Impex MWM 1801 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

MARCY HOME GYM

MWM 1801

Model

MWM 1801

Retain This

Manual for

Reference

08-18-03

OWNER'S
MANUAL

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

IMPEX FITNESS PRODUCTS

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2

HARDWARE PACK……….....….....................................................................……….. 3

ASSEMBLY INSTRUCTIONS.........................................................................……….. 5

HOW TO USE..................................................................................................………. 25

PARTS LIST………………………………………………………………………………….. 26

RESISTANCE CHART………….......................................................................………. 27

WARRANTY.................................................................................................…………. 28

ORDERING PARTS.......................................................................................………… 28

BEFORE YOU BEGIN

Thank you for selecting the MARCY MWM 1801 HOME GYM by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed to
provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOO-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

HARDWARE PACK

4

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended this machine to be assembled by two or more people to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Left Base Frame (#3) to the Right Base Frame (#1). Secure them with one Bracket

(#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft
Nuts (#90).

DIAGRAM 1

5

STEP 2 (See Diagram 2)

A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10

x 2 ½” Carriage Bolts (#82), ∅ ¾” Washers (#93), and M10 Aircraft Nuts (#90). NOTE:
Do not tighten the Nuts and Bolts yet.

B.) Attach the Right Seat Support (#8) to the Right Base Frame (#1). Secure it with one M10

x 2 ½” Carriage Bolt (#82), ∅ ¾” Washer (#93), and M10 Aircraft Nut (#90).

C.) Attach the Right Seat Support (#8) to the Right Vertical Beam (#2). Secure it with one

Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two
M10 Aircraft Nuts (#90).

D.) Attach the Leg Developer (#9) to the Right Seat Support (#8). Secure it with one M10 x 2”

Axle (#56), two M10 x ¾” Allen Bolts (#86), and two ∅ ¾” Washers (#93). NOTE: Do not
over tighten the bolts. Make sure the Leg Developer is able to swivel.

DIAGRAM 2

6

STEP 3 (See Diagram 3)

A.) Align four ∅ 2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame

(#1). Insert four Guide Rods (#5) through the Rubber Bumpers into the holes on the
Right Base Frame. Slide two Selector Stems (#35) onto the Guide Rods. Insert a
Selector Rod (#24) through the hole on each Selector Stem. Secure each Selector
Rod to the Selector Stem with two M10 x 1” Allen Bolts (#78) and ∅ ¾” Washers
(#93). Please note this machine comes with 18 plates, 9 to each stack. You can
purchase another 5 more plates (Model no. WK51) in the future to increase the
weights. It is strongly recommended to spay lubricant such as WD-40 on the two
Guide Rods to minimize friction.

B.) Attach the Right Upper Frame (#6) to the top of Right Vertical Beam (#2). Secure it

with a Pulley Bracket (#46), two M10 x 2 ½” Carriage Bolts (#82), two Ø ¾” Washers
(#93), and two M10 Aircraft Nuts (#90).

C.) Attach the Top Socket Assembly (#7) to the four Guide Rods. Make sure the Guide

Rods are inserted into the holes on the Top Socket Assembly. Secure the Top Socket
Assembly to the Guide Rods with four M10 x 1” Allen Bolts (#78) and ∅ ¾” Washers
(#93).

D.) Secure the Top Socket Assembly (#7) to the Right Upper Frame (#6) with two M10 x

2 3/8” Carriage Bolts (#80), ∅3/4” Washers (#93) and M10 Aircraft Nuts (#90).

E.) Carefully tilt over the machine with a help of another person. Secure the Guide Rods

(#5) to the Right Base Frame (#1) with four ∅ ¾” Washers (#93) and M10 x 1” Allen
Bolts (#78).

F.) Securely tighten all Nuts and Bolts previously installed.

7

DIAGRAM 3

8

STEP 4 (See Diagram 4)

A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3). Secure it with two

M10 x 2 ½” Carriage Bolts (#82), ∅ ¾” Washers (#93), and M10 Aircraft Nuts (#90).

B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left

Vertical Beam. Secure the Frame to the Left Vertical Beam with one Bracket (#47),
two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft
Nuts (#90). Secure the Frame to the Top Socket Assembly with one Bracket (#47),
two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93), and two M10 Aircraft
Nuts (#90).

C.) Attach the Left Seat Support (#14) to the Left Base Frame (#3) and the Left Vertical

Beam (#4). Secure it to the Left Base Frame with one M10 x 2 ½” Carriage Bolt
(#82), ∅ ¾” Washer (#93), and M10 Aircraft Nut (#90). Secure it to the Vertical
Beam with one Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾”
Washers (#93), and two M10 Aircraft Nuts (#90).

