Ikea IHI75UC6FS Use & Care Guide

36" (91.4 CM) ISLAND-MOUNT

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONL IMPOR SÓLO P IMPOR POUR UTILISA

CANOPY RANGE HOOD

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-866-644-2449.

In Canada, for assistance, installation and service, call: 1-866-664-2449.

CAMPANA DE COCINA PARA ISLA CON

ESCUDETE DE 36" (91,4 CM)

Instrucciones de instalación y Manual de uso y cuidado

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico,

llame al: 1-866-664-2449.

HOTTE DE CUISINIÈRE CONFIGURÉE

EN ÎLOT DE 36" (91,4 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer le 1-866-664-2449.

Table of Contents/Índice/Table des matières ...........................2

For warranty concerns, do not take the appliance back to the store. Please contact us in U.S.A. or Canada at 1-866-664-2449. This product features a Limited Warranty - See the “Warranty” section for complete details. IKEA® appliances carry a 5-year warranty

(excludes LAGAN family - see warranty for coverage details). NOTE: Proof of Purchase is required to obtain warranty service.

Si tiene dudas acerca de la garantía, no devuelva el aparato a la tienda. Póngase en contacto con nosotros en los EE.UU. o en Canadá al 1-866-664-2449.

Este producto tiene una garantía limitada - Consulte la sección “Garantía” para obtener todos los detalles. Los aparatos IKEA® tienen una garantía de 5-años (excluyendo los de la familia LAGAN - consulte la garantía para ver los detalles acerca de la cobertura).

NOTA: Se requiere la prueba de compra para obtener servicio bajo la garantía.

Pour toute question concernant l’application de la garantie, ne pas rapporter l’appareil au magasin. Veuillez nous contacter aux É.-U. ou au Canada au 1-866-664-2449.

Ce produit est couvert par une garantie limitée – Voir la section “Garantie” pour des détails complets. Les appareils IKEA® sont couverts par une garantie de 5-ans (hormis les appareils de la série LAGAN - voir la garantie pour des détails concernant les modalités de garantie).

REMARQUE : Une preuve d’achat est obligatoire pour obtenir l'application de la garantie.

TANTE: LEA Y GUARDE ESTAS INSTRUCCIONES.

ARA USO RESIDENCIAL.

TANT : LIRE ET CONSERVER CES INSTRUCTIONS.

TION RÉSIDENTIELLE UNIQUEMENT

LIB0119520B/W10836371C

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS .................................................5

Tools and Parts .............................................................................5

Location Requirements ................................................................5

Venting Requirements ..................................................................6

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS ...................................................8

Prepare Location ..........................................................................8

Assemble Range Hood ................................................................9

Install Range Hood .......................................................................9

Make Electrical Connection .......................................................10

Install Duct Covers .....................................................................11

Complete Installation .................................................................12

ÍNDICE

SEGURIDAD DE LA CAMPANA PARA COCINA ........................19

REQUISITOS DE INSTALACIÓN .................................................21

Herramientas y piezas ................................................................21

Requisitos de ubicación .............................................................21

Requisitos de ventilación ...........................................................22

Requisitos eléctricos ..................................................................24

INSTRUCCIONES DE INSTALACIÓN .........................................24

Prepare la ubicación ..................................................................24

Ensamble la campana para cocina............................................25

Instalación de la campana para cocina .....................................26

Haga la conexión del suministro eléctrico .................................27

RANGE HOOD USE ......................................................................13

Range Hood Controls ................................................................13

RANGE HOOD CARE ...................................................................14

Cleaning .....................................................................................14

WIRING DIAGRAM .......................................................................15

ASSISTANCE OR SERVICE .........................................................16

In the U.S.A. ...............................................................................16

In Canada ...................................................................................16

Accessories ................................................................................16

WARRANTY ..................................................................................17

Instalación de las cubiertas del ducto .......................................28

Completar la instalación ............................................................29

