50cm Free Standing Gas Cooker
Instructions for installation and use
KD3G2/G
KD3G21/G
Contents
Introduction 3
Installation 4
Safety Information 10
Features 12
Control Panel 13
Use of hotplates 14
Grilling 15
Oven 16
Oven cooking charts 17
Care and Cleaning 18
Cooking Results Not Satisfactory? 19
Something Wrong With Your Cooker? 20
If it Still W on’t W ork... 21
Technical Characteristics 22
Key Contacts Back Cover
You must read these instructions prior to using your appliance and retain them
for future use.
2
Introduction
Your new appliance is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance
has been installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The cooker is designed specifically for domestic use and responsibility will not be accepted for use in any other
installation.
When the cooker is first used an odour may be emitted,
this will cease after a period of use.
When first using the cooker ensure that the room is well ventilated (e.g. open a window or use an extractor fan) and
that persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed from the
room until the smell has ceased. This odour is due to temporary finish on oven liners and elements and also any
moisture absorbed by the insulation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with the Users Instruction Book.
(b) Has been properly connected to a suitable supply voltage as stated on the
rating plate attached to this equipment.
(c) Has not been subjected to misuse or accident or been modified or repaired by
any person other than the authorised employee or agent.
(d) Has been correctly installed.
1
This appliance is intended for nonprofessional use within the home.
2 These instructions are only for those countries whose symbols appear in the booklet and on the serial no. plate
of the appliance.
3 This owner’ s manual is for a c lass 1 appliance (insulated) or class 2, subc lass 1 appliances (installed
between two cabinets.
3
Installation
The appliance must only be installed by a competent person. In the UK, CORGI registered installers undertake
to work to safe and satisfactory standards.
Before moving your cooker check that it is cool, and switch off at the cooker control unit. Movement of your cooker is
most easily achieved by lifting the front as follows:
Open the grill door sufficiently to allow a comfortable grip on the underside front edge of the oven roof, avoiding any
grill elements.
Note: Take care in moving the cooker as it is heavy. Take care to ensure that any floor covering is not damaged.
(FIG. C)
Splashplate optional, apply to Parts Department (see Back Cover for contact number.)
The following instructions should be read by a qualified technician to ensure that the appliance is installed,
regulated and technically serviced correctly in compliance with current regulations.
Important: remember to unplug the appliance from the mains before regulating the appliance or
carrying out any maintenance work.
Positioning
Important: this unit may be installed and used only in permanently ventilated rooms according to the British
Standards Codes Of Practice: B .S. 6172/B.S . 5440, P ar. 2 and B.S. 6891 Current Editions . The following requirements
must be observed:
a) The cooker should not be installed in a bed sitting room with a volume of less than 20m3. If it is installed in a
room of volume less than 5m3 an air vent of effective area of 110cm2 is required, if it is installed in a room of
volume between 5m3 and 10m3 a supplementary airvent area of 50cm2 is required, if the volume exceeds 11m
no airvent is required. Ho wev er, if the room has a door or a windo w which opens directly to the outside no air
vent is required even when the volume is between 5m3 and 11m3.
b) During prolonged use of the appliance you may consider it necessary to open a window to the outside to
improve ventilation.
c) If there are other fuel burning appliances in the same room, B.S.5440 Par t 2 Current Edition, should, be
consulted to determine the requisite air vent requirements.
3
Installation of the cooker
For a correct installation of the cooker the following precautions must be followed:
The height of the cooker can be adjusted by means of adjustable feet in the plinth (900mm - 915mm). Adjust the feet by
tilting the cooker from the side. Then install the product into position.
NOTE: This appliance must not be fitted on a platform.
The cooker is designed to fit between kitchen cabinets spaced 500mm apart. The space either side need only be sufficient
to allow withdrawal of the cooker for servicing. It can be used with cabinets one side or both as well as in a corner setting.
It can also be used free-standing.
Adjacent side walls which project above hob level, must not be nearer to the cooker than 150mm and should be protected
by heat resistant material. Any overhanging surface or cooker hood should not be nearer than 650mm. (Fig.A)
a) The cooker may be located in a kitchen, a kitonen/diner or bed sitting room, but not in a bathroom or
shower room.
b) The hoods must be installed according to the requirements in the hood handbook.
c) The wall in contact with the back of the cooker must be of flameproof material.
d) The cooker is fitted with a safety chain that must be attached to a hook, secured to the wall behind the
appliance.
Note: some models can have their gas connection inv erted. It is important to make sure the safety chain
is always situated on the side which corresponds to the hose holder (Fig. B).
