
• Do not close the glass cover (if present) when the gas burners or electric hotplates are still hot.
• The appliance should not be operated by people (including children) with reduced physical, sensory or mental capacities, by inexperienced individuals or by anyone who is not familiar with the product. These individuals should, at the very least, be supervised by someone who assumes responsibility for their safety or receive preliminary instructions relating to the operation of the appliance.
• Do not let children play with the appliance.
• The appliance is not intended to be operated by means of an external
timer or separate remote-control system.
Disposal
• When disposing of packaging material: observe local legislation so that the packaging may be reused.
• The European Directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.
Loading...
+ 22 hidden pages