USO DE LA CAMPANA DE COCINA ..........................................30

Controles de la campana para cocina .......................................30

CUIDADO DE LA CAMPANA DE COCINA .................................31

Limpieza ....................................................................................31

DIAGRAMA DE CABLEADO ........................................................32

AYUDA O SERVICIO TÉCNICO ...................................................33

En los EE.UU. .............................................................................33

Accesorios ..................................................................................33

GARANTÍA.....................................................................................34

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................36

EXIGENCES D’INSTALLATION ...................................................38

Outils et pièces ...........................................................................38

Exigences d’emplacement .........................................................38

Exigences concernant l’évacuation ...........................................39

Spéciﬁcations électriques ..........................................................40

INSTRUCTIONS D’INSTALLATION .............................................41

Préparation de l’emplacement ...................................................41

Assemblage de la hotte .............................................................42

Installation de la hotte ................................................................42

Raccordement électrique ...........................................................43

Installation des cache-conduits .................................................44

Achever l’installation ..................................................................45

UTILISATION DE LA HOTTE .......................................................46

Commandes de la hotte de cuisinière .......................................46

ENTRETIEN DE LA HOTTE .........................................................47

Nettoyage ...................................................................................47

SCHÉMA DE CÂBLAGE ...............................................................48

ASSISTANCE OU SERVICE .........................................................49

Au Canada ..................................................................................49

Accessoires ................................................................................49

GARANTIE .....................................................................................50

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

■ Level

■ Drill with 1

and 7/64" (2.75 mm) drill bits

■ Pilot hole drill bits (determined by chimney support

attachment method)

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

Parts Needed

■ Home power supply cable

■

/2" (12.7 mm) UL listed or CSA approved strain relief

■ 3 UL listed wire connectors

For Vented Installations, You Will Also Need:

■ 1 wall or roof cap

■ Metal vent system

For Non-Vented (Recirculating) Installations, You Will Also Need:

■ Charcoal Filter Kit Part Number W10412939 for non-vented

(recirculating) installations only. See “Assistance or Service” section to order.

■ 6" (15.2 cm) diameter round metal vent duct -

length required is determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

■ Hood ventilator assembly with canopy glass, retainer

brackets, rubber seals, and LED lights installed

■ Vent transition with backdraft damper installed

■ Metal grease ﬁlter

■ Mounting template

■ 2 - Upper vent covers

■ 2 - Lower vent covers

■ 4 - Plastic vent clips

■ Upper horizontal support bracket

■ Horizontal support

■ 8 - Vertical supports

■ 2 - 2.9 x 3 mm screws (T10 drive)

■ 4 - 3.5 x 6.5 mm screws (T10 drive)

/4" (3.2 cm), 3/8" (9.5 mm), 1/8" (3.2 mm),

■ 2 - 3.5 x 9.5 mm mounting screws (Phillips)

■ 62 - 4.2 x 8 mm screws (T20

■ 4 - 5 x 45 mm mounting screws (#2 Phillips drive)

■ Air deﬂector (for non-vented/recirculating installation)

■ T10 Torx

■ T20

®†

adapter

Torx® adapter

®†

drive)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Have a qualiﬁed technician install the range hood. It is the

installer’s responsibility to comply with installation clearances speciﬁed on the model/serial/rating plate. The model/serial/ rating plate is located behind the left ﬁlter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as windows, doors, and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

Because of the size and weight of this island hood, the chimney support must be securely attached to the ceiling.

■ For plaster or drywall ceilings, the chimney support must

be attached to joists. If this is not possible, you must build a support structure behind the plaster or drywall. The support structure must be able to support 80 lbs (36.6 kg).

This range hood is recommended for use with cooktops with a maximum total rating of 60,000 BTUs or less.

The range hood is factory set for venting through the roof or wall. For non-vented (recirculating) Installation see “Non-vented

(recirculating) Installation” in “Install Range Hood” section. Charcoal Filter Kit Part Number W10412939 is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A or latest edition, or with local codes.