150 mm
150 mm
650 mm
Fig. A Fig. B Fig. C
4
Gas connection
The cooker should be connected to the gas-supply by a corgi registered installer . During installation of this
product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience
of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be
carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable
to the type of gas to be used. If not, f ollow the instructions indicated in the paragraph headed “Adaptation to
different gas types”. On some models the gas supply can be connected on the left or on the right, as
necessary; to change the connection, reverse the position of the hose holder with that of the cap and
replace the gasket (supplied with the appliance). In the case of connection to liquid gas, by tank, use
pressure regulators that conform to the regulation in force. The gas supply must be connected to the left of
the appliance. Be sure that the hose does not pass through the rear of the cook er touching hot parts.
HOT PARTS
Important: make sure the supply pressure conforms with the values shown in the table entitled “Caracteristics of
the burners and nozzles”. When the cooker is installed between cabinets (recessed), the gas connection
must be effected by an appr oved flexible hose with bay onet fitting (BS 669 Current Edition). The gas inlet
for the cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
T o mak e the connection, a flexib le hose should be used corresponding to the current gas regulations which are:
• the hose must never be at an y point in its lenght in contact with the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or torsional stress and it must not have an y e xcessiv ely narrow
curves or bottlenecks;
• the hose must be easy to inspect along its entire length to check its condition;
• the hose must always be in good condition, ne v er attempt to repair .
Important: the installation must comply with gas safety (installation and use) regulations 1984. In all cases for the
above, b y low , a qualified, corgi approv ed engineer must be called f or installation.
Important: Before using the oven, position the oven burner deflector "A" (provided with the appliance) in the
correct place by inserting the lower tab into the support slot (see figure).
A
5
Electrial connection
Pow er supply voltage and frequency: 230-240V a.c. 50 Hz.
Note: the supply cable must be positioned so that it ne ver reaches at any point a temper ature 50°C higher than
the room temperature. The cable must be routed a way from the rear v ents. Should you require it, y ou may use a
longer cable, howe ver , you must ensure that the cable supplied with the appliance is replaced by one of the same
specifications in accordance with current standards and legislation.
Y our appliance is supplied with a 13 amp fused plug that can be plugged into a 13 amp soc ket for immediate use.
Before using the appliance please read the instructions below .
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse
cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct colour as indicated b y the coloured marking or the
colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your
nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug and y ou should wish to remov e it to add a cable e xtension
or to re-route the mains cable through partitions, units etc., please ensure that either:
• the plug is replaced by a fused 13 amp re-wireable plug bearing the BSI mark of approval.
or:
• the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the appliance.
Please note: for appliances with a rating greater than 13 amp (eg: electric hob, doub le ov ens and freestanding
electric cookers etc.) the mains cable must be wired into a cooker output point with a r ating of 45 amp. In this case
the cable is not supplied.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally
inserted into a socket. Instructions for connecting cab le to an alternative plug:
Important: the wires in the mains lead are coloured in accordance with the following code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
If the colours of the wires in the mains lead do not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked “E” or or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse. A 15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt about the electrical supply
to your machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with the following code:
BLUE “NEUTRAL” (“N”)
BROWN “LIVE” (“L”)
GREEN AND YELLOW “EARTH” (“E”)
GREEN &
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
6
Disposing of the appliance
When disposing of the appliance please remove the plug by cutting the mains cab le as close as possible to the
plug body and dispose of it as described above.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced
(indicated on the label attached to the lid), follow these steps:
a) replace the hose holder mounted on the appliance with that supplied in the bag of “cooker accessories”.
b) Replacing the burner nozzles on the hob:
• remove the grids and slide the b urners from their housings;
• unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of
gas (see table 1 “Burner and nozzle characteristics”).
• replace all the components by repeating the steps in reverse order.
c) Minimum regulation of the hob burners:
•
turn the tap to minimum;
• remove the knob and adjust the regulation screw, which is positioned in or next to the tap pin, until the
flame is small but steady.
N.B.: in the case of liquid gas, the regulation screw must be scre wed in to the bottom.
• check that the flame does not turn off when you turn the tap quickly from high to low.
d) Regulating the primary air of the burners:
The primary air of the burners requires no regulation.
Adapting to different types of gas
In order to adapt the oven to a different type of gas with respect to the gas for which it was manufactured
(indicated on the label), follow these simple steps:
a) Replacing the oven burner nozzle
· open the oven door fully
· pull out the sliding oven bottom
· unscrew the burner fastening screws
V
V
7
· remove screw “V” and then the oven burner;
· Unscrew the oven b urner nozzle using the socket spanner for the nozzles “Z”, or a 7 mm sock et spanner,
and replace it with a nozzle suited to the new type of gas (see Table 1).
