Ikelite DSC-RX100M3/B Instruction Manual

Digital Housing

I n s t r u c t i o n M a n u a l

6116.12 Sony RX100 III (DSC-RX100M3/B)

Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please refer to the back page of this manual to
register your Ikelite product.

Table of Contents

Preparation ..................................................................P. 3

Specifications ..............................................................P. 4

What’s in the Box ........................................................P. 4

Parts of the Housing - Front View ..................................P. 5

Parts of the Housing - Back View ..................................P. 6

Housing and Camera Setup ........................................P. 7

STEP 1 - Initial Camera Setup ........................................P. 7, 8

STEP 2 - Opening the Housing ......................................P. 8

STEP 3 - Attach Camera to Mounting Tray ....................P. 8, 9

STEP 4 - Attach the Control Ring Gear ..........................P. 10

STEP 5 - Installing Camera in Housing ..........................P. 11

STEP 6 - Closing the Housing ........................................P. 11

STEP 7 - Final Check......................................................P. 12

Housing Usage ............................................................P. 12

Zoom Control Use ..........................................................P. 12

Built-in Flash and Strobe Use ....................................P. 13

Strobe Use ......................................................................P. 13

Using Strobes with a Fiber Optic Connection ................P. 13

Using the Camera’s Built-in Flash ..................................P. 14

Deflector Installation and Removal ................................P. 14

Diffuser Purpose..............................................................P. 15

Diffuser Installation and Removal....................................P. 15

Entering the Water ..........................................................P. 16

Recommended Accessories and Attachments ........P. 16 - 20

2

continued

Table of Contents

Maintenance ................................................................P. 21 - 24

Photo Tips ..................................................................P. 25

Troubleshooting ........................................................P. 26 - 28

Spare Parts ..................................................................P. 29

Customer Support ......................................................P. 30

Limited Warranty ........................................................P. 30

Returning Products for Service ................................P. 31

Product Registration ..................................................Back Page

-

Preparation

This product has been water pressure tested at the factory and is depth
rated to 200 ft (60 m). Thoroughly inspect and immerse the empty
housing completely in water before installing a camera. If any fogging
occurs or droplets of water enter the housing, do not install a camera.
Clean the main housing o-ring and retest to make sure that it is
watertight. Refer to the Troubleshooting section, page 26.

Please read your camera manual thoroughly to have a full
understanding of each camera function.

If you are new to underwater photography, be sure to read the Photo
Tips section, page 25.

3

Specifications

Depth Rating..........................200 ft (60 m)

Controls ................................All important camera functions accessed

................................................except Flash switch and Viewfinder switch

Buoyancy ..............................Slight negative buoyancy in fresh water

Housing Weight ....................4.7 lb (2.1 kg)

Strobe Connection................Fiber Optic Ports

Use Built-in Flash..................Yes

Optional Tray Mounting ........12-24 thread external tray mounting with 3 in

................................................(76 mm) spacing

Main O-Ring ..........................0109

Housing Dimensions ............Dimensions 6.8 x 4.8 x 5.4 in (173 x 122 x

...

.............................................137 mm)

(no camera installed)

Housing Material ..................Polycarbonate front, acrylic back

Lens Port ..............................3.0-inch diameter glass

What’s in the Box

- Housing

- Port Cover

- Flash Diffuser

- Flash Deflector (removeable from housing)

- Control Ring Gear with set screws and Allen Wrench

- Silicone 1cc Lubricant Tube

- Allen wrench for control knob set screws

- Control Ring Gear with 3 small set screws installed, 3 extra small set

screws and small allen wrench (in a bag inside housing)

4

Parts of the Housing - Front View

Housing controls are provided for all camera functions except the
flash up switch and viewfinder switch. The built-in camera flash must be
extended BEFORE placing the camera in the housing.

Shutter
Release

Mode Dial

Control Ring

Zoom Lever

ON/OFF (Power) Button

Fiber
Optic
Ports

Lens Port

Lid Snap

External Tray Mount

Control Ring: To properly engage the Control Ring on the surface or in

shallow water, apply slight downward pressure as you rotate the knob.
Always check to see if the Control Ring teeth are meshing properly with
the Housing Control Gear.