†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Product Dimensions

The chimneys can be adjusted for different ceiling heights. See the following chart.

A. 121/4" (31.1 cm)

B. 13

/16" (33.5 cm)

C. *29

/4" (75.6 cm) min. 4413/16" (113.8 cm) max.

**293/4" (75.6 cm) min. 4913/16" (126.5 cm) max.

D. 3

/2" (8.9 cm)

E. 36" (91.4 cm)

F. 25

/16" (64 cm)

* Vented installations only ** Non-vented (recirculating) installations only

Installation Dimensions

A. Countertop height B. Hood height from ceiling to bottom

of the range hood ﬁlter surface: D-A-C=B

C. Hood height: 24" (61 cm) min. from electric

cooking surface, 27" (68.6 cm) min. from gas cooking surface, suggested 36" (91.4 cm) max.

D. Ceiling height

IMPORTANT:

Minimum distance “C”: 24" (61 cm) from electric cooking surface, 27" (68.6 cm) from gas cooking surface

Suggested maximum distance “C”: 36" (91.4 cm)

Vented Installations

Min. ceiling height Max. ceiling height

Electric cooking

7' 8" (2.34 m) 9' 10" (3 m)

surface Gas cooking

7' 11" (2.41 m) 9' 10" (3 m)

surface

Non-Vented (Recirculating) Installations

Min. ceiling height Max. ceiling height

Electric cooking

7' 8" (2.34 m) 10' 3" (3.12 m)

surface Gas cooking

7' 11" (2.41 m) 10' 3" (3.12 m)

surface

NOTE: The range hood chimneys are adjustable and designed to meet varying ceiling or sofﬁt heights depending on the distance “C” between the bottom of the range hood and the cooking surface. For higher ceilings, a Stainless Steel Chimney Extension Kit Part Number EXTKIT26FS is available from your dealer or an authorized parts distributor. The chimney extension replaces the upper chimney shipped with the range hood.

Venting Requirements

■ Vent system must terminate to the outdoors except

for non-vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use 4" (10.2 cm) laundry-type wall cap.

■ Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■ The vent system must have a damper. If the roof

or wall cap has a damper, do not use the damper supplied with the range hood.

For the Most Efﬁcient and Quiet Operation:

■ Use a straight run or as few elbows as possible.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening

around the cap.

■ The size of the vent should be uniform.

Cold Weather Installations

An additional backdraft damper should be installed to minimize backward cold air ﬂow and a thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

Makeup Air

90 elbo

Wall cap

Local building codes may require the use of makeup air systems when using ventilation systems greater than speciﬁed CFM of air movement. The speciﬁed CFM varies from locale to locale. Consult your HVAC professional for speciﬁc requirements in your area.

Venting Methods

This island hood is factory set for venting through the roof. A 6" (15.2 cm) round vent system is needed for installation

(not included). The hood exhaust opening is 6" (15.2 cm) round. NOTE: Flexible vent is not recommended. Flexible vent

creates back pressure and air turbulence that greatly reduce performance.

Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.

For Non-Vented (Recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the non-vented (recirculating) version, ﬁtting a charcoal ﬁlter and the deﬂector. Fumes and vapors are recycled through the top grille. To order, see the “Assistance or Service” section.

Non-Vented (Recirculating)

Roof Venting

A. Deﬂector B. 6" (15.2 cm) round vent

A. Roof cap B. 6" (15.2 cm) round vent

NOTE: If codes permits, wall venting can be an option for 2-story homes.

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft (0.8 m)

Example Vent System

2 ft

(0.6 m)

The following example falls within the maximum recommended vent length of 35 ft (10.7 m).

1 - 90° elbow = 5 ft (1.5 m) 1 - wall cap = 0 ft (0 m) 8 ft (2.4 m) straight = 8 ft (2.4 m) Length of system = 13 ft (3.9 m)

6 ft (1.8 m)

Electrical Requirements

Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

■ A 120-volt, 60 Hz., AC-only, 15-amp, fused electrical

circuit is required.