T ake particular care handling the spark plug wires and the thermocouple pipes.
· Replace all the parts, following the steps described above in the rev erse order .
b) Minimum regulation of the gas oven burner with thermostat:
• light the burner as described in the paragraph “the o v en knob” of the instruction booklet.
• turn the knob to Max for about 10 minutes and then turn the knob to the Min setting;
• remove the knob;
• regulate the screw positioned outside the thermostat pin until the flame is small but steady.
N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom.
• check that the burner does not turn off when you turn the knob from Max to Min and and when you open
and close the oven door quic kly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
• remove the screw and then slide out the grill burner “V” (see Fig. E);
• unscrew the grill burner nozzle using the special sock et spanner for the nozzles (see Fig. F) or better still
a 7 mm socket spanner; replace the nozzle with a nozzle for the new type of gas (see table 1).
V
I
Fig. E Fig. F
Important
On completion of the operation, replace the old rating sticker with one indicating the new type of gas used.
This sticker is available from our Service Centres.
Note
Should the pressure of the gas used be different (or vary) from the recommended pressure, it is necessary to
fit a suitable pressure regulator onto the inlet pipe in compliance with current National Regulations relative to
“regulators for channelled gas”.
8
Burner and Nozzle Specifications
Table 1 Liquid Gas Natural Gas
Burner Diameter
(mm)
Thermal Powe r
kW (p.c.s.*)
By-Pass
1/100
Nozzle
1/100
Flow*
g/h
Nozzle
1/100
Flow*
Nominal Reduced (mm) (mm) *** ** (mm)
Fast
(Large)(R)
Semi Fast
(Medium)(S)
Auxiliary
(Small)(A)
100 3,00 0,7 41 87 218 214 128 286
75 1,90 0,4 30 70 138 136 104 181
51 1,00 0,4 30 52 73 71 76 95
Oven - 2,60 0,6 36 75 189 186 123 248
Grill - 2,50 1,3 63 80 182 179 122 238
Supply
Pressure s
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
* At 15°C and 1013 mbar- dry gas
** Propane P.C.S. = 50,37 MJ/Kg
*** Butane P.C.S. = 49,47 MJ/Kg
Natural P.C.S . = 37,78 MJ/m
3
l/h
KD3G2/G
KD3G21/G
S
S
R
A
9
Safety Information
When used properly your appliance is completely safe but as with any electrical product there are certain
precautions that must be observed.
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE.
Always
l Remove all packing from inside the oven and grill compartments before switching on for the first time.
l Understand the controls prior to using the appliance.
l Keep children away from the appliance when grilling as the surfaces will get extremely hot during and after use.
l Turn controls off when you have finished cooking and when not in use.
l Stand back when opening an oven door to allow any build up of steam or heat to disperse.
l Use dry good quality oven gloves when removing items from the oven/grill.
l Place pans centrally over the hotplate making sure handles are kept away from the edge of the hob and cannot
become heated by other hotplate/pans.
l Take care to avoid heat/steam burns when operating the controls.
l Turn off the electricity supply at the wall switch before cleaning and allow the appliance to cool.
l Make sure the shelves are in the correct position before switching on the oven.
l Keep the oven and grill doors closed when the appliance is not in use.
l Take care when removing items from the grill when the lower oven is on as the contents will be hot.
l Keep the appliance clean, as a build up of grease or fat from cooking can cause a fire.
l Follow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.
l Keep ventilation slots clear of obstructions.
l Refer servicing to a qualified appliance service engineer.
l Take care to avoid touching heating elements inside the oven, as during use the oven becomes hot.
10
Safety Information
Never
l Never line the interior of the oven with foil as this may cause the appliance to overheat.
l Never leave children unsupervised where a cooking appliance is installed as all surfaces will be hot during and
after its use.
l Never allow anyone to sit or stand on any part of the appliance.
l Never store items above the appliance that children may attempt to reach.
l Never leave anything on the hob surface when unattended and not in use.
l Never remove the oven shelves whilst the oven is hot.
l Never heat up unopened food containers as pressure can build up causing the container to burst.
l Never store chemicals/food stuffs, pressurised container in or on the appliance, or in cabinets immediately
above or next to the appliance.
l Never place flammable or plastic items on or near the hob.
l Never fill a deep fat frying pan more than 1/3 full of oil, or use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
l Never operate the grill with the grill door closed as this will cause the appliance to overheat.
l Never use the appliance as a room heater.
l Never use the grill to warm plates.
l Never dry any items on either the hob or oven doors.
l Never install the appliance next to curtains or other soft furnishings.
l Never use steam cleaners.