D.) Attach the Leg Press Frame (#17) to the bracket on the Left Base Frame (#3).

Secure it with one M12 x 3” Allen Bolt (#77), two ∅ 1” Washers (#92), and one M12
Aircraft Nut (#89). Do not over tighten the Nut and Bolt. Make sure the Leg Press
Frame is able to swivel.

E.) Attach the Leg Press Support Frames (#18) to both side of the Leg Press Frame

(#17). Secure them together with two M10 x 2 ½” Carriage Bolts (#82), ∅ ¾”
Washers (#93), and M10 Aircraft Nuts (#90).

9

DIAGRAM 4

10

STEP 5 (See Diagram 5)

A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure it with a

M10 x 9 ¼” Axle (#50), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#90).

B.) Attach the two Front Presses (#16) to the Front Press Base (#15). Secure each

Front Press with two M10 x 2 ½” Carriage Bolts (#82), two ∅ ¾” Washers (#93),
and two M10 Aircraft Nuts (#90).

DIAGRAM 5

11

STEP 6 (See Diagram 6)

A.) Insert the axle on the Left Butterfly (#12) through the hole on the Left Upper Frame

(#11) from the bottom up. Slide a ∅ 1 ½” Washer (#54) and ∅ 1 3/8” Lock Ring (#53)
onto the Axle. Align the holes and secure the Ring with a M6 x 1 5/8” Hex Bolt (#87)
and M6 Aircraft Nut (#91). Repeat the same procedure to install the other side.

B.) Push two Butterfly Foam Rolls (#39) onto the Butterfly arms.

DIAGRAM 6

12

Cable Loop Diagram for Butterfly Station

13

Cable Loop Diagram for Bench Press Station

14

STEP 7 (See Diagram 7 & Cable Loop Diagram)

A.) Attach the two Swivel Pulley Brackets (#42) to the Left Upper Frame (#11). Secure each

Bracket with one M12 x 4 3/8” Allen Bolt (#76), two ∅1” Washers (#92) and one M12 Aircraft
Nut (#89). NOTE: Do not over tighten the Bolt. Make sure the Bracket is able to swivel.

B.) Attach one end of the 83” Butterfly Cable (#29) to the clip on the Right Butterfly (#13). Pull

the Cable to the right open Swivel Pulley Bracket (#42).

C.) Attach a Pulley (#65) to the Bracket. Secure it with one M10 x 2 “Allen Bolt (#81), two ∅ ¾”

Washers (#93), and one M10 Aircraft Nut (#90).

D.) Draw the Cable downward. Repeat Step B above to install a Pulley to the Angled Double

Pulley Bracket (#45). Let the Bracket hanging for now. Pull the Cable upward to the left
open Swivel Pulley Bracket.

E.) Repeat Step B above to install another Pulley to the Left Swivel Pulley Bracket. Draw the

Cable to the Left Butterfly (#12). Attach the end of the Cable to the clip on the Left Butterfly.

DIAGRAM 7

15

STEP 8 (See Diagram 8 & Cable Loop Diagram)

A.) Attach a Chain (#51) to the Left Vertical Beam (#4). Secure it with one M10 x 1 3/8”

Allen Bolt (#83), two ∅ 3/4” Washers (#93), and one M10 Aircraft Nut (#90). Attach one
end of the 136” Butterfly Support Cable (#31) to the Chain using a C-clip (#63). NOTE:
After complete installing all the cables, check the tightness of the cable loop system. If

the cable is too loose, shorten the chain.
B.) Draw the Cable to the Angled Double Pulley Bracket (#45) previously installed.
C.) Attach a Pulley to the Bracket. Secure it with one M10 x 2” Allen Bolt (#81), two ∅ ¾”

Washers (#93), and one M10 Aircraft Nut (#90).
D.) Pull the Cable around the Pulley then downward. Repeat Step C above to install a

Pulley to a Single Floating Pulley Bracket (#43). Let the Bracket hanging for now. Draw

the Cable underneath the Pulley then upward through the Left Upper Frame (#11) to

the open Bracket on the top.
E.) Attach a U-shaped Bracket (#49) to the Bracket. Repeat Step C above to install a

Pulley. Draw the Cable over the Pulley then pull the Cable downward to the Selector

Rod (#24). Thread the tip bolt of the Cable into the Selector Rod.

