Impex MWB-4360 User Manual
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
MARCY®
SMITH MACHINE
MWB-4360
Model
MWB-4360
Retain This
Manual for
Reference
07-14-06
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
TABLE OF CONTENTS
BEFORE YOU BEGIN..................................................................……………. 1
IMPORTANT SAFETY NOTICES.................................................................… 2
SMITH MACHINE HARDWARE PACK….......…............................................. 4
SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................ 6
EXPLODED DIAGRAM……………………………………………………………. 21
SMITH MACHINE PARTS LIST………..………………………………………… 22
MULTI-PURPOSE BENCH HARDWARE PACK……………………………….. 23
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS............................ 24
EXPLODED DIAGRAM…………………………………………………………… 29
MULTI-PURPOSE BENCH PARTS LIST………………………………………… 30
WEIGHT RESISTANCE CHART…………………………………………………… 31
WARRANTY.................................................................................................… 32
ORDERING PARTS.....................................................................................… 32
BEFORE YOU BEGIN
Thank you for selecting the MARCY
safety and benefit, read this manual carefully before using the machine. As a
manufacturer, we are committed to provide you complete customer satisfaction.
If you have any questions, or find there are missing or damaged parts, we
guarantee you complete satisfaction through direct assistance from our factory.
To avoid unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance to
you.
®
MWB-4360 by IMPEX® INC. For your
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
info@impex-fitness.com
1
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
5. Maximum weights on the rack: 600 lbs.
6. Maximum weights on Leg Developer: 100 lbs.
7. Maximum weights on Cross-over, Lat Pull: 200 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Base, Rear Stabilizer, and Upper Frame.
If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements.
Apply the labels in the location shown.
3
SMITH MACHINE HARDWARE PACK
4
SMITH MACHINE HARDWARE PACK
5
SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Base Frames (#1) by a Cross Brace (#2) in the mid-span. Secure each
end of The Cross Brace with two M10 x 3 ½” Carriage Bolts (#79), one 4 ¾” x 2” Bracket
(#36), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86).
B.) NOTE: DO NOT tighten the Nuts and Bolts yet.
DIAGRAM 1
6
STEP 2 (See Diagram 2)
A.) Attach a Front Vertical Frame (#3) to the Right Base Frame (#1). Secure it with two M10 x
3” Carriage Bolts (#76), one 5 1/8” x 2 ¾” Bracket (#34), two Ø ¾” Washers (#66), and
two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts yet.
B.) Align a Ø 2 ½” Rubber Bumper (#59) to the hole on the Base Frame. Insert a Guide Rod
(#25) through the Rubber Bumper and into the Base Frame. Secure it with one M10 x 1”
Allen Bolt (#68) and Ø ¾” Washer (#66).
C.) Slide a Lower Safety Stop Frame (#92) onto the Guide Rod (#25). Secure the Safety
Hook (#93) to the Lower Safety Stop Frame (#92) with a M10 x 1” Allen Bolt (#68) and
M10 Aircraft Nut (#86). Attach the Hook onto the back of the Front Vertical Beam (#3).
D.) Slide a Safety Stop Frame (#26) onto the Guide Rod (#25).
E.) Attach the hole on top of the Right Vertical Frame (#5) to the top of the Guide Rod (#25).
Attach the top of Right Vertical Frame (#5) to the top of Front Vertical Frame (#3). Attach
the bottom of Right Vertical Frame (#5) to the Base Frame (#1).
F.) Secure the Guide Rod (#25) to the Right Vertical Frame (#5) with one M10 x 1” Allen Bolt
(#68) and Ø ¾” Washer (#66).
G.) Secure the Right Vertical Frame (#5) to the Base Frame with two M10 x 3” Carriage Bolts
(#76), one 6 ¼” x 2” Bracket (#37), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts
(#86). Do not tighten the Nuts and Bolts yet.
H.) Secure the Right Vertical Frame (#5) to the Front Vertical Beam (#3) with one Triangle
Bracket (#33), M10 x 3 1/8” Allen Bolt (#72), and ∅ ¾” Washer (#66) to the top hole.
Secure the bottom two holes with two M10 x 3 3/8” Carriage Bolts (#78), ∅ ¾” Washers
(#66) and M10 Aircraft Nuts (#86).
I.) Repeat the above Procedures A through H to install the other side.
J.) Attach the Front Top Beam (#15) to the Front Vertical Beams (#3) and the Triangle
Brackets (#33). Align the Holes. Secure each end with two M10 x 3 3/8” Carriage Bolts
(#78), Ø ¾” Washers (#66), and M10 Aircraft Nuts (#86).
K.) Do NOT tighten all the Nuts and Bolts yet.
L.) NOTE: Periodically lubricate the two chromed Guide Rods (#25) with WD-40 or light oil to
maximize the performance.
7
DIAGRAM 2
8
STEP 3 (See Diagram 3)
A.) Attach the Rear Vertical Beam (#6) to the top of the Cross Brace (#2). Attach the Weight
Glide Base (#8) to the Cross Brace from the Bottom. Align the holes. Secure them with
two M10 x 3” Carriage Bolts (#76), Ø ¾” Washers (#66), and M10 Aircraft Nuts (#86).
B.) Attach the Pulley Support Frame (#97) to the Rear Vertical Beam. Secure it with two M10
x 2 ¾” Carriage Bolts (#75), one 4 ¾” x 2” Bracket (#36), two Ø ¾” Washers (#66), and
two M10 Aircraft Nuts (#86).
C.) Attach the Backrest Board (#38) to the Rear Vertical Beam. Secure it with two M8 x 2 ½”
Allen Bolts (#80) and Ø 5/8” Washers (#65).
9
Loading...