■ If the house has aluminum wiring, follow the

procedure below:

1. Connect a section of solid copper wire to the

pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as speciﬁed on the model/serial/rating plate. The model/serial/rating plate is located behind the left ﬁlter on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition), and all local codes and ordinances.

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

90° elbow 5 ft (1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

INSTALLATION INSTRUCTIONS

Prepare Location

■ Lay out the vent duct system before installing the range

hood to determine the best routing for the vent duct.

■ It is recommended that the vent system be installed

before the range hood is installed.

■ Before making cutouts, make sure there is proper

clearance within the ceiling for exhaust vent.

■ Range hood is to be installed 24" (61 cm) min.

for electric cooking surfaces, 27" (68.6 cm) min. for gas cooking surfaces, to a suggested maximum of 36" (91.4 cm) above the cooking surface.

■ Remove ﬁlm from metal surfaces as needed prior

to assembly.

■ Check your ceiling height and the range hood height

maximum before you install your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall

or non-vented.

3. Select a ﬂat surface for assembling the range hood.

Place covering over that surface. Place two 3" (7.6 cm) high spacers (not included) onto the covered surface.

NOTE: Cover the spacers to avoid damage to the range hood surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood

onto covered spacers.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the ceiling

where the range hood will be installed, considering the requirements for ceiling support structures. See the “Location Requirements” section. Make sure the range hood is centered over the cooking surface.

2. Tape template in place on the ceiling at the marked

centerline. The line for the front of the range hood should be parallel to the front of the cooktop.

3. Use a pencil to mark the mounting screws, wire access,

and duct hole locations on the ceiling. NOTE: Mounting hole locations should be into a ceiling

support structure capable of holding 80 lbs (36.6 kg). Remove the template.

4. Drill 4 - 3/16" (4.8 mm) pilot holes for mounting the

upper horizontal support.

Complete Preparation

1. Determine the required location for the home power supply

cable and drill a 1/2" (1.3 cm) diameter hole for wire access.

2. Run 1/2" (1.3 cm) conduit and wires or home power supply

cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough 1/2" conduit and wires or home power supply cable from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

3. For vented installations only: Using a jigsaw or keyhole

saw, cut a 61/2" (16.5 cm) diameter hole for the vent duct.

4. Attach the upper horizontal support bracket with

4 - 5 x 45 mm #2 Phillips wood screws. NOTE: Upper horizontal support screws must be into a

ceiling support structure capable of holding 80 lbs (36.6 kg).

A. Covered spacers B. Glass canopy C. Ventilator assembly

A. Upper horizontal support B. 5 x 45 mm screws (#2 Phillips drive)

Assemble Range Hood

1. Install transition on top of hood (if removed for shipping)

with 2 - 3.5 x 9.5 mm Phillips drive sheet metal screws.

4. Attach a second set of vertical supports (A) and set

the vertical height (B). See “Installation Dimensions” in the “Location Requirements” section to help determine the desired dimension for vertical height “B.”

Secure with 16 - 4.2 x 8 mm T20® screws.

A. Vent transition B. 3.5 x 9.5 mm screw

2. Position the 4 vertical supports (A) with the notches

at the bottom and attach to the range hood using 16 - 4.2 x 8 mm T20® screws. Use a T20® Torx® drive (or T20® adapter provided) to tighten all assembly screws.

A. Vertical supports B. Vertical height

Install Range Hood

Non-Vented (recirculating) Installation

1. Attach the air deﬂector to the upper horizontal support

using 2 - 4.2 x 8 mm T20® mounting screws.

A. Vertical supports B. Horizontal support C. Notched end

3. Position the lower horizontal support (B) as shown (ﬂanges

pointed down). Attach to the lower vertical supports using 8 - 4.2 x 8 mm T20® screws. The lower horizontal support can be positioned at any of the three mounting hole locations in the lower vertical supports.