SAFETY ADVICE IN CASE OF A CHIP-PAN FIRE
In the event of a chip pan fire or any other pan fire.
1. TURN OFF THE COOKER APPLIANCE AT THE WALL SWITCH.
2. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will smother the flames and extinguish the
fire.
3. LEAVE THE PAN TO COOL FOR AT LEAST 60 MINUTES BEFORE MOVING IT. Injuries are often caused by
picking up a hot pan and rushing outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force
of the extinguisher is likely to tip the pan over.
Never use water to extinguish oil or fat fires.
11
Features
HOB VENTILATION SLOTS
GRILL/MEAT PAN
WITH REMOVABLE
HANDLE AND WIRE
FOOD SUPPORT
GRILL DOOR
REMOVABLE
INNER GLASS
DOOR
1900W
GRILL
1000W
1900W
3000W
CONTROL
PANEL
MAIN OVEN
WIREWORK
SHELF
SUPPORTS
MODEL & SERIAL
NUMBER
OVEN ROD
SHELVES
12
Control Panel
TIMER*
ELECTRONIC*
INIECTION
BUTTON
Control Knobs
for the gas
burners
Electronic
Ignition
for the Gas Hob*
Timer *
MAIN
GRILL
OVEN
The position of the gas burner controlled by each one of the knobs is shown by a solid ring •. To
light one of the burners, hold a lighted match or lighter near the burner and, at the same time,
press down and turn the corresponding knob counter clockwise to the maximum E setting. Each
burner can be operated at its maximum, minimum or intermediate power. Shown on the knob are
the different symbols for off • (the knob is on this setting when the symbol corresponds with the
reference mark on the control panel), for maximum E and minimum C. To obtain these settings,
turn the knob counter clockwise with respect to the off position. To turn off the burner, turn the
knob clockwise until it stops (corresponding again with the • symbol).
This device operates when a slight pressure is applied to the button marked with symbol. To
light a specific burner just press the button
and turning it counter-clockwise until it lights. For immediate lighting, first press the button and
then turn the knob.
Important: Should the burner flames accidentally go out, turn off the control knob and wait
at least 1 minute before trying to relight.
To use the timer, the buzzer must be wound up by turning the knob one full turn clockwise; then
turn it back to the desired time so that the number of minutes on the knob matches the reference
mark on the panel.
LEFT
FRONT
BURNER
LEFT
REAR
BURNER
while pushing the corresponding knob all the way in
RIGHT
REAR
BURNER
RIGHT
FRONT
BURNER
* (only available on certain models)
13
Use of Hotplates
Practical Advice on Using the Burners
To use the burners as efficiently as possible, some basic guidelines should be follo wed:
• Use cookware that is the right size for each burner (see table) in order to prevent the flame from spreading
beyond the bottom of the cookware.
• Only use cookware with flat bottoms.
• As soon as the boiling point is reached, turn the knob to the lowest setting.
• Always use lids with pots and pans.
Burner ø Cookware diameter (cm)
Fast (R) 24 - 26
Semi Fast (S) 16 - 20
Auxiliary (A) 10 - 14
N.B.: On models equipped with a reduction grid, the grid should only be used with the auxiliary burner when
cookware with a diameter of less than 12 cm is used.
1. Press the ignition button and then push in and turn the control knob of the chosen burner anti-clockwise
to the large flame symbol. Continue to press the ignition button until the sparks light the gas.
2. Turn the control knob anti-clockwise to the desired setting. Only turn the control knob between the large
flame symbol and the small flame symbol for adjusting the setting.
3. To turn off, turn the control knob fully clockwise to the symbol O.
DO NOT use the hotplate unless all pan supports are in position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
DO NOT use the glass lid (if fitted) as a working surface.
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of the burners every time they
are used, the ignitors must be kept clean and dry. Remove any food spillage or cleaning materials from the
electrode using a small nylon brush such as a tooth brush. Access to the electrode can be achieved by lifting off the
loose burner parts carefully when the burners are cool.
When the hotplate burner bodies and caps are removed for cleaning, be careful not to drop any food particles or
cleaning materials into the burner bases, to avoid the possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit may appear on the top edge of the pan support fingers. See
'Care and Cleaning' section for cleaning information.
SAFETY REQUIREMENTS FOR DEEP F AT FR YING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat. Frozen foods in
particular will cause frothing and spitting if added too quickly.
5. Always keep the outside of the pan clean and free from streaks of oil or fat.
HOW T O DEAL WITH A FA T FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire. Do not use water or a fire
extinguisher as the force of it may spread the burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.