16

STEP 9 (See Diagram 9 & Cable Loop Diagram)

A.) Attach one end of the140” Leg Press Cable (#28) to the opening hole on the Left Seat

Support (#14), underneath the rubber bumper. Secure it with one M10 x 2 3/8” Allen
Bolt (#79), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).

B.) Draw the Cable to the slotted opening on the Leg Press Frame (#17). Install a Pulley to

the opening then secure it with two ∅5/8” x ½” Pulley Bushings (#58), one M10 x 2 3/8”
Allen Bolt (#79), and one M10 Aircraft Nut (#90).

C.) Draw the Cable around the Pulley then toward the opening on the Left Seat Support

(#14). Repeat the Step B above to install a Pulley.

D.) Draw the Cable over the Pulley then downward to the open bracket on the Left Base

Frame (#3). Attach a Pulley to the Bracket then secure it with one M10 x 2” Allen Bolt
(#81), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).

E.) Draw the Cable underneath the Pulley and towards the back of the machine, along the

Left Base Frame to the lower opening on the Left Vertical Beam (#4). Repeat Step B
above to install a Pulley. Draw the Cable around the Pulley then pull back towards the
lower opening on the Front Press Base (#15).

F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#75), two ∅ ¾”

Washers (#93), and one M10 Aircraft Nut (#90).

G.) Draw the cable around the Pulley then pull the Cable towards the open bracket on the

Left Vertical Beam. Attach a U-shaped Bracket (#49) to the open Bracket. Install
another Pulley. Secure them with one M10 x 2” Allen Bolt (#81), two ∅ ¾” Washers
(#93), and one M10 Aircraft Nut (#90).

H.) Draw the Cable around the Pulley then back to the upper opening on the Front Press

Base (#15). Repeat Step F above to install another Pulley.

I.) Draw the Cable around the Pulley then towards the upper slotted opening on the Left

Vertical Beam (#4). Repeat Step B above to install a Pulley.

J.) Draw the Cable over the Pulley then downward to the open bracket on the Left Base

Frame. Install a Pulley. Secure the Pulley with an L-shaped Bracket (#48), one M10 x 2”
Allen Bolt (#81), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).

K.) Draw the Cable underneath the Pulley then pull the Cable upward to the Single Floating

Pulley Bracket (#43) previously installed. Secure the Cable with one M10 x 1 3/8”” Allen
Bolt (#83), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).

17

DIAGRAM 9

18

STEP 10 (See Diagram 10 & Cable Loop Diagram)
A.) Attach the 114” Upper Cable (#26) to the front opening on the Right Upper Frame (#6).

NOTE: The Ball Stopper on the Cable needs to be underneath the Frame.

B.) Attach a Pulley (#65) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅

5/8” x ½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90).

C.) Draw the Cable towards the back of the machine to the Pulley Bracket (#46). Install a Pulley

to the Bracket. Secure it with one M10 x 2” Allen Bolt (#81), one L-shaped Bracket (#48), two
∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).

D.) Pull the Cable over the Pulley then downward. Attach a Pulley to a Double Floating Pulley

Bracket (#44). Secure it with one M10 x 2” Allen Bolt (#81), two ∅ ¾” Washers (#93), and
one M10 Aircraft Nut (#90). Let the Bracket hanging for now.

E.) Pull the Cable around the Pulley then upward to the open bracket on the back of the Top

Socket Assembly (#7). Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt
(#81), U-shaped Bracket (#49), two ∅ ¾” Washers (#93), and one M10 Aircraft Nut (#90).

F.) Pull the Cable around the Pulley then downward to the Selector Rod (#24). Thread the bolt

at the end of the Cable into the Selector Rod.

19

STEP 11 (See Diagram 11 & Cable Loop Diagram)

A.) Attach the 39” AB Cable (#30) to the opening on the Right Vertical Beam (#2). Attach

a Pulley to the opening. Secure the Pulley with one M10 x 2 3/8” Allen Bolt (#79), two
∅ 5/8” x ½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90).

B.) Pull the AB Cable around the Pulley then downward. Attach the end of Cable to a

Chain (#51). Secure the Cable to the Chain with one M10 x 1” Allen Bolt (#78), two ∅
¾” Washers (#93), and one M10 Aircraft Nut (#90). Let the Chain hanging for now.

C.) Attach the 171” Lower Cable (#27) to the opening on the Leg Developer (#9). Attach a

Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅ 5/8” x
½” Pulley Bushings (#58), and one M10 Aircraft Nut (#90). Draw the Lower Cable
underneath the Pulley through the opening on the Right Seat Support (#8) then to the
open bracket on the Right Base Frame (#1).

