Impex MWM7150 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

MARCY HOME GYM

MWM-7150

Model

MWM-7150

Retain This

Manual for

Reference

08-20-08

OWNER'S
MANUAL

IMPEX® INC.

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE PACK.....….....................................................................………………... 4

ASSEMBLY INSTRUCTIONS.........................................................................……….. 7

PARTS LIST…………………………………………………………………………………..18
WEIGHT RESISTANCE CHART……………………………………………………………19

WARRANTY.................................................................................................…………. 20

ORDERING PARTS.......................................................................................…………20

BEFORE YOU BEGIN

Thank you for selecting the MARCY MWM-7150 HOME GYM by IMPEX
INC. For your safety and benefit, read this manual carefully before using the
machine. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct
assistance from our factory. To avoid unnecessary delays, please call our
TOO-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.

®

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

CARE AND MAINTENANCE

1. Lubricate moving parts with WD-40 or light oil periodically.

2. Inspect and tighten all parts before using the machine.

3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.

4. Maximum user’s weight: 300 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL REPLACEMENT

The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels
in the location shown.

3

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

4

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

5

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

6

ASSEMBLY INSTRUCTION

Tools Required for Assembling the Machine: Two Adjustable Wrenches and
Allen Wrenches. NOTE: It is strongly recommended that two or more people
assemble this machine to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Do not tighten the nuts and bolts until instructed to do so.
B.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#33) onto the Guide Rods (#10). Insert

the two Guide Rods into the holes on the Rear Base Frame (#5). Secure each
Guide Rod with one M10 x 1” Allen Bolt (#47) and ∅ ¾” Washer (#59) from the
bottom.

C.) Attach the rear of Main Frame (#1) to the Rear Base Frame. Secure them with two

M10 x 2 ¾” Carriage Bolts (#46), one U-shaped Bracket (#16), two Ø ¾” Washers
(#59), and two M10 Aircraft Nuts (#56).

D.) Attach the Front Post (#6) to the Main Frame. Secure them with two M10 x 2 ¾”

Carriage Bolts (#46), one 4 ¾” x 2” Bracket (#18), two Ø ¾” Washers (#59), and
two M10 Aircraft Nuts (#56).

E.) Attach the Seat Support (#17) onto the Main Frame. Secure them with two M10 x

2 ¾” Carriage Bolts (#46), one 4 ¾” x 2” Bracket (#18), two Ø ¾” Washers (#59),
and two M10 Aircraft Nuts (#56).

F.) Attach the Foot Plate (#14) onto the Front Post. Secure it with two M10 x 5/8”

Allen Bolts (#48) and two Ø ¾” Washers (#59).

7

DIAGRAM 1

8

STEP 2 (See Diagram 2)

A.) Attach the Vertical Frame (#2) onto the Main Frame (#1). Secure them with two M10 x 2 ¾”

Carriage Bolts (#46), one 5 ½” x 2” Bracket (#12), two Ø ¾” Washers (#59), and two M10
Aircraft Nuts (#56).

B.) Slide 14 Weight Plates (#40) onto the Guide Rods (#10). Make sure the deep grooves on the

Plates all face down and toward to the back of the machine. Insert a Selector Rod (#9) into
the center hole on the Plates. Slide the Selector Stem (#39) onto the Guide Rods. Use the
Weight Selector Pin (#38) to select the number of Wight Pates to exercise. Please refer to
the Weight Resistance Chart in page-19.

C.) Attach the Upper Frame (#3) in between the two Guide Rods. Secure each Guide Rod to

Upper Frame with one M10 x 1 ¾” Allen Bolt (#54) and Ø ¾” x Ø ½” Curved Washer (#61).

D.) Place the Upper Frame onto the Vertical Frame. Secure it with two M10 x 2 ¾” Carriage

Bolts (#46), one 5 ½” x 2” Bracket (#12), two ∅ ¾” Washers (#59), and two M10 Aircraft

Nuts (#56).
E.) Securely tighten all Nuts and Bolts installed in Step-1 and Step-2.
F.) Attach the Leg Developer (#7) to the Front Post (#6). Secure it with one M12 x 3 1/8” Allen

Bolt (#49), two Ø 1” Washers (#60), and one M12 Aircraft Nut (#57).

