Ikea Tradfri User Manual
TRÅDFRI
English 4
Français 8
Español 12
4English
WIRELESS SIGNAL REPEATER
FUNCTIONS
With TRÅDFRI signal repeater you can
expand the signal reach of your IKEA
Home smart products.
Pairing: Add IKEA Home smart
products to your system. See
instructions below.
ADDING STEERING DEVICE TO
YOUR SIGNAL REPEATER
When the Signal Repeater is sold
together with another IKEA Home smart
product (in the same package), they are
already paired.
You cannot add IKEA Home smart
products directly to your signal
repeater. A TRÅDFRI steering device is
needed to add them.
To add steering devices, just follow the
steps below:
Make sure that your signal repeater
is plugged in and the main power is
turned on.
1. Hold the steering device close to the
signal repeater you want to add (no
more than 5 cm away).
2. Press and hold the pairing button for
at least 10 seconds , you can nd the
pairing button under the rear cover.
3. A red light will shine steadily on the
steering device.
Then go to the product you want to
steer and then repeat the pairing.
On your IKEA Home smart products a
white light will begin to dim and ash
one time to indicate that it has been
successfully paired.
FACTORY RESET YOUR DEVICE
For wireless signal repeater:
Push a pin into the pinhole on bottom
of the signal repeater for at least 5
seconds.
After reset the signal repeater you must
pair your steering device to the signal
repeater and then pair the steering
device to your IKEA Home smart product
product again.
IMPORTANT!
• The Signal Repeater is for indoor use
only and can be used in temperatures
ranging from 0ºC to 40 ºC
(32ºF to 104 ºF).
• Do not leave the wireless Signal
Repeater in direct sunlight or near any
heat source, as it may overheat.
• The range between the wireless
Signal Repeater and the receiver
are measured in open air. Dierent
building materials and placement
of the units can aect the wireless
connectivity range.
5
WARNING:
• The wall socket must be located near
the equipment and must be easily
accessible.
• Only use in dry locations.
• Children should be supervised to
ensure they do not play with the
product.
• If the device is damaged it shall be
destroyed.
• Never use a damage or faulty USB
cable for charging, since this can
damage the appliance and harm your
device.
TECHNICAL DATA
Type: E1746 wireless Signal Repeater
Input: 5.0V DC
Range: 10 m in open air
For indoor use only
Operating frequency: 2405-2480Mhz
Output power: 3 dBm
Instructions for use
• Connect the power adapter into the
wall socket, insert the Signal Repeater
into the free slot.
• When charging only use a
recommended USB cable for your
device and replace faulty cables
imminently.
Good to know
• Can be used to charge the wireless
roller blind battery-cell.
• USB cable length and quality
inuences charging speed and
performance.
• Devices may get warm during
charging; this is completely normal
and they will gradually cool down
again after they are fully charged.
• Storage temperature: -20°C to 25°C
(4°F to 77°F).
• Operating temperature: 0°C to 40°C
(32°F to 104°F).
• Unplug the power adapter from the
power source before cleaning and
when it is not in use.
Recommended precautionary measures
and technical data, see the back of the
power adapter.
CARE INSTRUCTIONS
To clean the Signal Repeater and the
Power Adapter wipe with a soft dry cloth.
NOTE!
Never use abrasive cleaners or chemical
solvents as this can damage the
product.
Save these instructions for
future use.
Product servicing
Do not attempt to repair this product
yourself, as opening or removing covers
may expose you to dangerous voltage
points or other risks.
Loading...