5

Parts of the Housing - Back View

1

1. MOVIE Button

2. Fn Function Button

3. MENU Button

3

87

MENU

5

Control
Wheel
Dot

Fn

2

4

6

9

10

7. Set / Tracking Focus

8. Flash Mode / Right Button

9. Exp. Comp. / Down Button

11

Housing
Dot

4. DISP Display / UP Button

5. * Control Wheel

6. Drive Mode / Left Button

* Control Wheel: Note that a small section of the rubber disc is missing at the end of this

control. This is normal and allows the user to completely disengage the control from the

camera when not in use. To disengage Control wheel, rotate Control Wheel Knob to the

6 o’clock position, lining up the Knob’s White Dot with the Housing Dot. Rotate Control

Knob White Dot to

12 o’clock position when attaching or removing Housing Back.

10. Playback Button

11. C / Delete Button

6

Housing and Camera Setup

1

STEP 1 - Initial Camera Setup

Setup your camera for underwater use and then adjust your settings once underwater.

- Set Mode Dial to “A” Aperture Priority. Manually adjust aperture setting to

achieve the best exposure for your shooting conditions. The shutter

speed will be locked at 1/30th second. If a faster shutter speed is

desired, set Mode Dial to “M” Manual mode to manually adjust both

aperture and shutter speed settings.

- In MENU settings:

Set Image Size to “L: 20M” and Aspect Ratio to “3:2” or other preffered

setting.

Set Quality to “X.FINE” Extra Fine.”

Set Drive Mode to “Single Shooting” and Red Eye Reduction to “Off.”

(before placing camera in housing)

Set Focus Mode to “Single-shot AF” and Focus Area to “Center.”

Set AF Illuminator to “Off.”

Set ISO to “200” and ND Filter to “Off.”

Set Metering Mode to “Center” and White Balance to “Auto WB.” For

best results and when using a color filter, manually set white balance

for each working depth.

Set DRO/Auto HDR “OFF.”

Set SteadyShot to “On” and Auto Review to “5 Sec.”

Set Pre-AF to “On” and Zoom Setting to “Optical Zoom Only.”

Set Monitor Brightness to “Manual +1.”

Set Pwr Save Start Time to “5 min.”

Set Date and Time.

Insert and Format a memory card.

- Set Flash Mode to “Fill-flash .”

7

STEP 1 - Initial Camera Setup

- continued

If close-up images are overexposed, adjust aperture setting and/or use

“-” Flash Exposure Compensation and/or back away, zoom in, and

then reshoot.

- RAISE the camera flash before placing camera in housing (no housing

control is provided for this function).

** All camera user settings not listed should be set to the user’s

preference.

STEP 2 - Opening the Housing

Lid Snaps have a Lock.

1. Push Lid Snap Locks forward and lift as shown.

Push Forward

Open opposing Lid Snaps simultaneously. Keep
pressure on the Lid Snaps so they do not fly
open quickly.

Some Lid Snaps have a lot of spring tension

Lift

once they go over center, so keep a firm grip on
each Lid Snap. Lid Snaps may also be opened
one at a time.

2. Remove the Housing Back.

STEP 3 - Attach Camera to Mounting Tray

1. The Mounting Tray for the camera is secured to the housing back.
Position the camera on the Mounting Tray.

2. Using a coin or screwdriver (preferred), secure the camera with the

Lid
Snap
Lock

Mounting Tray Bolt which threads into the camera’s tripod socket,

Diagram B

, page 9.

CAUTION:

Do not cross thread or overtighten the Mounting Tray Bolt as you may
damage the camera tripod socket threads.

8

STEP 3 - Attach Camera to Mounting Tray - continued

Diagram B

SONY

* Control Wheel “cut away.” When not
in use, rotate Control Wheel knob
white dot to the 6 o’clock position so
“cut away” is over camera dial and
not contacting camera.

ZEISS

Mounting Tray

Mounting Tray Bolt

9

SONY

ZEISS

STEP 4 - Attach the Control Ring Gear

The supplied Control Ring Gear is attached to the camera control ring by

3 small nylon Allen Set Screws. Place the Control Ring Gear over the
camera’s step ring before installing the camera in the housing. The Gear
is a “press fit” over the lens. Gently tighten all three allen screws with
the supplied Allen Wrench as show below. DO NOT overtighten or you
may damage the gear, or cause it to warp and bow out from the lens
Control Ring. Make sure to test it’s function once installed.

