Impex MWM 800 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

MARCY HOME GYM

MWM 800

Model

MWM 800

Retain This

Manual for

Reference

08-20-02

OWNER'S
MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE IDENTIFIER.....….....................................................................……….. 3

ASSEMBLY INSTRUCTIONS.........................................................................……….. 8

EXPLODED DIAGRAM......................................................................................……… 19

PARTS LIST………………………………………………………………………………….. 20

RESISTANCE CHART………….......................................................................………. 21

WARRANTY.................................................................................................…………. 22

ORDERING PARTS.......................................................................................………… 22

BEFORE YOU BEGIN

Thank you for selecting the MARCY MWM800 HOME GYM by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave

children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to properly
warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

Hardware Identifier

3
4

5
6

7

ASSEMBLY INSTRUCTION

Tools Required to Assemble the Machine: Two Adjustable Wrenches, two Allen
Wrenches, and one Flat Head Screwdriver
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Connect the Main Base Frame (#2) and Front Base (#3) to the Front Stabilizer (#5).

Align the holes then secure them with two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8”
Washers (#77), and 3/8” Aircraft Nuts (#74).

B.) Attach the Rear Stabilizer (#1) to the Main Base Frame. Secure it with one Bracket

(#26), two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts
(#74).

C.) Attach the Vertical Beam (#4) to the Main Base Frame (#2). Secure it with two 3/8” x 3”

Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74).

D.) Over the two holes on the Rear Stabilizer (#1), stack up two Round Rubber Bumpers

(#40), two Guide Rod Sleeves (#7), then two Round Rubber Bumpers (#40) in
sequence. Align the holes then insert two Guide Rods (#13) all the way down into the
Rear Stabilizer (#1).

E.) Slide the Weight Holder (#8) from the top onto the two Guide Rods.
F.) Place the Upper Frame (#6) onto the Vertical Beam (#4) and the two Guide Rods (#13).

Secure the Upper Frame to the Guide Rods with two 3/8” x 1” Allen Bolts (#63) and ∅
3/8” Washers (#77). Secure the Upper Frame to the Vertical Beam (#4) with two 3/8” x
3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74).

G.) Attach the Olympic Sleeves (#44) to the Weight Holder (#8). Attach the ∅ 2” Spring

Clips (#48) onto the Olympic Sleeves. Please note that we also provided two ∅1”
Spring Clips in case the ∅1” standard plates were used.

H.) Carefully tip over the machine to its side. Secure the bottom of the two Guide Rods to

the Rear Stabilizer (#1) with two 3/8” x 1” Allen Bolts (#63) and ∅ 3/8” Washers (#77).

8

DIAGRAM 1

9

STEP 2 (See Diagram 2)

A.) Attach the Seat Support (#15) to the Vertical Beam (#4). Secure it with one Bracket

(#26), two 3/8” x 3 7/8” Carriage Bolts (#68), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts
(#74).

B.) Attach the Seat post (#14) to the Seat Support (#15). Secure it with one Bracket (#26),

two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74).

C.) Secure the bottom of the Seat Post (#14) to the Front Base (#3) with one 3/8” x 4 ½”

Carriage Bolt (#67), ∅3/8” Washer (#77) and 3/8” Aircraft Nut (#74).

D.) Insert the Seat Incline Adjustment (#16) into the hole on top of the Seat Post (#14).

Secure it with a quick Release Lock Pin (#45).

E.) Place the Seat Pad (#20) onto the Seat Incline Adjustment (#16). Secure it with two M8 x

1 ½” Allen Bolts (#65) and ∅ ¼” Washers (#76).

F.) Attach a Square Rubber Bumper (#29) onto the front opening on the Seat Support (#15).

Secure it with one M10 x 1” Philips Screw (#70).

G.) Attach the Leg Developer (#17) to the Seat Support (#15). Secure it with one 3/8” x 3”

Allen Bolt (#59), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).

H.) Insert the Foam Roll Tubes (#27) halfway through the hole on the Seat Incline

Adjustment (#16) and Leg Developer (#17). Push four Foam Rolls (#43) onto the Tubes.

10

DIAGRAM 2

11

STEP 3 (See Diagram 3)

A.) Attach the Front Press Lock Pin (#22) to the Vertical Beam (#4). Secure it with one M8 x 2 ½”

Allen Bolt (#64), two ∅ ¼” Washers (#76), and one M8 Aircraft Nut (#73). Plug a 1 ½” Square
End Cap (#35) to the front opening on the Vertical Beam.

