Inateck BR1005 Instruction Manual

Instruction Manual

English · Deutsch · 日本語

BR1005 Bluetooth Adapter

1

English

Overview

A

B

C

D

E

F

G

H

No. Name

A Multifunction Button

B TX/RX Switch (TX mode: transmitter; RX mode: receiver)

C SPDIF / AUX Mode Switch ( SPDIF: optical audio; AUX:3.5mm audio)

D 3.5mm Audio Port (AUX)

E Optical Audio Input Port(SPDIF IN)

F Optical Audio Output Port (SPDIF OUT)

G USB Charging Port

H LED Indicator

2

Charging

The LED indicator will flash red if the battery level is low, which
indicates charging is necessary.

1. Plug the USB end of the charging cable to a USB charging port or
any active USB port (charging power: DC 5V).Connect the Micro
USB end of the charging cable to the charging port of the BR1005.

2. The LED indicator will turn red when charging.

3. The LED indicator will automatically turn off when the device is
fully charged. It takes up to 2.5 hours to fully charge the Bluetooth
adapter.

Note:

a. Poor quality power adapters do not provide a stable current ,

which may generate current noises when using.

b. To avoid battery over-discharge, please recharge the device once

a month if the device is not in regular use. Lithium-Ion batteries
continue to slowly discharge (self-discharge) when not in use or
while in storage.

Common Functions

1. Power On/O󱐯
Press and hold the Multifunction Button for 3 seconds.
Power on: the LED indicator will blink blue.
Power o󱐯: the LED indicator will blink red and automatically turn o󱐯.

2. Automatically Pairing with Previously Paired Devices
BR1005 will enter pairing mode automatically when powered on for

the rst time. BR1005 can remember previously paired devices and
will attempt to pair with devices automatically, without going into
pairing mode.

3. Quickly Enter Pairing Mode
Quickly double-click the Multifunction Button to enter pairing

mode after the BR1005 is powered on.

4. TX/RX Mode Switch
TX/RX mode can only be successfully switched after the adapter is

turned o󱐯 for 5 seconds.
Note: turn o󱐯 the BR1005 and restart it after 5 seconds if the mode

switch is not functioning properly.

3

5. Clear Pairing History
Please follow the guides below to clear the pairing history if pairing

failures are encountered:

1) Turn o󱐯 the BR1005, switch TX (RX) mode to RX (TX) mode after 5

seconds, and then restart the BR1005.

2) Turn o󱐯 the BR1005, switch RX (TX) mode to TX (RX) mode after

5 seconds. After that, the pairing history of TX (RX) mode will be
cleared.

6. AUX and SPDIF Mode Switch
You can freely switch between SPDIF and AUX mode. In SPDIF

mode, connect devices through SPDIF IN for TX mode and SPDIF
OUT for RX mode.

7. RX Mode: Pause/Play
Press the Multifunction Button to pause or play while playing music.

8. Auto-o󱐯
In RX mode, the BR1005 will automatically power o󱐯 if there is no

device to be connected within 6 minutes. The BR1005 will not turn
o󱐯 automatically in TX mode.

Bluetooth Transmitter Mode (TX)

The transmitter mode enables the BR1005 to transmit audio signal
from non-Bluetooth devices like TV or computer to headphones or
speakers. When BR1005 is in TX mode, you can connect BR1005 with
a non-Bluetooth audio device like a TV / computer via an AUX audio
cable or optical audio cable. Then connect the BR1005 with Bluetooth
headset / speakers etc. via Bluetooth.

4

LED Indicator

How to Use

1. Pairing

1) Set your Bluetooth enabled devices like Bluetooth headphones or
speakers to pairing mode.

2) Set the BR1005 to TX mode. Then press and hold the Multifunction
Button for 3 seconds to turn it on. Tap the Multifunction Button
twice to enter pairing mode with the LED indicator keeps rapidly
flashing blue. The BR1005 will automatically exit pairing mode if
there is no device to be connected within 2 minutes.

3) Place your Bluetooth audio receiving devices like earphones or
speakers closely to the BR1005. After approximately 30 seconds,
pairing will be completed. The BR1005 LED indicator will turn solid
blue.

4) Switch between AUX and SPDIF mode. Connect the BR1005 to
your audio output devices like TV through a 3.5mm audio cable or
optical digital cable.

Note:

a. BR1005 will enter pairing mode automatically when powered on for

the rst time.

b. BR1005 can only automatically re-pair to the 4 most recently

connected devices.

2. Pair with two devices at the same time
In TX mode, BR1005 is able to pair with two Bluetooth stereo

earphones / speakers at the same time. And both can play music at
the same time.

1) Follow the previous instructions in the “Pairing” section to pair
the BR1005 with your first device. Turn off your first device after
successfully pairing it with the BR1005.

2) Tap the Multifunction Button twice to pair and connect to your
second device. Turn o󱐯 the BR1005 after successfully pairing it with
your second device.