14
Grilling
CAUTION: A CCESSIBLE PARTS WILL BECOME HOT WHEN THE GRILL
To operate the grill proceed as follows:
l Open the grill door and remove the grill pan.
l Press the ignition button and then push in and turn the grill control knob anti-clockwise to the large
flame symbol. Continue to press the ignition button until the spark lights the gas.
Grill Pan Handle
l T urn the control knob anti-clockwise to the desired setting. There is a delay of about six seconds
whilst the safety device operates before the burner comes on full. Only turn the control knob between
the large flame symbol and the small flame symbol when adjusting the setting.
l T o turn off, turn the control knob fully clockwise to the symbol O
Important: when using the grill, the oven door must be left open by positioning the deflector “B”
between control panel and deflector “A” to prevent the cooker knobs from overheating.
GRILLING MUST BE DONE WITH THE GRILL DOOR OPEN.
CONTROL KNOBS MAY BECOME HOT DURING GRILLING.
IS USED - CHILDREN SHOULD BE KEPT AWAY.
A
B
Slide the grill pan along the runner towards the rear of the grill compartment until it stops. An
odour may be noticed when first using the grill - this schould cease after a short period of use.
Grill can be started from cold but for the best result preheat for approximately five
minutes. Most cooking is done with the heat on full, but it may be necessary after sealing the
food to reduce the heat as required.
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska place the
dish on the floor of the grill compartment. The base of the grill pan can be used for warming
fruit garnishes on the reduced setting.
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat, intensify the heat and create a fire hazard.
Relighting‘
the burner
Fixing the Grill Pan
Handle
In the event of the burner flames being accidentally extinguished, turn off the burner control and do not
attempt to re-ignite the burner for at least one minute.
The grill pan handle is detachable from the pan, to facilitate cleaning and storage. Fix the grill pan
handle securely in position before use.
The handle fits onto the grill pan edge with the small recess, Fig.1.
Tilt the handle over the recess and slide it towards the centre, Fig.2.
Ensure the handle is fully located. Insert the washer and fixing screw and tighten fully to ensure handle
is secured, Fig.3.
Always hold the dripping pan handle in the highlighted zone marked "OK" in figure 4.
Recess
Fig. 1
Fig. 2 Fig. 3
Always fit the screw prior to use.
Fig. 4
NO
OK
The food to be cooked should be placed on the grill pan/grill pan food support.
Place the grill pan on the runners and push back to the stop position when the grill pan is
correctly positioned beneath the grill element.
Plates and dishes placed on the floor of the grill compartment will be heated when the oven is
in use.
15
Oven
The oven has different heat zones - the thermostat settings refer to the temperature on the
middle shelf; above this shelf it is hotter and below it is cooler. Two shelves enable full use of
the temperatures inside the oven.
Each shelf has a safety stop to prevent if from being pulled out too far when attending to
food. Shelves are removed from the oven by pulling them out to the stop and then lifting
them at the front to withdraw.
The grill pan without the handle can be used in the oven. The maximum size of baking tray
that should be used is 300mm x 330mm (12" x 13").
TO USE THE OVEN 1. Place oven shelves in the chosen positions (refer to cooking charts).
2. Press the ignition button and then push in and turn the oven control knob fully anti-clockwise.
Continue to press the ignition button until the spark lights the gas.
3. Turn the control knob clockwise to the required setting (refer to cooking chart). There is a
delay of about six seconds whilst the safety device operates before the burner comes on full.
4. To turn off, turn the control knob fully clockwise the the symbol 0.
Never place dishes on the oven base over the burner.
An odour may be noticed when first using the oven - this should cease after a short period of
use.
5. The oven temperature control marking are gas marked 0 to 9.
The equivalent degrees Celsius (sometimes called Centigrade) and degrees Fahrenheit
are shown below as a guide.
MAIN OVEN
Gas Mark
1 120 250
2 150 300
3 175 350
4 195 385
(Centre Oven Temperature)
Celisus
°C
Fahrenheit °F
Gas Mark
5 210 410
6 220 430
7 230 445
8 235 455
9 240 465
MAIN OVEN
(Centre Oven Temperature)
Celisus
°C
Fahrenheit °F
RELIGHTING
THE BURNER
COLD START
COOKING
RO ASTING OF
LARGE POUL TR Y
STORAGE AND
RE-HEATING
OF FOOD
‘COOK CHILL ’
DISHES
In the event of the burner flames being accidentally extinguished, turn off the burner control
and do not attempt to re-ignite the burner for at least one minute
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be put into
a cold oven. Satisfactory results can also be obtained with creamed mixture, rich pastries or
yeast mixtures, but for perfection we recommend preheating the oven for about 15 minutes.