When installing the camera in the housing, make sure that the Control

Ring Gear meshes properly with the smaller black housing gear.
When removing the Gear, leave the Set Screws in the Gear. The Set
Screws are very small and easy to lose. Extra Set Screws are included
with your housing. We recommend that you leave the Gear installed as
it makes rotating the camera control ring easier when out of the housing.

Control Ring Gear

(properly installed)

Set Screw

10

Turn clockwise to tighten. DO NOT overtighten
or you may warp or damage the gear.

Allen
Wrench

STEP 5 - Installing Camera in the Housing

1. Pull out on each housing control until it stops. This will get the controls
out of the way for installation of the camera.

2. Remove camera lanyard from camera if attached.

3. Place the Housing Front face down in your lap.

4. Extend the built-in camera flash before placing camera in housing.

5. Gently guide the Housing Back with camera attached into the Housing

Front at a slight angle so the Control Ring Gear and Housing Gear
engage properly. Visually check to see that the Gears are properly

engaged.

CAUTION: DO NOT allow the flash to bump into the housing’s main
o-ring sealing surface or the housing top during installation. This could
cause the flash to be damaged or not extend properly in the housing.

STEP 6 - Closing the Housing

1. Once the back is properly

installed, the o-ring should touch
the housing all the way around.
There should be an even gap on
each side of the housing between
the housing and the back.

2. Lift the lid snaps so they are

extended and place each lid snap
into the corresponding hook on
the housing back.

3. To close the housing, push down on

the opposing lid snaps simultaneously

Even gap on
all four sides

Lid Hook

Housing Back

Lid
Snap

Lid Snap Lock

O-ring

until they snap into place. Be sure
they are down far enough to engage
the Lid Snap Lock. The o-ring seal
should now appear as a solid black
line from the back of the housing.

11

STEP 7 - Final Check

The clear housing permits instant visual inspection of the camera and
sealing surfaces as well as complete monitoring of controls and camera
LCD screens. This housing has been factory water pressure tested to
200 ft (60 m).

Once the housing is closed, recheck the o-ring seal. Double check the
gap between the housing back and the housing. It should be even all the
way around the housing.
Look through the clear plastic back at the o-ring. You should see a
darkened area or solid black line where the o-ring is compressed against
the housing back. If you do not see an even black compression seal all
the way around the back, open the lid snaps, reseat the housing back and
close the lid snaps. Visually check the seal again.

Usage

Turn the camera on and operate each of the housing controls to assure
proper functioning. Take a few test shots on land. Make sure the Flash
Diffuser is installed when using only the built-in camera flash, or install
the Flash Deflector when using external strobes, Page 15.

Zoom Control Use

After you have used the housing's
zoom control, it must be returned to the
center position to disengage. If the
housing zoom control i
zoom lever in either direction, you may
not be able to take a picture or access

s pushing the

-

+

-

+

other functions. This is because the
camera is receiving a signal from the
engaged zoom control.

12

Zoom Control
“Disengaged”

(Center Position)

Zoom Control

“Engaged”

Built-in Flash and Strobe Use

Always install the Flash Deflector when using external strobes, Page 14.

Always remove the Deflector and install the Flash Diffuser when using
only the built-in flash, Page 14, 15.

Strobe Use

The optional AF35 strobe triggers and provides automatic TTL exposure
by watching the camera's built-in flash, without the need of fiber optic
cords or sensors. Alternatively, two ports are provided on the front of the
housing for the connection of up to two Ikelite, SEA&SEA, or Olympus
type fiber optic cords.

An included flash diffuser improves lighting quality when the camera's
built-in flash is used. The built-in flash is effective between 1-3 feet
(0.3-0.9m) from the subject in clear conditions. For best results, a color
correcting filter or external lighting is recommended. External lighting is
more powerful and can be placed in a position to virtually eliminate the
backscatter or "snow" from your underwater images.

Using Strobes with a Fiber Optic Connection

Two ports on the front of the housing above the lens port are provided
for the connection of up to two Ikelite, SEA&SEA, or Olympus-type fiber
optic cords. The housing's built-in TTL circuitry will not be operable when
external strobes are attached via fiber optic cord.

Always install the Flash Deflector when using external strobes, Page 14.

