TRÅDFRI
ENGLISH
4
FRANÇAIS
ESPAÑOL
10
16
ENGLISH 4
REMOTE CONTROL FUNCTIONS
ON/OFF: Press to turn your light
source on and off.
Press and hold for at least 3 seconds
to synchronize your lights.
Dim u p/dow n : Short presses will
dim up/down in steps. To dim up/down
seamlessly, press and hold the button.
Change white spectrum, colours or
scenes.
Pairing: Add IKEA Smart Lighting
products to your system. See
instructions below.
ADDING DEVICES TO YOUR
REMOTE CONTROL
When the remote control is sold together
with a light source (in the same package),
they are already paired. If the remote
control is purchased separately, you must
manually pair it to your light source.
To add light sources, just repeat the steps
below.
1. Make sure that your light source is
installed and the main power switch is
turned on.
2. Hold the remote control close to the
light source you want to add (no more
than 5 cm away).
3. Press and hold the pairing button
for at least 10 seconds. A red light will
shine steadily on the remote control.
Your light source will begin to dim and
ash one time to indicate that it has
been successfully paired.
Up to 10 light sources can be paired with 1
remote control.
Make sure to pair them one at a time. If
the light sources are close to each other,
disconnect those that have already been
paired from the main power switch.
5
REMOVING DEVICES FROM YOUR
REMOTE CONTROL
1. Make sure the main power switch is
turned on for the light source you want
to un-pair from your TRÅDFRI remote
control.
2. Hold the remote control close to the
light source you want to remove (no
more than 5 cm away).
3. Press and hold the pairing button
for at least 10 seconds. A red light will
shine steadily on the steering device.
Your light source will begin to dim and
ash twice to indicate that it has been
successfully un-paired.
FACTORY RESET YOUR DEVICES
For light sources:
Toggle the main switch 6 times.
For remote control:
Press the pairing button 4 times within
5 seconds.
SYNCHRONIZING
If your light source becomes
unsynchronized, press and hold the ON/
OFF button for at least 3 seconds to
return the light source to its default
setting (100% brightness, 2700K).
CHANGING THE BATTERY
When the remote control is used regularly
and as intended, the batteries will last for
approximately 2 years.
When it’s time to replace the battery, a
red LED indicator will ash when you press
any button on the remote control.
Open the battery lid and replace the
battery with a new CR2032 battery.
CAUTION!
Risk of explosion if battery is replaced
by an incorrect type. Dispose of used
batteries according to the instructions.
6
IMPORTANT!
The remote control is for indoor use only
and can be used in temperatures ranging
from 0ºC to 40 ºC.
Do not leave the remote control in direct
sunlight or near any heat source, as it may
overheat.
Do not subject the remote control to wet,
moist or excessively dusty environments
as this may cause damage.
The range between the remote control
and the receiver are measured in open air.
Different building materials and placement
of the units can affect the wireless
connectivity range.
CARE INSTRUCTIONS
To clean the remote control, wipe with
a soft cloth moistened with a little mild
detergent. Use another soft, dry cloth to
wipe dry.
NOTE!
Never use abrasive cleaners or chemical
solvents as this can damage the product.
TECHNIC AL DATA
Type: E1524 TRÅDFRI Remote
Input: 3V, CR2032 Battery
Range: 10 m in open air.
For indoor use only
Operating frequency: 2405-2480Mhz
Output power: 14 dBm
Manufacturer: IKEA of Sweden AB
Address: Box 702, 343 81 ÄLMHULT
7
This device complies with Part 15 of the
FCC Rules/Industry Canada licence-exempt
RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation of
the device.
WARNING:
Any changes or modications to this unit
not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
— This equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the quipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
8
RF EXPOSURE INFORMATION
This product is approved as a portable
handheld device (not body worn)
This product includes a static magnet,
generating a magnetic eld that might
interfere with the normal operation of
pacemakers, debrillators, or other medical
devices.
Maintain a safe distance of separation
between your medical device and this
device. Stop using this device and
consult your physician or medical device
manufacturer if you believe that it is
interfering with your medical device.
License rights and limitations
NO RIGHTS OR LICENSES, EXPRESS
NO RIGHTS OR LICENSES, EXPRESS
OR IMPLIED, ARE GRANTED TO USE
THIRD-PARTY DEVICES IN COMBINATION
WITH THESE PRODUCTS IN A WIRELESS
MESH NETWORK, OR TO USE THIRDPARTY SERVICES TO ACCESS, MONITOR
OR CONTROL THESE PRODUCTS IN A
WIRELESS MESH NEWORK VIA THE
INTERNET OR ANOTHER EXTERNAL WIDE
AREA NETWORK.
For use pursuant to U.S. Patent Nos.:
US 6,914,893
US 7,697,492
US 8,964,708
Loading...