D.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#81), two ∅ ¾”

Washers (#93), and one M10 Aircraft Nut (#90).

E.) Draw the Lower Cable underneath the Pulley along the Right Base Frame and

through the opening on the Right Vertical Beam (#2) to the second open bracket on
the Right Base Frame. Attach a L-shaped Bracket (#48) to the bracket then repeat
Step D above to install a Pulley.

F.) Pull the Cable underneath the Pulley then upward to the Double Floating Pulley

Bracket (#44) previously installed. Repeat Step D above to install a Pulley.

G.) Draw the Cable around the Pulley then pull the Cable downward to the first Bracket

on the Right Base Frame. Install another Pulley.

H.) Pull the Cable around the Pulley then upward to the Chain (#51). Connect the Cable

to the end of the Chain using a C-clip (#63).

I.) Check the tightness of the Cable loop system. If the cable loop is too loose, shorten

the chain.

20

DIAGRAM 11

21

STEP 12 (See Diagram 12)
A.) Now move the machine to its fina l p osition. After installing the weight stack, it will be too heavy to

move. Check and tighten all Nuts and Bolts previously installed.

B.) Install 9 Weight Plates (#36) to each set of Guide Rods (#5). To install the plate, lift up the

Selector Rod in the center, hold the plate at an angle and place between the two Guide Rods then
drop it down. NOTE: Make sure the groves on the plastic covers all face the same direction. The
caps should interlock with each other.

C.) Align the center holes on all plates. Insert the Selector Rod (#24) into the center holes on the

plates. Insert the Weight Selector Pin (#52) into the selected stack of Weight Plates to obtain the
desired weight for exercise. Make sure the magnet on the Pin faces up. It is strongly
recommended to spray lubricant such as WD-40 on the two Guide Rods to minimize friction.

D.) Attach the Backrest Board (#23) to the Right Vertical Beam (#2). Secure it with two M8 x 2 1/8”

Allen Bolts (#84) and ∅ 5/8” Washers (#94).

E.) Place the Seat (#22) onto the Right Seat Support (#8). Secure it with two M8 x 2 1/8” Allen Bolts

(#84) and two ∅ 5/8” Washers (#94).

F.) Attach the Arm Curl Pad (#21) to the Arm Curl Stand (#10). Secure it with two M8 x 5/8” Allen Bolts

(#85) and ∅ 5/8” Washers (#94). Insert the Arm Curl Stand into the top opening on the Right Seat
Support. Use a M18 Lock Knob (#64) to hold the desired height for Arm Curl exercise.

22

STEP 13 (See Diagram 13)
A.) Insert one Foam Tube (#34) halfway through the hole on the Right Seat Support (#8). Insert

one Foam Tube (#34) halfway through the hole on the Leg Developer (#9). Push four Foam
Rolls (#38) onto the Tubes from both sides. Plug the Foam Roll End Caps (#74) into the ends.

B.) Attach the Lat Bar (#20) to the Chain (#51) using a C-clip (#63). Attach the Chain to the Upper

Cable (#26). See How To Use.
C.) Attach the AB Strap (#25) to the AB Cable (#30) using a C-clip.
D.) Attach the Arm Curl Handle (#32) to a Chain (#51) using a C-clip. Attach the Chain to the

Lower Cable (#27). Remove the Chain and Handle when using the Leg Developer.

DIAGRAM 13

23

STEP 14 (See Diagram 14)
A.) Attach a Backrest Board (#23) to the Left Vertical Beam (#4). Secure it with two M8 x 2 1/8”

Allen Bolts (#84) and ∅ 5/8” Washers (#94).

B.) Place the Seat (#22) onto the Left Seat Support (#14). Secure it with two M8 x 2 1/8” Allen

Bolts (#84) and two ∅ 5/8” Washers (#94).

C.) Attach the Leg Press Plate (#19) to the Leg Press Frame (#17). Secure it with a L-Shaped

Pin (#62).

DIAGRAM 14

24

HOW TO USE

How to use the quick release connector.

The Clip is removed from the Connector.

Connector

Clip

Place the chain in between the connector

Insert

and insert the Clip through the holes.

Chain

Push down the Clip to secure.