LED Indicator (TX Mode) Status

Rapidly Flashing blue In pairing mode

Blue LED ashes twice every 3 seconds Automatically Pairing with Previously Paired Devices

Solid blue Successfully paired

5

3) Turn on your rst device and wait for 10 to 20 seconds. Both of your
devices are now ready for pairing. Turn on the BR1005, the devices
will automatically connect in.

Note:

a. Please turn off the BR1005 and restart it to re-pair if two devices

cannot play music at the same time. If the problem still exists after
repeating the whole steps above, please contact Inateck Support
at: [e-mail].

b. It is advised to switch off the Bluetooth function of your other

devices to avoid signal interference.

c. We have performed the compatibility testing with various Bluetooth

chipsets on the market. But please note not all these chipsets use
the same software, compatibility issue might still encounter for
some Bluetooth devices. Please contact our customer support team
for help.

d. BR1005 can automatically re-pair to the 2 most recently connected

devices.

Bluetooth Receiver Mode (RX)

When BR1005 is in RX mode, you can connect BR1005 with a non­Bluetooth audio device like a headphone/ speaker/ audio amplifier
via an AUX audio cable or optical audio cable. Then connect BR1005
with Bluetooth enabled devices like smartphones or laptops etc. via
Bluetooth. Therefore, non-Bluetooth audio device like a headphone/
speaker can receive audio signals via Bluetooth.

6

LED Indicator(RX Mode) Status

Blue and red LED ash alternately In pairing mode

Blue LED ashes twice every 3 seconds Automatically Pairing with Previously Paired Devices

Solid blue Successfully paired

LED Indicator

How to Use

1. Pairing

1) Set the BR1005 to RX mode before turning it on.

2) Turn on the BR1005 by pressing and holding the Multifunction
Button for 3 seconds. Rapidly tap the Multifunction Button twice
to enter pairing mode with the LED indicator ashes blue and red
alternately.

3) Activate the Bluetooth function on your transmitting device and
find "Inateck BR1005" to connect. The BR1005 LED indicator will
turn solid blue after successfully paired.

4) Connect the BR1005 to your headphone or home stereo playback
device through a 3.5mm audio or SPDIF OUT port to enjoy the
music.

Note:

a. If a PIN code is required for pairing, try 0000, 8888, 1111 or 1234.
b. This product has no built-in microphone which cannot be used for

hands-free calls.
c. BR1005 can remember 8 paired devices, when the number of paired

devices exceeds 8, the rst one will be replaced.

2. Pair with two devices at the same time

In RX mode, BR1005 is able to pair with two Bluetooth enabled
smartphones/tablets at the same time. Only one device can play
music at any time. You have to stop the music on one device to play
on the other. Please follow the instructions below:

1) Follow the previous instructions in the “Pairing” section to pair the
BR1005 with your first device. Disable the Bluetooth function on
your rst device after successfully pairing BR1005 with it.

2) Rapidly tap the BR1005 Multifunction Button twice to pair and
connect to your second device

7

3) Turn o󱐯 the BR1005 after successfully pairing it with your second
device. Activate the Bluetooth function on your rst device, turn on
the BR1005 after about 20 seconds. After approximately 30 seconds,
pairing will be completed.

Product Specications

Package Contents

BR1005 × 1

3.5mm Audio Cable × 1

Optical Digital Cable × 1

3.5mm Female to RCA Male Cable × 1

Micro-B Charging Cable × 1
User Manual × 1

Bluetooth Version V4.1, Class Ⅱ

Bluetooth Chipset CSR BC8670

Working Time (AUX) Approx. 20 hours

Working Time (SPDIF) Approx. 16 hours

Charging Time 2.5hours

Bluetooth Prole RX: A2DP AVRCP

TX: A2DP

CODEC TX: aptX Low latency, aptX, SBC, FastStream

RX: SBC

Battery Capacity 450mAh lithium-ion polymer battery

Charging Power DC5V

Charging Current ≥300mA

Operating Temperature -10 - 55℃

Weight Approx. 40.6g

Dimensions 60*60*18.4mm

8

FAQ

1. BR1005 will not automatically re-pair to my devices after turning on
it. I am having trouble pairing and connecting to my devices after
turning on it.

Follow the previous instructions in the “Clear Pairing History”
section to clean the pairing list and reconnect.

2. BR1005 will not power on.
Plug BR1005 into a charger and see if the LED indicator turns red.

Please recharge it until the LED indicator turns o󱐯 to make sure the
adapter has enough battery power. Please contact our customer
support team if you need further assistance.

3. After connecting with my Bluetooth device, I cannot hear any music
from my sound system.

Please check the following:

•Your sound system is connected to the adapter via the audio cable
or optical digital cable.

•Make sure the audio port of the BR1005 and the audio output
setting on your TV are matching. In TX mode, the audio output
mode on your TV would be digital audio if it is connected to the
BR1005 through the SPDIF port.

• Make sure the music volume is at an audible level on both your
Bluetooth device and sound system.

• For some systems, you may need to select “AUX” or “Line-in” as
the audio input mode.

• Some devices (such as computer) require manually selecting the
music output mode.

Support

If you need any further assistance regarding the Inateck BR1005
wireless adapter, please contact our customer support team at
[e-mail].