13

Using the Camera’s Built-in Flash

If you are shooting with the camera’s built-in flash and the camera lens
is set to the widest angle setting, you may need to zoom the lens slightly
or a dark area may appear in a lower corner of close-up photographs.
The lens port may block some of the light. Install the Diffuser, page 15,
and zoom in to eliminate any dark areas noted in your photographs (You
can test this above water).
For the best results, we recommend using external Strobes.
The camera’s built-in flash CANNOT be used with optional Wide Angle or
Accessory lenses.

Deflector Installation and Removal

The factory installed flash Deflector should be removed and replaced by
the Diffuser, page 15, when using ONLY the built-in camera flash and no
external strobes. To remove, lift the bottom of the Deflector with your
thumb, or a Pen or Pencil tip to loosen and pull the Deflector away from
the inside front of the housing. To install, line up the corresponding
Velcro dots on the housing front with the Deflector Back and press the
Deflector into its factory installed position next to the lens port. If
positioned properly, the small deflector holes will line up with the Fiber
Optic Port holes.

Deflector Back (view from inside housing)

Deflector Holes

Deflector Back (view from outside housing)

Velcro

Bottom of Deflector

14

Diffuser Purpose

When using the built-in camera flash and shooting close-up photographs,

the lens port on the housing can block a portion of the light from the
built-in camera flash. This can result in a shadow in a lower corner of the
picture frame. The Diffuser will help eliminate the shadow. In addition,
you can zoom in if necessary.

Diffuser Installation and Removal

The included Diffuser should only be used when shooting with the
built-in camera flash. A

lways remove the Deflector before using ONLY

the built-in camera flash with a Diffuser.

To install the diffuser, push the “Cut-out Section” into the Port Groove
until it stops as shown. To remove, grab the top of the Diffuser and pull
away from the port.

Note the Small Hole. To avoid losing the diffuser, you can attach a

fishing line or string to this hole.

Diffuser

Cut-out
Section

Small hole

Diffuser properly
installed in Port Groove

15

Entering the Water

As soon as you enter the water, take a moment and check to see that

the housing is properly sealed. We recommend you first water test the
housing with no camera inside to assure a safe and watertight
environment.
Next, check to see if there are any bubbles on the face of the lens port.
If there are, take your finger and remove them. If there are bubbles on
the lens port they can produce soft focus spots in your photos or video.

Recommended Accessories

External Color Correcting Filters

The specially formulated UR/Pro color
correcting filter for tropical blue water settings
enhances warm reds and oranges with
available sunlight up to 80 ft (24 m). Use in the
Caribbean, Indonesia, and any blue water
setting.
The UR/Pro color correcting filter for green
water enhances contrast and improves the
color of green water to give your subject a rich,
natural tone. Effective with available sunlight up
to 80 ft (24m). Use in most lakes and any green water setting.
The color filters are for available light use only. Not recommended when
using external strobes.

UR-Pro Filter

Lens Port

Optional Tray with Release Handle 9523.61

The optional aluminum tray with release
handle comes with the necessary hardware to
mount to your Ikelite housing. To attach, see

page 17.

16

Attach Optional Tray + Dual Handles to Housing

Attaching an optional Tray + Dual Handles will
add stability and gripping point(s) for
comfortable use of the housing. Add a second
strobe to eliminate shadows and evenly light
your subjects.

Attach Optional Tray with Release Handle(s) to Housing

1. Place the housing upside

down on a flat surface or in
your lap so that the housing
port is facing toward you as
shown.

2. Line up the 3/8” tray holes

with the housing mounts. If
the tray is positioned
properly, the handle will be

n your left side facing down.

o

3. Place a shoulder washer in

each 3/8” tray hole with the
small end of the washer facing down.

4. With your free hand, insert and rotate the 12-24 x 1/2” screws clockwise

until threaded into the housing mounts. Finish tightening the tray to the
housing using a flathead screwdriver. Do not overtighten.

17

Attach Optional Strobe Arm to Housing Handle

If you have purchased an optional
Ikelite Tray and Handle for your
housing, an Ikelite Strobe Arm will
easily attach to the Handle by
depressing the spring-loaded Handle
Push Button until it stops. Gently slide
the pronged end of the Ikelite Arm into
the hole in the top of the Handle as

Ikelite Arm

shown.
When the Ikelite Arm is properly
seated, the Handle Push Button will
return to it’s starting position.