B.) Plug two ½” Metal Bushings (#72) onto the side-holes on the Upper Frame (#6). Attach the

Front Press Base (#9) to the Bushings. Secure it with one ½” x 6 1/8” Allen Bolt (#56), two ∅
½” Washers (#78), and one ½” Aircraft Nut (#75). Flip down the Lock Pin (#22) to lock the
Front Press Base for Butterfly exercise only. Flip up the Lock Pin for Front Press exercises.

C.) Plug two ½” Metal Bushings (#72) to the pivot on the Butterfly Bracket (#10). Attach the

Butterfly Bracket to the Front Press Base. Secure it with one ½” x 4 1/8” (#57) Allen Bolt (#57),
two ∅ ½” Washers (#78), and one ½” Aircraft Nut (#75). Repeat the same procedure to install
the other side.

D.) Secure the Backrest Board (#21) to the Vertical Beam (#4) with four M8 x 2 ½” Allen Bolts

(#66) and ∅1/4” Washers (#76).

12

STEP 4 (See Diagram 4)

A.) Plug two ½” Metal Bushings (#72) to the pivot on the Left Butterfly (#12). Attach the Left

Butterfly to the Front Press Base (#9). Secure it with one ½” x 3 1/8” Allen Bolt (#58), two ∅ ½”

Washers (#78), and one ½” Aircraft Nut (#75).
B.) Slide two Foam Grips (#42) onto the Left Butterfly handle.
C.) Repeat Procedures A & B above to install the Right Butterfly (#11).

DIAGRAM 4

13

CABLE LOOP DIAGRAM

14

STEP 5 (See Diagram 5 & Cable Loop Diagram)

A.) Attach the 137” Upper Cable (#52) to the open bracket on the front of the Upper

Frame (#6). Note: The Ball Stopper on the cable should be underneath the Frame.

B.) Attach a Pulley (#28) to the bracket and secure it with one 3/8” x 1 ¾” Allen Bolt

(#61), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).

C.) Draw the Cable to the open slot on the Vertical Beam (#4). Install a Pulley to the

opening. Align the holes and secure it with one 3/8” x 2 5/8” Allen Bolt (#60), two ∅
½” Bushings (#71), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).

D.) Draw the Cable over the Pulley then downward. Install a Pulley to the Flat Double

Floating Pulley Bracket (#23). Let the Bracket hanging for now. Draw the Cable
around the Pulley then upward to the open bracket on the rear of Upper Frame.

E.) Install another Pulley then pull the Cable downward to the Weight Holder (#8).

Connect the Cable to the Weight Holder with a Hook (#46).

F.) Slide two Handle Grips (#39) onto the Lat Bar (#18). Connect the Lat Bar to the

Upper Cable with two Hooks (#46) and one 12-linked Chain (#50).

15

STEP 6 (See Diagram 6 & Cable Loop Diagram)

A.) Attach one end of the 47” Butterfly Cable (#54) to the left Butterfly Bracket (#10). Secure the

Cable to the Bracket with one 3/8” x 1 3/16” Allen Bolt (#62), ∅ 3/8” Washer (#77), and 3/8”

Aircraft Nut (#74).
B.) Attach a Swivel Pulley Bracket to the Pivot on the Vertical Beam (#4). Secure it with one 3/8”

x 2 5/8” Allen Bolt (#60), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74). Draw

the Cable to the Swivel Pulley Bracket.
C.) Attach a Pulley to the Bracket. Secure it with one 3/8” x 1 ¾” Allen Bolt (#61), two ∅ 3/8”

Washers (#77), and one 3/8” Aircraft Nut (#74).
D.) Draw the Cable over the Pulley then downward. Attach an Angled Double Floating Bracket

(#24). Installed a Pulley as described in Step C. Let the Bracket hanging for now.
E.) Draw the Cable around the Pulley then pull upward. Repeat the steps above to install the

other side.