9

DIAGRAM 2

10

STEP 3 (See Diagram 3)

A.) Attach the Front Press (#4) to the Upper Frame (#3). Secure it with one Front Press Axle

(#27), two Ø ¾” Washers (#59), and two M10 Aircraft Nuts (#56). Do not over tighten the

Nuts. Make sure the Front Press can move smoothly.
B.) Insert the two Front Press Handles (#15) into the arms of Front Press. Secure each Handle

with one M10 x 1” Allen Bolt (#47) and one Ø ¾” x Ø 1” Curved Washer (#62).
C.) Attach the Backrest Board (#30) to the Vertical Frame (#2). Secure it with two M8 x 2 ½”

Allen Bolts (#51) and two Ø 5/8” Washers (#58).

DIAGRAM 3

11

STEP-4 (See Diagram 4)

A.) Attach the Seat Pad (#31) to the Seat Support (#17). Secure it with two M8 x 1 5/8” Allen

Bolts (#52) and Ø 5/8” Washers (#58).

B.) Insert two Foam Tubes (#13) halfway through the holes on Front Post (#6) and Leg

Developer (#7).

C.) Push four Foam Rolls (#24) onto the Tubes from both ends.

DIAGRAM 4

12

CABLE LOOP DIAGRAM

13

STEP 5 (See Diagram 5 & Cable Loop Diagram)

A.) Attach the 182” Upper Cable (#41) to the front opening on the Upper Frame (#3).

NOTE: The Ball Stopper on the Cable needs to be underneath the Frame.

B.) Attach a Pulley (#26) to the opening. Secure it with one M10 x 2 ½” Allen Bolt

(#53), two Ø 7/8” Bushings (#23), and one M10 Aircraft Nut (#56).

C.) Draw the Cable towards the back of the machine to another opening on the Upper

Frame. Repeat Procedure B above to install a Pulley.

D.) Draw the Cable around the Pulley then pull back to the opening on the Front Press

(#4). Attach a Pulley to the opening. Secure it with one M10 x 6 1/8” Allen Bolt
(#50), two Ø ¾” Washers (#59), and one M10 Aircraft Nut (#56).

E.) Draw the Cable around the Pulley then to the opening on the Vertical Frame (#2).

Repeat Procedure B to install a Pulley.

F.) Draw the Cable around the Pulley then back to the lower opening on the Front

Press. Repeat Procedure D to install a Pulley.

G.) Draw the Cable around the Pulley then back to the lower opening on the Vertical

Frame. Repeat Procedure B to install a Pulley.

H.) Draw the Cable over the Pulley and pull the Cable downwards. Attach a Pulley to

the upper holes on the two Double Floating Pulley Brackets (#11).

I.) Attach a Pulley to the Brackets. Secure it with one M10 x 1 ¾” Allen Bolt (#54), two

Ø ¾” Washers (#59), and one M10 Aircraft Nut (#56). Let the Brackets hanging for
now.

J.) Draw the Cable around the Pulley then pull upwards to the opening on the rear

Upper Frame. Repeat Procedure B to install a Pulley.

K.) Pull the Cable downwards between the two Guide Rods to the Selector Rod (#9).

Securely thread the bolt at the end of the Cable into the Selector Rod.

L.) Connect Lat Bat (#8) to the Cable with one Chain (#45) and two Hooks (#43).

14

DIAGRAM 5

15

STEP 6 (See Diagram 6 & Cable Loop Diagram)

A.) Attach the 110” Lower Cable (#42) to the opening on the bottom of the Leg

Developer (#7).

B.) Attach a Pulley (#26) to the opening. Secure it with one M10 x 2 ½” Allen Bolt

(#53), two Ø 7/8” Bushings (#23), and one M10 Aircraft Nut (#56).

C.) Draw the Cable underneath the Pulley towards the back of the machine through

the opening on the Front Post (#6) to the open bracket on rear of Front Post.

D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#54),

two Ø ¾” Washers (#59), and one M10 Aircraft Nut (#56).

E.) Draw the Cable underneath the Pulley towards the back of the machine to the

opening on the Main Base Frame (#1). Repeat Procedure B to install a Pulley.

F.) Draw the Cable around the Pulley then pull upward to the Double Floating Pulley

Bracket (#11) previously installed in Step-5. Repeat Procedure D to install a
Pulley.

G.) Draw the Cable around the Pulley then pull downward to the bracket on the rear

of Main Frame. Secure the Cable to the bracket with one M10 x 1” Allen Bolt
(#47), two ∅ ¾” Washers (#59) and one M10 Aircraft Nut (#56).

H.) Adjust the tension of the Cable system by adjusting the Pulley position on the

Brackets. If the Cables are too loose, move the Pulley up one hole. If the Cables
are too tight, move the Pulley down one hole.