The maximum weight of poultry that can be accommodated is 8kg (18 Ibs) of suitable shape.
It is important to check that the bird DOES NOT overhang the burner at the back of the oven.
It is vitally important to strictly adhere to the basic principles of food handling and hygiene to
prevent the possibility of bacterial growth.
1. If food is to be frozen or not served immediately, cool it in a clean container as quickly as
possible.
2. Completely thaw frozen food in the refrigerator before reheating.
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven, Mk. 6, and
then serve immediately.
4. Only re-heat food once.
These should always be placed in a pre-heated oven ideally on the first or second shelf
position. Follow the packet instructions for cooking time.
ALUMINIUM FOIL If using Aluminium Foil:
1. Remember that it is important to increase the cooking time by one third.
2. Never allow the foil to touch the sides of the oven.
3. Never cover the oven interior with foil.
4. Never cover the oven shelves with foil.
16
Oven Cooking Chart
The following times and setting are for guidance only. You may wish to alter the setting to give a result more to your
satisfaction. When a different setting to that shown below is given in a recipe, the recipe instructions should be
followed. Allow 15 minutes preheat for best results. Always turn the thermostat knob to Mark 9 before selecting the
appropriate gas Mark. Shelf position 1 is the highest.
Food Gas
Fish
Oily and white fish 3 or 4 4 25-60 mins. depending on recipe
Meat and Po ul tr y
Beef 4 or 5 4 25-30 mins per 450g (1 Ib) + 25 mins. extra
Ham 5 4
Lamb 5 4 30 mins per 450g (1 Ib) + 30 mins extra
Pork 5 4 40 mins per 450g (1 Ib) + 40 mins extra
Chicken 5 4 25 mins per 450g (1 Ib) + 25 mins extra
Duckling & Goose 5 4 25 mins per 450g (1 Ib) + 25 mins extra
Turkey 4 or 5 4 or 5 15-20 mins per 450g (1 Ib) + 20 mins
Casseroles 3 3or4 2-6 hrs. depending on cut of meat
Vegetables
Baked jacket potatoes 4 or 5 3 1½ - 3 hrs. until soft, depending on size
Puddings
Milk Puddings (500ml/1 pt) 3 4
Baked Custard (500ml/1 pt) 3 4 45-60 mins. bain-marie
Baked Sponge Puddings 4 3 40-50 mins
Baked Apples 3 3 30-45 mins depending on type and size of apples
Meringue Topped Puddings 1 3or4 15 mins or until "tinged" with brown
Apple Tart (1 x205mm/8//) 6 2 45-60 mins
Fruit Crumble 5 2 35 -45 mins
Cakes, Pastries & Biscuits
Small Cakes 2 trays 5 2 and 4 15-25 mins.
1 tray 5 2 15-22mins.
Victoria sandwich (2 x 7")
Swiss Roll (3 egg quantity) 5 2 15-20 mins.
Meringues 1 3 2-3 hrs
Christmas cake (1 x 205mm / 8") 2 3 Time depending on recipe
Madeira cake (1 x 180mm /
Rich Fruit cake (1 x 180mm /
Scones 7 1 and 3 10-20 mins.
Shortbread (1 x 180mm /
Biscuits 4 1 and 3 10-20 mins.
Shortcrust Pastry 6 2 15 - 60 mins depending on use.
Rich Short Crust 5 1 and 3 20-30 mins.
Flaky/Puff Pastry 7 2 10-30 mins.
Choux Pastry 6 2 20-30mins.
Yeast Mixtures
Bread - rolls 7 2 and 4 20-30 mins.
Miscellaneous
Yorkshire Pudding:- large 7 1 30-40 mins
individual 7 2 20-30mins
7")
7")
7")
Mark
4 2 and 4 20-30 mins
4 4 1¼-1½ hrs.
2 4 Time depending on recipe
2 3 55 -65 mins.
Shelf
Position
Approx. Cooking Time and Comments
40 mins per 450g (1 Ib) covered in foil plus 40 mins.
extra
1¾-2½ stand dish on baking tray and started with
warm milk
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray moved up to the top
position for a few minutes longer.
Soft Margarine -
Use the oven settings recommended by the margarine manufacturer and not those indicated on the cooking chart.
17
Care and Cleaning
Grill
Control Panel
Decorative T rims
Doors
Remove the grill pan and the wire grid food support, it is best to wash these items immediately
after use to prevent stains from being burnt on when used again. Wipe out the Grill compartment,
use a fine steel wool soap pad to remove stubborn stains from the grill runners and the floor of the
compartment. Wipe over the control panel with a damp cloth and polish with a dry cloth.