DIAGRAM 6

16

STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 133” Lower Cable (#53) to the opening on the Leg Developer (#17). Attach a Pulley

(#28) to the opening. Secure it with one 3/8” x 2 5/8” Allen Bolt (#60), two ∅ ½” Bushings

(#71), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
B.) Draw the Cable underneath the Pulley to the open slot on the Vertical Beam (#4). Install

another Pulley as described in Step A.
C.) Draw the Cable underneath the Pulley then upward to the Angled Double Floating Bracket

(#24) previously installed. Attach a Pulley to the open bracket. Secure it with one 3/8” x 1 ¾”

Allen Bolt (#61), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74).
D.) Draw the Cable around the Pulley the downward to the open bracket on the Main Base Frame

(#2). Install another Pulley.
E.) Draw the Cable around the Pulley then upward to the Flat Double Floating Pulley Bracket

(#23) previously installed. Install another Pulley.
F.) Draw the Cable around the Pulley then connect the Cable to the Main Base Frame with two

Hooks (#46) and a 9-linked Chain (#49).
G.) Adjust the tension of the Cable Loop System by adjusting the length of the Chain.

17

DIAGRAM 7

18

19

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Rear Stabilizer 1
2 Main Base Frame 1
3 Front Base 1
4 Vertical Beam 1
5 Front Stabilizer 1
6 Upper Frame 1
7 Guide Rod Sleeve 2
8 Weight Holder 1
9 Front Press Base 1
10 Butterfly Bracket 2
11 Right Butterfly 1
12 Left Butterfly 1
13 Guide Rod 2
14 Seat Post 1
15 Seat Support 1
16 Seat Incline Adjustment 1
17 Leg Developer 1
18 Lat Bar 1
19 Arm Curl Handle 1
20 Seat Pad 1
21 Backrest Board 1
22 Front Press Lock Pin 1
23 Flat Double Floating Pulley Bracket 1
24 Angled Double Floating Bracket 1
25 Swivel Pulley Bracket 2
26 Bracket 3
27 Foam Roll Tube 2
28 Pulley 12
29 Square Rubber Bumper 1
30 ∅ 1” Round End Cap 6
31 ∅ 1 3/8” Round End Cap 4
32 2” Square End Cap 7
33 1 ¾” Square End Cap 1
34 1” x 2” End Cap 4
35 1 ½” Square End Cap 1
36 2” Front Stabilizer End Cap 2
37 2” Oblique End Cap 2
38 ∅ 2” Nylon Sleeve 4
39 Handle Grip 5
40 Round Rubber Bumper 4
41 Manual 1
42 Foam Grip 4
43 Foam Roll 4
44 Olympic Sleeve 2
45 Quick Release Lock Pin 1
46 Hook 7
47 ∅ 1” Spring Clip 2
48 ∅ 2” Spring Clip 2
49 9-linked Chain 1
50 12-linked Chain 1

51 19-linked Chain 1
52 137” Upper Cable 1
53 133” Lower Cable 1
54 47” Butterfly Cable 1
55 Ankle Strap 1
56 ½” x 6 1/8” Allen Bolt 1
57 ½” x 4 1/8” Allen Bolt 2
58 ½” x 3 1/8” Allen Bolt 2
59 3/8” x 3” Allen Bolt 1
60 3/8” x 2 5/8” Allen Bolt 5
61 3/8” x 1 ¾” Allen Bolt 9
62 3/8” x 1 3/16” Allen Bolt 2
63 3/8” x 1” Allen Bolt 4
64 M8 x 2 ½” Allen Bolt 1
65 M8 x 1 ½” Allen Bolt 2
66 M8 x 5/8” Allen Bolt 4
67 3/8” x 4 ½” Carriage Bolt 1
68 3/8” x 3 7/8” Carriage Bolt 2
69 3/8” x 3” Carriage Bolt 10
70 M10 x 1” Philips Screw 1
71 ∅ ½” Bushing 6
72 ½” Metal Bushing 10
73 M8 Aircraft Nut 1
74 3/8” Aircraft Nut 30
75 ½” Aircraft Nut 5
76 ∅ ¼” Washer 8
77 ∅ 3/8” Washer 51
78 ∅ ½” Washer 10

20

21

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this pr oduct to be f ree fr om def ects in workm ans hip and m aterial,
under normal use and service c onditions , f or a per iod of two years on the Fr ame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for produc ts
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or cons equential damages aris ing out of or
in connection with the use or performance of the pr oduct or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, cos ts of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of inc idental or consequential damages. Accordingly, the above
limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is lim ited in its sc ope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state
to state.

ORDERING REPLACEMENT PARTS
Replacement parts can be order ed by calling our Custom er Ser vice Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

Register on-line at www.impex- fitness .com

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

22