Impex MWB CR 4 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

How to Use

Warranty

Ordering Parts

MARCY CORNER GYM

CR 4

Model

MWB CR 4

Retain This

Manual for

Reference

6-18-01

OWNER'S

MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex -fitness.com

info@impex -fitness.com

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER .....…....................................................................... 3

ASSEMBLY INSTRUCTIONS........................................................................... 4

PARTS LIST…………………………………………………………….…………….21
RESISTANT CHART…………………………………………………………………22
HOW TO USE…………………………………………………………………………23

WARRANTY.................................................................................................… 24

ORDERING PARTS......................................................................................... 24

BEFORE YOU BEGIN

Thank you for selecting the MARCY CR4 PERSONAL TRAINER by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual carefully
before using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call
our TOO-FREE customer service num ber. Our Customer Service Agents will
provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you
operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or
operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the mach ine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING
ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.

SAVE THESE INSTRUCTIONS.

2

3

ASSEMBLY INSTRUCTION

Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more people to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#1) and Left Base Frame (#2) on the floor, at a right angle to each

other. Attach the Rear Vertical Beam (#5) to the joint and align the holes. Secure the top hole
with a M10 x 2 ¾” Carriage Bolt (#90), ∅3/4” Washer (#106) and M10 Aircraft Nut (#110). Secure
the bottom hole with a M10 x 2 ½” Allen Bolt (#97) and ∅ ¾” Washer (#106). DO NOT tighten all
the nuts and bolts yet.

B.) Attach the Guide Rod Base (#24) diagonally to the two Base Frames. Secure it with a M10 x 2 ½”

Allen Bolt (#97) and ∅1 ¼” Washer (#104) on each side on the Base.

C.) Attach the Right Vertical Beam (#3) to the Right Base Frame (#1). Secure it with two M10 x 2 ¾”

Carriage Bolts (#90), ∅3/4” Washers (#106), and M10 Aircraft Nuts (#110). Repeat the same
procedure to install the Left Vertical Beam (#4).

Diagram 1

4

STEP 2 (See Diagram 2)

A.) Attach the Right Upper Frame (#6) to the top of the Right Vertical Beam (#3). Secure it with two

M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅3/4” Washers (#106), and two
M10 Aircraft Nuts (#110).

B.) Attach the Left Upper Frame (#7) to the Left Vertical Beam (#4). Secure it with one M10 x 2 ½”

Allen Bolt (#97), ∅ ¾” Washer (#106), and 4” x 2” Bracket (#39) into the upper hole. Secure the
bottom hole with one M10 x 2 ¾” Carriage Bolt (#90), ∅ ¾” Washer (#106), and M10 Aircraft Nut
(#110).

C.) Attach both Left and Right Upper Frame (#7) & (#6) to the Rear Vertical Beam (#5). Secure it with

a M10 x 2 ½” Allen Bolt (#97) and ∅ ¾” Washer (#106) to the upper hole. Secure the bottom hole
with a M10 x 2 ¾” Carriage Bolt (#90), ∅ ¾” Washer (#106) and M10 Aircraft Nut (#110).

D.) Align two Rubber Bumpers (#63) to the holes on the Guide Rod Base (#24). Push two Guide

Rods (#31) into the holes. Slide the Selector Stem (#44) onto the Guide Rods. Slide the Selector
Stem over the Selector Rod (#43). Please note this machine comes with 14 plates. You can
purchase another 5 more plates in the future to increase the weights. For now, drop the Selector
Stem down on the Selector Rod so there are 14 grooves underneath it. Secure it with a M10 x 1 ¾”
Allen Bolt (#98). DO NOT install the plates yet.

E.) Place the Top Socket Assembly (#25) over the top of the two Guide Rods. Secure it with two M6 x

5/8” Allen Bolts (#103).

F.) Secure the Top Socket Assembly (#25) to both Upper Frames (#6) & (#7) with a M10 x 2 ½” Allen

Bolt (#97) and ∅1 ¼” Washer (#104) on each side.

G.) Securely tighten all nuts and bolts previously installed.

5

6

STEP 3 (See Diagram 3)

A.) Attach the Seat Support Frame (#14) to the Right Vertical Beam (#3). Secure it with two M10 x 2

¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106) and two M10 Aircraft
Nuts (#110).

B.) Attach two Vertical Supports (#16) to the front of the Seat Support (#14). Secure them with two

M10 x 2 ¾” Carriage Bolts (#90), ∅ ¾” Washers (#106), and M10 Aircraft Nuts (#110).

DIAGRAM 3

7