Do not use cream cleaners, oven cleaners or aerosols, scouring pads or abrasive powder for
cleaning the plastic knobs as damage will occur.
It is advisable to clean the decorative trims regularly to prevent any build up of soiling. The
recommended method of cleaning is to wipe over the trims with a soft cloth wrung out in warm
water or mild non-abrasive cleaner. (If in doubt try the cleaner on a small area of trim which is not
noticeable in normal use). Then, after wiping with a cloth wrung out in clear water, dry with a soft
clean cloth.
Wipe over the outer door glass panels with a cloth wrung out in warm soapy water, then after
wiping with a cloth wrung out in clear water, dry with a soft clean cloth. Ensure that glass doors
are not subjected to any sharp mechanical blows.
Glass Inner Door Panel (where fitted) – open the door fully and unscrew the two screws securing
the glass panel, taking care not to allow the glass to fall. The glass panel may now be washed at
the sink. Stubborn stains can be removed by using a fine steel wool soap pad. Ensure the glass
panel is not subjected to any sharp mechanical blows. Take particular care not to damage the
inner surface which is coated with a heat reflective layer. After cleaning, rinse and dry with a soft
cloth. For slight soiling the inner glass panel may be cleaned, while still warm, without removing it
from the door.
Warning: Oven must not be operated with inner door glass removed.
Take care during cleaning not to damage or distort the door seals. Do not lift the door seal from
the oven chassis, if necessary remove the seal by carefully unhooking the corner clips.
Take care that the rating label edges are not lifted during cleaning, and fur thermore that the
lettering is not blurred or removed.
Ovens
Oven Shelf
Supports
Oven Lamp
Replacement
Remove the rod shelves and grill pan. Use a fine steel wool soap pad to remove stubborn stains
from the rod shelves, grill pan and the floor of the oven.
The shelf supports are removable and dishwasher safe.
To remove hold the support at the front and pull away from the oven side, this can then be cleaned
in a sink or a dishwasher. When removed it allows access to the oven side, which can be cleaned
with warm soapy water.
To refit the support, insert the longer leg into the rear fixing hole and push in the front leg.
Open the oven door and remove the rod shelves. Using a suitable cloth to protect the fingers grip
the light glass dome, unscrew anti-clockwise and lift. Reach into the aperture with fingers, and
unscrew the lamp anticlockwise. Fit replacement lamp (15W 300°C rated SES), refit dome.
WARNING: To avoid electric shocks - please ensure that the electricity supply to the
appliance is switched off and the appliance is fully cold, before removing the lamp lens.
18
Cooking Results Not Satisfactory?
Problem Check
Gril lin g
Uneven cooking front to
back
Fat sp lattering Ensure that the grill is not set to too high a temperature.
Ensur e th at t h e gr ill p an is po sitione d c ent r ally b elo w t h e gr ill
element.
Oven Ba k i ng
Uneven rising of cake
Sink ing of c a kes The fo llow ing may ca us e ca k e s t o s ink :
Over/Under cooking
F as t / Slo w co ok ing
Uneven cooking of cakes 1. Too large baking sheet used. (See 'Cookery Notes')
Uneven rising of cake Ensure that the shelf is level (see above) and that the food is
Foo d is taking too long to
cook
Ensure that the oven shelves are level by using a spirit level on
th e ro d sh elf a nd a d jus t in g, us in g suitab le p ac k in g e. g. woo d,
under the feet of the appliance. This should be checked both
left to right and front to back. Ensure that the food is
positioned centrally in the oven.
1. Co o k ing a t t o o high a te mpera t ure.
2. Using normal creaming method with soft margarine.
Refer to the cooking times and temperatures given in the oven
temperature charts, however, it may be necessary to increase
or decrease temperatures by 10°C to suit personal taste.
Do no t us e utensils g r ea t er t han 2¼ ins in h e ig ht .
2. Over loading of oven and always ensure even air gaps
ar o und ba k ing tins.
positioned centrally in the oven.
Only cook one item at a time to avoid overloading the oven.
19
Something Wrong with your Cooker?
Before contacting your nearest Service Centre/Installer, check the problem guide below; there may be nothing wrong
with your cooker.
Problem
Slight odour or small amount of
smoke when using the cooker for
the first time.
Nothing Works Is the main cooker wall switch turned on?
Oven temperature seems too high or
too low.
Oven does not cook evenly. Check that the temperature and shelf position are as recommended in the temperature
Ho tplates are s low t o boil or w ill not
s immer
Marks appearing on hotplates.
