Ik Multimedia iRig BlueBoard USER MANUAL

Wireless MIDI controller/page turner

for iPhone, iPod touch, iPad and Mac

USER MANUAL

Table of Contents

Contents 2

English 3

Safety Information 3 iRig BlueBoard 3 iRig BlueBoard Firmware update 3 Features 4 Register your iRig BlueBoard 5 Installation and setup 5 BlueBoard mode 7

Connecting to the Control App 8 Connecting to Amplitube or VocaLive app 9

MIDI over Bluetooth modes (requires Firmware v.1.2.0) 9

MIDI over Bluetooth mode 1 10 MIDI over Bluetooth mode 2 11

Startup notes 12 Status LED 12 USB Port 13 USB Power 14 Troubleshooting 14 Specifications 14 Warranty 15 Support and more info 15

Regulatory 16

English

Safety Information

• To reduce risk of internal damage or malfunction, never expose the unit to rain, moisture or excessive humidity. Never let any liquid spill on the unit.

• Always remove the batteries if you plan not to use the unit for a long time.

• Never expose the unit to a temperature higher than 60°C (140°F) .

• Never step over the unit or step on it with your full weight, this might cause permanent damages to the iRig

BlueBoard structure and foot switches.

• There are no user serviceable parts inside iRig BlueBoard, never open the unit.

• All servicing should be referred to qualified personnel only.

• iRig BlueBoard communicates via Bluetooth. Never insert iRig BlueBoard into metallic cases or structures

that could shield the Bluetooth signal.

• CAUTION: risk of explosion if battery is replaced by an incorrect type. iRig BlueBoard can ONLY be used with consumer grade, non-rechargeable CARBON-ZINC or ALKALINE batteries.

iRig BlueBoard

Thank you for purchasing iRig BlueBoard, the first wireless MIDI-pedalboard controller for iPhone, iPod touch, iPad and Mac.

Your package contains:

• iRig BlueBoard

• 4 x AAA batteries

• Quick Start Guide

• Registration Card

iRig BlueBoard is the first wireless MIDI pedalboard for iOS and Mac. It allows you to control parameters of your MIDI-compatible apps, like AmpliTube, wirelessly from the floor. Switch between presets, change patches, turn effects on and off and control effects like volume and wah pedals, all from the stage floor, without worrying about tripping over wires. Setup is as simple as turning the iRig BlueBoard on and setting its control assignments in the free control app.

And now iRig BlueBoard can work as a standard BTLE MIDI device, it’s able to directly communicate with apps without the need of an in-between “bridge” app (Firmware update required).

iRig BlueBoard Firmware update

The FW update v1.2.0 allows for the new MIDI over Bluetooth modes operations. You need a unit with this version of FW installed to use the new features of iRig BlueBoard. A firmware updater utility will be available soon. If your unit does not have the last FW installed you can refer only to the “BlueBoard mode” section on this manual.

English

Features

Status LED

Foot switches Connectors for external controllers

Power switch Battery compartment

iRig BlueBoard is equipped with four backlit soft-touch pads housed in a sturdy, stageworthy chassis, two TRS jacks for connecting additional controllers like foot switches and expression pedals, and is powered by four standard AAA batteries.

iRig BlueBoard works by wirelessly connecting to a dedicated iOS and Mac app called “iRig BlueBoard,” which receives Bluetooth control messages from the iRig BlueBoard hardware, and translates them into standard MIDI commands for any hardware or software instrument or MIDI-compatible app like AmpliTube.

The control messages sent from iRig BlueBoard to AmpliTube or other Core MIDI music apps can include MIDI Program Change and Control Change messages, as well as parameter changes on apps such as IK’s AmpliTube, VocaLive, SampleTank and iGrand Piano, or any other Core MIDI compatible app like Apple GarageBand.

USB port

iRig BlueBoard communicates via Bluetooth technology so you can place it up to 10 meters (32.8 feet) away from your device and still maintain full control of your apps.

The four backlit footswitches on iRig BlueBoard will turn ON when the unit is activated (blue backlight).

In addition to this iRig BlueBoard features a low-intensity blue light, which illuminates all four footswitches, making iRig BlueBoard visible on a dark stage. This low-intensity backlight can be turned ON or OFF (to save battery) from the control app.

English

Register your iRig BlueBoard

By registering, you can access technical support, activate your warranty and receive free JamPoints™ which will be added to your account. JamPoints™ allow you to obtain discounts on future IK purchases! Registering also keeps you informed of all the latest software updates and IK products.

Installation and setup

1. Install the four AAA batteries into the battery compartment of iRig BlueBoard. It is very important to follow the polarity indicators for the batteries that are indicated on the internal part of the battery compartment. iRig BlueBoard works with Bluetooth LE technology, allowing for extra-low current consumption and very long battery life.

+ 11 hidden pages