25

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Right Base Frame 1
2 Right Vertical Beam 1
3 Left Base Frame 1
4 Left Vertical Beam 1
5 Guide Rod 4
6 Right Upper Frame 1
7 Top Socket Assembly 1
8 Right Seat Support 1
9 Leg Developer 1
10 Arm Curl Stand 1
11 Left Upper Frame 1
12 Left Butterfly 1
13 Right Butterfly 1
14 Left Seat Support 1
15 Front Press Base 1
16 Front Press 2
17 Leg Press Frame 1
18 Leg Press Support Frame 2
19 Leg Press Plate 1
20 Lat Bar 1
21 Arm Curl Pad 1
22 Seat 2
23 Backrest Board 2
24 Selector Rod 2
25 AB Strap 1
26 114” Upper Cable 1
27 171” Lower Cable 1
28 140” Leg Press Cable 1
29 83” Butterfly Cable 1
30 39” AB Cable 1
31 136” Butterfly Support Cable 1
32 Arm Curl Handle 1
33 Curl Bar Handle Tube 1
34 Foam Tube 2
35 Selector Stem 2
36 Weight Plate 18
37 Weight Plate Cover 36
38 Foam Roll 4
39 Butterfly Foam Roll 2
40 Lat Bar Grip 2
41 Handle Grip 4
42 Swivel Pulley Bracket 2
43 Single Floating Pulley Bracket 1
44 Double Floating Pulley Bracket 1
45 Angled Double Pulley Bracket 1
46 Pulley Bracket 1
47 Bracket 5
48 L-shaped Bracket 3
49 U-shaped Bracket 4
50 M10 x 9 ¼” Axle 1

51 Chain 4
52 Weight Selector Pin 2
53 Ø 1 3/8” Lock Ring 2
54 Ø 1 ½” Washer 2
55 Butterfly Axle 2
56 M10 x 2” Axle 1
57 Ø 1 3/8” Selector Stem Bushing 4
58 Ø 5/8” x ½” Pulley Bushing 14
59 Ø 1 3/8” x 1” Bushing 2
60 Ø 5/8” Bushing 8
61 ∅ ½” Bushing 2
62 L-shaped Pin 1
63 C-clip 5
64 M18 Lock Knob 1
65 Pulley 25
66 Ø 1 ½” x 5/8” Rubber Bumper 1
67 Ø 1 5/8” x 1 5/8” Rubber Bumper 2
68 Ø 2 ½” x 1” Rubber Bumper 4
69 1 ½” Square End Cap 1
70 1 ¾” Square Sleeve 1
71 2” Square End Cap (Impex Logo) 2
72 1 ¾” Square End Cap (Impex Logo) 19
73 1 ½” Square End Cap (Impex Logo) 2
74 Foam Roll End Cap 4
75 M10 x 8 ¼” Allen Bolt 2
76 M12 x 4 3/8” Allen Bolt 2
77 M12 x 3” Allen Bolt 1
78 M10 x 1” Allen Bolt 13
79 M10 x 2 3/8” Allen Bolt 8
80 M10 x 2 3/8” Carriage Bolt 2
81 M10 x 2” Allen Bolt 16
82 M10 x 2 ½” Carriage Bolt 24
83 M10 x 1 3/8” Allen Bolt 2
84 M8 x 2 1/8” Allen Bolt 8
85 M8 x 5/8” Allen Bolt 2
86 M10 x ¾” Allen Bolt 2
87 M6 x 1 5/8” Hex Bolt 2
88 M6 x 5/8” Philips Screw 3
89 M12 Aircraft Nut 3
90 M10 Aircraft Nut 57
91 M6 Aircraft Nut 2
92 ∅ 1” Washer 6
93 Ø ¾” Washer 82
94 Ø 5/8” Washer 11

26

MWM 1801 Weight Resistance Chart

Weight Plate

Station 1 2 3 4 5 6 7 8 9

Low Pulley 30 42 54 66 78 90 102 114 126

Lat Pull 31 42 53 64 75 86 97 108 119
Ab Strap 30 42 54 66 78 90 102 114 126
Butterfly 20 26 32 38 44 50 56 62 68

Leg Press 66 100 134 168 202 236 270 304 338

Front Press 44 63 82 101 120 139 158 177 196

*Each plate weights 10 lb.
*Resistance measured in pounds.
*Numbers are approxima te. Actual number may vary.

27

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this pr oduct to be f ree fr om def ects in workm ans hip and m aterial,
under normal use and service c onditions , f or a per iod of two years on the Fr ame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for produc ts
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or cons equential damages aris ing out of or
in connection with the use or performance of the pr oduct or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, cos ts of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of inc idental or consequential damages. Accordingly, the above
limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is lim ited in its sc ope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state
to state.

ORDERING REPLACEMENT PARTS
Replacement parts can be order ed by calling our Custom er Ser vice Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

Register on-line a t www.impe x-fitne ss.co m

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

28