I.) For best performance of the machine, adjust the Cables so the Selector Stem

(Top Plate) on the weight stack is ¼” above the first plate. To select the weight,
push down on the Selector Stem to close the gap then insert the Weight Selector
Pin. This will remove the slack in the cable system so the range of motion is
smooth and tight.

J.) Attach the Ankle Strap (#44) to the Cable for various Leg exercises. Remove the

Ankle Strap when using the Leg Developer.

K.) Lubricate the two Guide Rods with WD-40 or light oil. This will minimize the

friction on the Rods so the weight plates can slide up and down on the rods more
freely.

16

DIAGRAM 6

110＂

17

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Main Frame 1 51 M8 x 2 ½” Allen Bolt 2
2 Vertical Frame 1 52 M8 x 1 5/8” Allen Bolt 2
3 Upper Frame 1 53 M10 x 2 ½” Allen Bolt 7
4 Front Press 1 54 M10 x 1 ¾” Allen Bolt 5
5 Rear Base Frame 1 55 M6 x 5/8” Philips Screw 1
6 Front Post 1 56 M10 Aircraft Nut 25
7 Leg Developer 1 57 M12 Aircraft Nut 1
8 Lat Bar 1 58 Ø 5/8” Washer 4
9 Selector Rod 1 59 Ø ¾” Washer 28
10 Guide Rod 2 60 Ø 1” Washer 2
11 Double Floating Pulley Bracket 2 61 Ø ¾” x Ø ½” Curved Washer 2
12 5 ½” x 2” Bracket 2 62 Ø ¾” x Ø 1” Curved Washer 2
13 Foam Tube 2
14 Foot Plate 1
15 Front Press Handle 2
16 U-shaped Bracket 1
17 Seat Support 1
18 4 ¾” x 2” Bracket 2
19 Ø 2” End Cap 2
20 Ø 1 ¾” x 1 5/8” Rubber Bumper 1
21 Ø 1” x Ø ½” Bushing 2
22 Ø 1” x Ø 5/8” Bushing 6
23 Ø 7/8” Bushing 14
24 Foam Roll 4
25 2” Rear Base Frame End Cap 2
26 Pulley 12
27 Front Press Axle 1
28 Handle Grip 6
29 Ø 1” x 1/8” End Cap 2
30 Backrest Board 1
31 Seat Pad 1
32 1” x 2” End Cap 6
33 Ø 2 ½” x 1” Rubber Bumper 2
34 Ø 2” End Cap 2
35 2” End Cap 3
36 Ø 1” Flat End Cap 4
37 Ø 1” Cone-shaped End Cap 1
38 Weight Selector Pin 1
39 Selector Stem 1
40 Weight Plate 14
41 182” Upper Cable 1
42 110” Lower Cable 1
43 Hook 2
44 Ankle Strap 1
45 Chain 1
46 M10 x 2 ¾” Carriage Bolt 10
47 M10 x 1” Allen Bolt 5
48 M10 x 5/8” Allen Bolt 2
49 M12 x 3 1/8” Allen Bolt 1
50 M10 x 6 1/8” Allen Bolt 2

18

WEIGHT RESISTANCE CHART

WEIGHT PLATE

Station

Lat Pull

Low Pulley

Front Press

Leg Developer

Station

Lat Pull

Low Pulley

Front Press

1 2 3 4 5 6 7 8 9
30 40 50 60 70 80 90 100 110
22 33 44 55 66 77 88 99 110
20 34 48 62 76 90 104 118 132
26 38 50 62 74 86 98 110 122

WEIGHT PLATE

10 11 12 13 14
120 130 140 150 160
121 132 143 154 165
146 160 174 188 202

Leg Developer

Note: Each plate weights 10 lbs.
Numbers are approximate.
Actual we ights may vary.

134 146 158 170 182

19

IMPEX® INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX®") warrants this product to be free f rom defects in workmanship and m aterial, under
normal use and service conditions , f or a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to
replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, m isus e, improper or abnorm al usage or repairs not provided by an
IMPEX authorized service center or for pr oducts us ed f or commercial or rental purposes. No other warr anty
beyond that specifically set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or prof its , los s of enj oyments or us e, cos ts of r emoval, installation or other
consequential damages or whatsoever natures. Som e states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a par ticular purpose is limited in its s cope and duration to the terms set f orth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state to state.

Register on-line a t www.impe x-fitne ss.co m

IMPEX

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS

Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

20

®

INC.