AF35 Strobe Package 4035

The AutoFlash AF35 kit is a great
compliment, and an effortless, affordable way
to add a flash to your new Ikelite point and
shoot camera system. Everything you need
to get started is in the box. Just attach it to

Housing Handle

ndle P

Ha
Button

ush

ikelite

AUTOFLASH

ikelite

35

AF

the bottom of your housing and start taking
pictures!

The AF35 Strobe Package is available to support your housing along
with a full range of accessories. Please visit www.ikelite.com to see
additional information regarding this and other strobe package options.

18

External Accessory Lenses

The housing port is designed to accept 3.0-inch diameter color filters,
and wide angle or macro options with 67mm threads. Light is absorbed
very quickly as it passes through water. A subject will look darker, less
colorful and somewhat grainy when viewed through even a few feet of
water. The addition of a compatible wide angle accessory expands the
camera's field of view underwater, providing the opportunity to get as
close as possible to the subject and reduce the amount of water light
passes through.
We recommend the Ikelite W30 Wide Angle Lens or INON UWL-H100
Wide Angle Lens for excellent edge sharpness with minimal vignetting
(dark shadows in the corners of the image). Vignetting may be eliminated
by either zooming slightly or cropping the image in post-production.

Notes:

The camera’s built-in flash cannot be used with External Accessory
Lenses.

Bayonet mount lenses cannot be used with this housing.

Please visit www.ikelite.com for additional information.

Ikelite 6430 W30 Conversion Lens

19

Recommended Accessories -

continued

Video Lighting

External video lights such as the 2101 Vega Video + Photo Light add
color when using the video/movie mode of your camera. Primary video
lights are specially color balanced to provide natural tones.

Additional Accessories

- 2602.3 Quick Release Handle Kit for GoPro

- Gamma LED Focus/Flashlight

A full range of accessories are available to support your housing. Please
visit www.ikelite.com to see the most current information about
recommended accessories for your housing.

20

Maintenance

Lens Port

Treat the glass in the lens port as a camera lens. After use, rinse and
gently dry the outside lens port to avoid water spotting. To clean, use a
mild soap solution or lens cleaner. It is N
Port for cleaning. Do not rinse the inside the Port.

Do not use alcohol or window cleaner on the Lens Port.

OT necessary to remove the

Lubricant

Ikelite provides silicone lubricant with the housing. We recommend you use
only Ikelite lubricant on Ikelite products. Other brands may cause the main
housing o-ring to swell and not seal properly.
Use only enough lubricant to lightly cover the main housing o-ring or
lubricate a sticky control. Wipe off any excess lubricant with a clean
cloth. Lubricant is not a sealant; it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with proper
sealing.

CAUTION:
Never use spray lubricants as the propellant ingredient can cause
the plastic housing to crack or o-rings to swell.

O-ring Storage

When storing the housing, remove the main housing o-ring. Lightly
lubricate the o-ring until it appears shiny and place in a small resealable
plastic bag. Use only Ikelite lubricant. Place the bag inside the housing
and store until needed.

21

Housing Maintenance

Your Ikelite Digital Housing should be given the same care and attention
as your other photographic equipment. In addition to normal
maintenance, we recommend that the housing be returned to Ikelite
periodically to be checked and pressure tested.

- Do Not leave the camera and housing in direct sunlight for prolonged

periods. Heat may damage the camera.

- Do Not ship the camera in the housing.

- Before using the housing, always check the tightness of the set screw in

each control knob. Check each control gland penetrating the housing to
make sure they are tight. There is a slight chance that either could
vibrate loose during travel.

- Keep the main housing o-ring clean and lightly lubricated. To lubricate,

remove the o-ring from the back. Put a small amount of lkelite lubricant
on your fingers. Pull the o-ring through your fingers to apply a thin
coating of lubricant. Only apply enough lubricant to make the o-ring feel
slick. Do Not stretch the o-ring. This light coating of lubricant will help
to keep the o-ring from drying out and will help to show a dark sealing
line when the housing back is properly sealed.

- Keep the area where the o-ring fits and the sealing surface of the

housing clean.

- Rinse the housing exterior thoroughly in fresh water after each saltwater

use. Depress push buttons repeatedly in fresh water to eliminate trapped
saltwater. Dry with a soft cloth. Dry lens port to eliminate water spotting.
After several uses in saltwater, soak the housing exterior in a mild soap
solution; rinse and dry before storing. When storing the housing, remove
the back o-ring, lightly lubricate, and place in a plastic bag. Place the
plastic bag with o-ring inside the housing for safe keeping.

