Inateck FD2002 User Manual

Instruction Manual

FD2002 USB3.0 Dual SATA HDD Docking Station

With O󱐱ine Clone Function

English · Deutsch · 日本語

English

Introduction

This product support data copy and clone between dual HDDs.
Meanwhile, it adopts USB3.0 (Super Speed) with date transfer rate up to

Meanwhile, it adopts USB3.0 (Super Speed) with data transfer rate up to
5Gbps and SATA3 (6Gbps) and backward compatible with earlier versions
as well. This excellent transmission performance and good compatibility
is convenient for data exchange and perfectly suitable for the men who
need to batch processing and clone data at some certain places, such
as lm and television production, Backup & processing IT data, Schools
batch processing data etc.

Overview

LED Indicator

SATA HDD Slot

Clone Button

DC-IN Jack

USB 3.0

Power Switch

1

How to Use

1. Connect the external power adapter from the hard drive dock to an
electrical outlet.

2. Connect the included USB 3.0 cable from the hard drive dock to an
available USB port on the computer system.

3. Insert a 2.5” or 3.5” hard drive into the top loading slot.

4. Press the power button. A pop-up bubble in the task bar at the bottom­right of your screen notifying you once your hard drive has been
recognized. You may also nd the hard drive in Disk Management.

Note:

a. To remove the hard drive, make sure it is currently not being accessed

by the computer then unmount or uninstall the disk drive from the
operating system. Never remove the docking station while the hard
drive is in use. Doing so may corrupt the data on the hard drive or
damage the hard drive, docking station, or computer.

b. When connected via USB, the dock will automatically go into sleep

mode if the connection is left idle for more than 30 minutes. The
power LED indicator will flash every 3 seconds. Accessing the hard
drive will automatically cancel sleep mode and power the drive back
up. The hard drive LED indicator will ash and the power LED indicator
will be constantly on.

c. Please do not remove your hard drive or insert a new one while

the other hard drive is being accessed, as doing so the other drive
temporarily disconnects and this could damage your hard drive and
result in data loss.

Hard Drive O󱐱ine Clone

1. Make sure there are no connection on the USB.

2. Insert the drives straight down until the connection is secured. O󱐱ine
clone is from HDD A to HDD B. Make sure your Main Drive is in HDD
A and slave in HDD B. The capacity of HDD B must be equal or bigger
than HDD A.

3. Press and hold the o󱐱ine clone button for 3 seconds, the LED indicator
will light up. Then quickly press the o󱐱ine clone button and the o󱐱ine
clone operation will start. Each LED represents 25% completion. It is
only when every 25% of HDD A is offline clone to HDD B that such
LED will remain constantly on. When offline clone operation is fully
completed, all LEDs will constant on until the device is power o󱐯.

2

Technical Specications

Product Name USB3.0 Dual SATA HDD Docking Station with O󱐱ine Clone Function

Model Number Inateck FD2002

Weight 410g

Color Black

Drive Size 2.5”/3.5” SATA I/II/III HDD/SSD

Interface USB3.0 up to 5Gbps

Material ABS plastic

Hot Plug, Plug & Play Supported

Licenses CE, FCC

Dimensions 450mm length × 109mm width × 60mm height

Environmental Storage: -20 to 70 ° C; Operating: 5 to 40 ° C

Operating Systems Windows XP/7/8/8.1/10, Mac OS 9.0 and higher

Tool free Yes

Driver No software or drivers required

Package Contents

FD2002 Docking Station × 1
USB 3.0 Data Cable × 1
DC Power Adapter × 1
Instruction Manual × 1

Troubleshooting/FAQ

a. Unable to clone: Please check if the capacity of Disk B is larger or

equivalent to that of Disk A. Here the capacity means the actual
capacity that can be used, instead of the one marked on the product.
For example, the actual capacity of a disk marked 500GB might be
480GB only. The actual capacity of disks with the same marked capacity
differs if they are produced by different producers. To ensure two
disks of the same marked capacity have the same actual capacity, they
should be produced by the same producer in the same batch with the
same model number.

3

b. Indicator light stops ashing up during o󱐱ine duplicating: it might

because of disk bad sectors so that data couldn’t be cloned as usual.
It’s better to change a good disk.

c. After cloning, the rest capacity of B disk is showed and operated via

“Computer management - Storage - Disk management”.

d. Why over 2TB hard disk couldn’t be identied by USB? Because the

maximum capacity of hard disk which Windows XP can supports is 2TB
and couldn’t be identied by system if over 2TB. It only supports after
upgrading the operating system above Vista (64 bit) version and we
suggest changing hard disk into a GPT disk partition, or the operating
system will not support over 2 TB disk partitions.

e. Please make sure that B hard disk data can be covered before cloning

data. Because once you start cloning, B hard disk partition methods
and data are completely cloned as A hard disk. Our company does NOT
undertake any responsibility for data or economy loss which could
bring by damaged data.

f. Please do not remove your hard drive or insert a new one while

the other hard drive is being accessed, as doing so the other drive
temporarily disconnects and this could damage your hard drive and
result in data loss.

Support

For any inquiries or comments concerning our products, please send an
email to [e-mail], and we will respond to you as soon as
possible.

4