Impex SM-1050 Owner's Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

MARCY DIAMOND ELITE

SMITH MACHINE

SM-1050

Model

SM-1050

Retain This

Manual for

Reference

100624

OWNER'S
MANUAL

IMPEX® INC.

2801 S. Towne Ave., Pomona, CA 91766

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

SMITH MACHINE HARDWARE PACK……….....….......................................... 4

SMITH MACHINE ASSEMBLY INSTRUCTIONS...............................................6

SMITH MACHINE EXPLODED DIAGRAM........................................................10

SMITH MACHINE PARTS LIST…………………………………………………… 11

BENCH HARDWARE PACK……….....…..................................................…….12

BENCH ASSEMBLY INSTRUCTIONS......................................................…….14

BENCH EXPLODED DIAGRAM...............................................................……..18

BENCH PARTS LIST…………………………………………………………………19

WARRANTY.................................................................................................…. 20

ORDERING PARTS.......................................................................................… 20

BEFORE YOU BEGIN

Thank you for selecting the MARCY SMITH MACHINE SM-1050 by
IMPEX
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.

®

INC. For your safety and benefit, read this manual carefully before

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

CARE AND MAINTENANCE

1. Lubricate moving parts and Guide Rods with WD-40 or light oil periodically.

2. Inspect and tighten all parts before using the machine.

3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.

4. Maximum user’s weight: 300 lbs.

5. Maximum weight on Leg Developer: 100 lbs.

6. Maximum weight on Weight Bar: 300lbs.

7. Maximum weight Capacity on Bench: 600 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL PLACEMENT

The warning label shown here has been placed on the back of Rear Support. If the label is missing or
illegible, please call customer service at 1-800-888-8899 for replacements. Apply the label in the location
shown.

3

SMITH MACHINE HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

4

SMITH MACHINE ASSEMBLY INSTRUCTION

Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine
to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Note: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Attach a Base Frame (#6) to the Left Rear Support (#4). Secure it with two M10 x ¾”

Allen Bolts (#31) and two Ø ¾” Washers (#38). Repeat the same step to install the
other Base Frame to the Right Rear Support (#5).

C.) Connect the Left and Right Rear Support with the Cross Brace (#3). Secure each end

of the Cross Brace to each Rear Support with two M10 x 3 1/8” Carriage Bolts (#30),
one 5 1/8” x 1 5/8” Bracket (#17), two Ø ¾” Washers (#38), and two M10 Aircraft Nuts
(#37).

DIAGRAM 1

5

STEP 2 (See Diagram 2)

A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Left Upright Beam (#1) to the Left Rear Support (#4) and the left Base

Frame (#6).

C.) Secure it to the Base Frame with two M10 x 3 ½” Allen Bolts (#34), four Ø ¾”

Washers (#38), and two M10 Aircraft Nuts (#37).

D.) Secure it to the Left Rear Support with one M10 x 3 1/8” Carriage Bolt (#30), one

Ø ¾” Washer (#38), and one M10 Aircraft Nut (#37) from the side. Secure with
one M10 x 2 1/8” Carriage Bolt (#28), one Ø ¾” Washer (#38), and one M10

Aircraft Nut (#37) from the top.
E.) Repeat A to D to install the Right Upright Beam (#2).
F.) Slide Lower Safety Stop Frame (#13) onto a Guide Rod (#7). Slide one Safety

Stop Frame (#12) onto the Guide Rod. Insert the bottom of the Guide Rod into the

hole on the Left Rear Support. Secure it with one M10 x 3” Allen Bolt (#33), two Ø

¾” Washers (#38), and one M10 Aircraft Nut (#37).
G.) Attach the top of the Guide Rod to the bracket on Left Upright Beam. Secure it

with one M10 x ¾” (#31) and one Ø ¾” Washer (#38).
H.) Repeat F to G to install the Lower Safety Stop Frame, the Safety Stop Frame, and

the other Guide Rod to the other side.

6

DIAGRAM 2