- If removing a housing push button, Do Not re-use the E-clip. Contact

Ikelite for replacement E-clips (part 0319.12).

- Leave lid snaps in the open position when not using the housing for

extended periods.

22

Control Maintenance

Ikelite controls are designed to provide years of reliable service with
minimal maintenance.

- Push button controls normally require no maintenance other than rinsing

in freshwater after saltwater use. Depress each push button in fresh
water several times to eliminate trapped saltwater. If a push button
control becomes difficult to push or if it sticks when depressed, soak the
housing in luke warm fresh water. After a few minutes, operate the push
button. If this does not correct the problem, return the housing to Ikelite
for maintenance. If you are on a trip and unable to return the housing
immediately, a push button may be lubricated by pressing and holding
the push button all the way in. Then, use your finger or other small
non-metal object to place a small amount of lube at the base of the shaft
inside the housing. Press and release the push button several times until
the lube is worked up into the o-ring.

After completing this procedure, close

the housing and submerge it in water
without the camera i nside. Check the
control for watertightness.

Diagram E

Apply Ikelite Lube here

23

Control Maintenance -

continued

In the unlikely event one of the larger gland style control shafts sticks or
becomes difficult to operate, you can remove the control from the
housing and lubricate it, or return the housing to Ikelite for maintenance.
To remove the control, Diagram F, loosen the set screw in the knob
(allen wrench required); remove the knob. If there is salt or dirt build-up
on the exposed c

ontrol shaft, clean the shaft. Open the housing and
gently slide the control shaft out of the control gland. Clean and lightly
lubricate the shaft, including the end of the shaft.

Slide the shaft back into the control gland and gently slide it back and
forth a few times without fully removing the shaft from the gland.
Replace the knob, noting the flat area on the shaft. The set screw in the
knob should tighten down against the flat area on the control so the
knob does not turn on the shaft.
After completing this procedure, close the housing and submerge it in
water without the camera inside. Check the control for watertightness.

Diagram F

Housing

Gland

Control Shaft

Tighten set screw down

against this flat area

when replacing the knob.

24

Lubricate end of shaft
before reinserting into
gland

Loosen set screw
(allen wrench supplied)

Photo Tips

- The number one rule in underwater photography is to eliminate as much
water between the camera and subject as possible. Get as close as you
can to the subject, then use the zoom. If you are using flash for still
photos, subjects beyond 6 ft (1.8 m) will not have much color regardless
of strobe power.

- Photograph in clear water; do not stir up the sand or silty bottom. If
backscatter becomes a problem in the environment you are
photographing, an external flash will help eliminate much of the
backscatter.

- Many digital cameras have a slight lag time between when you press
the shutter release button and the camera actually takes the picture.
Hold the housing steady a second or two after pressing the shutter
release button.

- Do not shoot down on subjects as they will quite often blend into the
background and be difficult to see in the photograph. Shoot subjects
straight on or shoot up at a slight angle using the blue water as a
contrasting background.

- When using daylight or flash, if your camera consistently over or
underexposes the image, you may want to adjust your camera’s
exposure compensation or flash exp. comp. settings.

- If you error in exposure, it is better to have the image slightly
underexposed rather than overexposed. An overexposed image is
missing color information which cannot be adjusted in a photo
processing program. A slightly underexposed image has color
information that can be adjusted.

- It is important to respect all living creatures underwater, including
people, marine life, and coral. While we encourage people to get close
to their subjects when taking a photograph, they should not touch, lie on,
or in any way disturb the things they find underwater.

25

Troubleshooting

Problem

Push buttons or
controls are sticky or
hard to operate

Solution

- Remove the camera and rinse the closed housing
in fresh water. Vigorously press each push button
in and out several times to release any trapped
saltwater or debris.

- Press a sticky push button all the way in and
place a small amount of lube on the small end of
the push button shaft at it’s base. Release and
operate the push button several times to distribute
the lube, Diagram E, page 23.

- If a larger gland style control is sticky, grab the

control knob, pull it out, and then push back in. If
still sticky, see the Control Maintenance section,

Image is
over/underexposed,
or a corner of the
image is dark

Diagram F, page 24.

- Return housing to Ikelite for routine maintenance.

