Indesit PC 640 X-HA, PC 640 T X-HA, PC 640-HA, PC 640 T -HA User Manual

Operating Instructions

HOB

GB

TR

Türkçe,11English,1

PC 640/HA
PC 640 X/HA
PC 640 T X/HA
PC 640 T /HA

Contents

GB

Installation, 2-5

Positioning
Electrical connection
Gas connection
Data plate
Burner and nozzle specifications

Description of the appliance, 6

Overall view

Start-up and use, 7

Practical advice on using the burners

Precautions and tips, 8

General safety
Disposal

Maintenance and care, 9

Switching the appliance off
Cleaning the appliance
Gas tap maintenance

Troubleshooting, 10

1

Installation

Enlarging the ventilation slot
between window and floor.

Adjacent
Room

Room to be
Vented

A

Examples of ventilation holes
for comburant air.

In a chimney stack or branched flue.
(exclusively for cooking appliances)

Directly to
the Outside

600mm min.

600mm min.

700mm min.

GB

! Before operating your new appliance please read this
instruction booklet carefully. It contains important information
for safe use, installation and care of the appliance.

! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.

Positioning

! Keep packaging material out of the reach of children. It
can become a choking or suffocation hazard (see
Precautions and tips).

! The appliance must be installed by a qualified professional
according to the instructions provided. Incorrect installation
may cause harm to people and animals or may damage
property.

! This unit may be installed and used only in permanently
ventilated rooms in accordance with British Standard Codes
Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891
Current Editions. The following requirements must be
observed:

• The room must be equipped with an air extraction system
that expels any combustion fumes. This may consist of a
hood or an electric fan that automatically starts each time
the appliance is switched on.

also be equipped with vents to allow gas to escape in the
event of a leak. As a result LPG cylinders, whether
partially or completely full, must not be installed or stored
in rooms or storage areas that are below ground level
(cellars, etc.). It is advisable to keep only the cylinder
being used in the room, positioned so that it is not
subject to heat produced by external sources (ovens,
fireplaces, stoves, etc. ) which could raise the
temperature of the cylinder above 50°C.

Fitting the appliance

Gas and mixed hobs are manufactured with type X degree
protection against overheating. The following precautions
must be taken when installing the hob:

• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm from the
edge of the hob.

• Hoods must be installed according to their relative
installation instruction manuals and at a minimum
distance of 650 mm from the hob.

• Place the wall cabinets adjacent to the hood at a
minimum height of 420 mm from the hob (see figure).

If the hob is installed beneath a
wall cabinet, the latter must be
situated at a minimum of 700 mm
above the hob (see figure).

• The room must also allow proper air circulation, as air is
needed for combustion to occur normally. The flow of air

3

must not be less than 2 m

/h per kW of installed power.
The air circulation system may
take air directly from the outside
by means of a pipe with an inner
cross section of at least 100 cm
the opening must not be
vulnerable to any type of
blockages.

The system can also provide the
air needed for combustion
indirectly, i.e. from adjacent rooms
fitted with air circulation tubes as
described above. However, these
rooms must not be communal
rooms, bedrooms or rooms that
may present a fire hazard.

• Liquid petroleum gas sinks to the floor as it is heavier
than air. Therefore, rooms containing LPG cylinders must

• The installation cavity should have the dimensions
indicated in the figure.
Fastening hooks are provided, allowing you to fasten the
hob to tops that are between 20 and 40 mm thick. To
ensure the hob is securely fastened to the top, we
recommend you use all the hooks provided.

555 mm

2

;

55 mm

475 mm

Hook fastening diagram

Hooking position Hooking position
for top H=20 mm for top H=30 mm

2

Front

560 mm.

45 mm.

Hooking position Back
for top H=40 mm

! Use the hooks contained in the “accessory pack”

• Where the hob is not installed over a built-in oven, a
wooden panel must be installed as insulation. This
must be placed at a minimum distance of 20 mm from
the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (see diagrams).

When installing the cooktop above a built-in oven
without forced ventilation, ensure that there are air
inlets and outlets for ventilating the interior of the
cabinet adequately.

Electrical connection

Hobs equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage
and frequency indicated on the data plate (this is located
on the lower part of the appliance). The earth wire in the
cable has a green and yellow cover. If the appliance is to
be installed above a built-in electric oven, the electrical
connection of the hob and the oven must be carried out
separately, both for electrical safety purposes and to
make extracting the oven easier.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load
indicated on the data plate.
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum contact
opening of 3 mm installed between the appliance and the
mains. The circuit-breaker must be suitable for the charge
indicated and must comply with current electrical
regulations (the earthing wire must not be interrupted by the
circuit-breaker). The supply cable must not come into
contact with surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical
connection has been made and that it is compliant with
safety regulations.
Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with
the law.

• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated
on the data plate.

• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.

! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).
! The manufacturer declines any liability should these safety

measures not be observed.

Gas connection

The appliance should be connected to the main gas supply
or to a gas cylinder in compliance with current national
regulations. Before carrying out the connection, make sure
the cooker is compatible with the gas supply you wish to
use. If this is not the case, follow the instructions indicated in
the paragraph “Adapting to different types of gas.”
When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.

! Check that the pressure of the gas supply is consistent
with the values indicated in Table 1 (“Burner and nozzle
specifications”). This will ensure the safe operation and
longevity of your appliance while maintaining efficient
energy consumption.

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such
a way as not to place any strain of any kind on the
appliance.

GB

3

GB

There is an adjustable L-shaped pipe fitting on the
appliance supply ramp and this is fitted with a seal in
order to prevent leaks. The seal must always be replaced
after rotating the pipe fitting (seal provided with
appliance). The gas supply pipe fitting is a threaded 1/2
gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a
threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas cylindrical
male attachment.
These pipes must be installed so that they are never
longer than 2000 mm when fully extended. Once
connection has been carried out, make sure that the
flexible metal pipe does not touch any moving parts and
is not compressed.

! Only use pipes and seals that comply with current
national regulations.

Checking the tightness of the connection

! When the installation process is complete, check the
pipe fittings for leaks using a soapy solution. Never use a
flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than
default type (indicated on the rating plate at the base of
the hob or on the packaging), the burner nozzles should
be replaced as follows:

1. Remove the hob grids and slide the burners off their
seats.

2. Unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of gas
(see table 1 “Burner and nozzle characteristics”).

3. Reassemble the parts following the above procedure in
the reverse order.

4. Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of
their housing. The burner consists of two separate parts
(see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner.
Replace the nozzles with models that are configured
for use with the new type of gas (see Table 1). The two
nozzles have the same hole diameter.

3. Replace all the components by completing the above
operations in reverse order.

• Adjusting the burners’ primary air :
Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust
the adjustment screw, which is
positioned in or next to the tap
pin, until the flame is small but
steady.

3. Having adjusted the flame to the required low setting,
while the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out.

4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are
set to the low flame setting, increase this low flame
setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax or a similar
substance.

! If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.

! Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.

! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet pipe (in order
to comply with current national regulations).

4

Burner and nozzle specifications

Table 1 Liquid Gas Natural Gas

Burner Diameter Thermal Thermal By-pass Nozzle Flow* Thermal Nozzle Flow*
power power 1/100 1/100 (g/h) power 1/100 (l/h)
kW kW kW
(p.c.s.*) (p.c.s.*) (p.c.s.*)
(mm) Reduced Nominal (mm) (mm) *** ** Nominal (mm)

GB

Fast (R)

Reduced Fast (RR)

Semi Fast (S)

Auxiliary (A)

Triple Crown (TC)

Supply pressures

* At 15°C and 1013 mbar - dry gas
** Propane P.C.S. = 50.37 MJ/Kg
*** Butane P.C.S. = 49.47 MJ/Kg
Natural P.C.S. = 37.78 MJ/m³

A

R

S

PC 640 X/HA
PC 640 /HA

100

100

75

55

130

0.70

0.70

0.40

0.40

1.50

A

S

RR

S

PC 640 T X/HA
PC 640 T /HA

3.00

2.60

1.65

1.00

3.30

Nominal (mbar)

Minimum (mbar)

Maximum (mbar)

TC

39

39

28

28

61

86

80

64

50

65x2

218

189

120

73

240

28-30

20
35

214

186

118

71

236

37
25
45

3.00

2.60

1.65

1.00

3.30

132 (H)

122 (H)

96

79 (6)

103x2

286

248

157

95

343

20
17
25

DATA PLATE

Electrical
connections

see data plate

This appliance conforms to the following
European Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments

- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments

- 93/68/EEC dated 22/07/93 and
subsequent amendments.

- 2009/142/EEC dated 30/11/09 (Gas) and
subsequent amendments.

- 2002/96/EC and subsequent
amendments.

5

Description of the
appliance

GB

Overall view

GAS BURNERS

Support Grid for

COOKWARE

Control Knobs for

GAS BURNERS

SAFETY

DEVICES *

• GAS BURNERS differ in size and power. Use the
diameter of the cookware to choose the most
appropriate burner to cook with.

• Control Knobs for GAS BURNERS adjust the size
of the flame.

6

Ignition for

GAS BURNERS *

• GAS BURNER ignition* enables a specific burner
to be lit automatically.

• SAFETY DEVICE* stops the gas flow if the flame
is accidentally extinguished.

Only available on certain models.

*