Can not clean hob / hotplates.
Gr ill no t working. The grill doo r MUS T be o pen.
Gr ill k eep s tur n ing on and off. When the grill co n t r ol is o per ate d at a set t in g le ss t han maximum, t h is is nor ma l r egula t or
Condensa tion on the wall at the rea r
of the cooker.
This is normal and should cease after a short period.
There may be no electricity supply.
Check that the temperature has been set in accordance with the temperature charts. It may
be necessary to increase or decrease the recommended temperature by up to 10°C to suit
your ta ste.
charts.
Check that the containers being used in the oven allow sufficient air flow around them.
Check that the cooker is level.
Check that your pans conform to the recommendations in these instructions.
The hob surround can be cleaned with warm soapy water and a cream cleaner, such as
Cif. The sealed hotplates should be cleaned regularly, (please refer to the Care and
Cleaning section for further information. Please note that replacement hob cleaning kits are
available from our parts department, see Key Contacts, back page.
operation, not a fault.
Steam and/or condensation may appear from the vent at the rear of the appliance when
using an oven particularly for foods with a high water content e.g. frozen chips, roast
chicken etc. This is normal and any excess should be wiped off.
Steam / Condensation in the oven
after use.
Steam is a by-product of cooking any food with a high water content. To help minimise
always:
a) Try to avoid leaving food in the oven to cool after being cooked.
b) Use a covered container, wherever possible
20
If It Still Won’t Work...
Contact the Service Office (0870 6070805)
If something is still wrong with your appliance after you have been through the ‘Something Wrong’ list:
1. Switch off and unplug the appliance from the mains.
2. Call your nearest Service Office or local importer.
When you contact us we will want to know the following:
1. Your name, address and postcode.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The Model number and the Serial number of your appliance.
5. The date of purchase (please keep the receipt as evidence will be required when an engineer calls)
enter the date here:
.............................................................................
Please make sure you have all these details ready when you call.
Spare Parts
Please remember your new appliance is a complex piece of equipment.
‘DIY’ repairs or unqualified and untrained service people may put you in danger, could damage the appliance
and might mean you lose cover under the Parts Guarantee.
If you do experience a problem with the appliance don’t take risks, call in our Service Engineer. Our Par ts are
designed exclusively to fit your appliance. Do not use them for any other purpose as you may create a safety
hazard.
Disposal of your product
To minimise the risk of injury to children please dispose of your product carefully and safely. Remove all doors
and lids. Remove the mains cable (where fitted) by cutting off flush with the appliance and always ensure that
no plug is left in a condition where it could be connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the disposal of your product.
21
Technical Characteristics
Main Oven
Dimensions (HxWxD): 34x39x31 cm
V olume: 41 Litres
V oltage and Frequency
See data plate.
Burners:
Adaptable for use with all the types of gas indicated on the data plate.
This appliance conforms with the following European Economic Community directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;
- 90/396/EEC of 29/06/90 (Gas) and subsequent modifications (only for models which use gas);
- 93/68/EEC of 22/07/93 and subsequent modifications.
- 2002/96/EC
The European Directive 2002/96/EC on W aste Electrical and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of in the normal unsorted municipal w aste stream. Old
appliances must be collected separately in order to optimise the recovery and recycling of the materials they
contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol
on the product reminds you of your obligation, that when you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of
their old appliance.
Mains frequency and voltage of the elect ric sec tion and char acteri stics of the gas s ection
Model Gas section Elec tri c section
Class
KD3G2/G
KD3G21/G
(1) The values in g/ h ref er to th e cap acit ies with liquid gas (B utane , Pr opane ).
II2H3+
Rated power
kW (1)
12,90 (938 g/h - G 30)
(921 g/h - G31)
Voltage
230-240V~ 50/60 Hz
22
Notes
23
Key Contacts
Repair Service and Information Desk
UK: 0870 6070805
(Open 8am to 5.30pm Mon - Fri
9am to 5pm Sat
and 10am to 4pm Sun
Closed Bank Holidays)
Note: Our operators will require the f ollowing inf ormation:-
Model Number:
Serial Number:
Extended W arranty
To join: UK 0870 442 7661
(Open 8 to 8 Mon-Sun)
Genuine Parts & Accessories
Mail Order Hotline
To join: UK 0870 558 5850
(Open 8.30 to 5 Mon-Fri and 8.30 to 12 Sat).
All Services are offered as an extra benefit and do not affect your statutory rights.
Indesit Company UK Ltd, Morley Way, Peterborough, PE2 9JB
06/2005 - 195048072.02
Loading...