- Check that the built-in flash or external strobe is
firing when taking a picture. Camera flash should
be forced “on.”

- When using an external strobe, make sure it is
turned on, set properly, and its battery is charged.

- Make sure the diffuser is installed when you are
NOT using an external strobe.

- Check any corded connectio

- Change camera shutter speed or aperture.

- Move closer to or further away from the subject.

- Adjust Flash Exposure Compensation .

n p

oints.

- For extreme overexposure turn on the ND neutral

26

density filter.

Problem

Solution

Camera does not
take a picture

Housing is hard to
close

- Install a fully charged battery.

- There is not enough available light for the camera
to properly focus. Add a focusing light or strobe
with a built-in focusing or video light to your

system.

- Select a center focus point in your camera menu.

- Return Zoom control to the “disengaged” p

osition,

see Zoom Control Use, page 12.

- Make sure the camera is mounted properly in the
housing and controls are out of the way.

- Main housing o-ring i

s not seated properly.

- Hotshoe cord is in the way.

- Step Ring is not engaging housing gear properly.

Fogging occurs on
the Lens Port

- Humid air is trapped inside the housing.
The camera produces heat and may condense
any trapped moisture forming fog on the lens port.
Close the housing in an air-conditioned room or
vehicle, or in front of an air-conditioner.

- The housing should not be in direct sunlight for an
extended period of time.

- Purchase desiccant packs also known as
moisture munchers from a local camera store.
Place one or two new packs in your housing
before each day of diving.

- If moisture or water droplets are present around
the controls or sealing areas, return the housing
to Ikelite for evaluation.

- Clean the main housing o-ring and sealing
surface of the housing.

27

Problem

Solution

Water enters the
housing

Pictures are too blue
or too green

- Remove, clean and properly lubricate the main
o-ring.

- Look for hair, dirt, or foreign debris crossing the
o-ring seal.

- Reassemble the housing without a camera
installed and immerse in water.

- Return housing to Ikelite for evaluation.

- Use custom (manual) white balance. Reset for
each working depth or when attaching a
color correcting filter to the camera lens.

- Add an external strobe.

- Move in closer to your subject when taking a
picture.

- Add an optional color correcting filter to the
Housing Port.

28

Spare Parts

- 0184.2 Silicone Lubricant 2cc Reclosable Tube

- 0119.2 Port o-ring

- 0200 Port cover

- 0109 Main o-ring

- 9523.10 Tray Hardware

- 0945.18 Allen Wrench for control knobs

- 0945.11 Allen Wrench for Control Ring small nylon set screws

Control Ring small nylon set screws and allen wrench

(available through Ikelite or any Ikelite Dealer)

29

Customer Support

Please read the troubleshooting section of this instruction manual before
contacting Ikelite Customer Support.

Ikelite Underwater Systems
Service Department
50 West 33rd St.
Indianapolis, IN 46208 USA

Email: [e-mail]
Phone: [phone]

Limited Warranty

This Ikelite product is warranted against any manufacturing defects for a
period of one (1) year from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return to customer
postage paid. All other claims of any nature are not covered. Except as
mentioned above, no other warranty expressed or implied applies to this
Ikelite product.

30

Returning Products For Service

Ikelite is most interested in performing any service to ensure that all
products perform as intended. Evidence of purchase date must be
provided to obtain warranty service.
No prior authorization is required. You may return directly to us or
through your dealer. Please include a brief description of the problem,
any relevant email correspondence, and/or instructions on what you
want us to do. Always include name, shipping address, email address,
and phone number inside of the package. Send postage paid to:

Ikelite Underwater Systems
Attention: Service Department
50 West 33 Street
Indianapolis, IN 46208 USA

No reimbursements for postage paid will be issued.

You may also want to insure the package.

Returning Products for Service -

For the separate international customs documentation form that you
complete to accompany the shipment, please state or designate that the
enclosed products were originally manufactured in the USA and are
being returned to the manufacturer for repair service. Value of the

outside the United States

equipment listed for customs purposes should be zero.

31

Product Registration

Please go to www.ikelite.com to register your Ikelite housing within 15
days of purchase.

Ikelite Underwater Systems

50 West 33rd Street

Indianapolis, IN 46208 USA

www.ikelite.com

© 2014 Ikelite Underwater Systems

6116.12_Sony_RX100III_01-0714