A. Deﬂector B. 2 - 4.2 x 8 mm T20

2. Measure the length of 6" (15.2 cm) duct needed

to connect the transition to the deﬂector. NOTE: Vent should ﬁt up inside the deﬂector

1" (2.5 cm) minimum.

3. Install vent between the transition and the deﬂector. NOTE: To make vent installation easier, temporarily remove

the deﬂector from the chimney support bracket and replace after vent section is in place.

4. Seal all connections with vent clamps. Continue

mounting screws

with “Range Hood Installation” in this section.

Range Hood Installation

A. Vertical supports (4) B. Horizontal support C. Screws 4.2 x 8 mm T20 D. Mounting hole locations for horizontal support

(8)

1. Using 2 or more people, lift the range hood assembly and attach it by snapping the vertical supports to the spring clips in the upper horizontal support bracket that is mounted to the ceiling.

NOTE: The range hood assembly must be held in place while you are installing the screws in the next step.

2. Install 16 - 4.2 x 8 mm T20® screws and tighten to secure.

A. Mounting screws

Connect Vent System

1. Install vent system.

2. Push duct over the exhaust outlet. Seal all connections

with vent clamps.

3. Use caulk to seal all openings.

Make Electrical Connection

WARNING

4. Run home power supply cable through strain relief into terminal box.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Remove terminal box cover using a T10 Torx® drive

(or T10 adapter provided) to remove the screws.

3. Remove the knockout in the terminal box and install

a UL listed or CSA approved 1/2" strain relief.

A. Terminal box B. Knockout C. Terminal box cover

A. Home power supply cable B. UL listed or CSA

approved strain relief

C. Black wires

5. Use UL listed wire connectors and connect black wires (C) together.

6. Use UL listed wire connectors and connect white wires (E) together.

D. UL listed wire connectors E. White wires F. Green (or bare) and

yellow-green ground wires

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire in terminal box.

Failure to do so can result in death or electrical shock.

7. Connect green (or bare) ground wire from home power supply to yellow-green ground wire (F) in terminal box using UL listed wire connectors.

8. Tighten strain relief screw.

9. Install terminal box cover.

10. Check that all light bulbs are secure in their sockets.

11. Reconnect power.

Install Duct Covers

NOTE: Remove the ﬁlm from the duct covers.

1. Assemble the upper duct covers together and install

the duct covers around the support frame. The larger hole in the ﬂanges of the upper duct cover must be outside the smaller hole in the mating ﬂange of the other upper duct cover.

2. Secure the upper duct covers together with two

3.5 x 6.5 mm T10 screws at the top and two 2.9 x 3 mm T10 screws at the bottom. Install 1 screw on each side at the top and bottom of the assembled duct covers.

3. Slide the upper duct covers up the frame to the ceiling and secure to the upper horizontal support with 2 - 3.5 x 6.5 mm T10 screws.

A. 3.5 x 6.5 mm screw B. Slotted holes (2) C. Upper duct covers D. Ceiling

4. Place the long end of the plastic clips (2) into the bottom of the front lower duct cover.

A. 3.5 x 6.5 mm screws (2) B. Assembly holes (larger hole outside

of smaller hole on both sides)

C. 2.9 x 3 mm screws (2)

NOTE: For non-vented (recirculating) installation, the slotted holes in the upper duct covers will be visible when assembled. For vented installations, the slotted holes will be hidden down inside the lower duct covers.

A. Lower duct cover - (front) B. Plastic clips (2) (long end for front placement)

5. Install the lower duct cover (front) to the range hood canopy. Spread the lower duct cover opening slightly and position it over the upper duct cover. Set the lower duct cover in place. Position so the ﬂanges of the lower duct cover set into the ﬂanges of the upper duct covers.

A. Top toward ceiling B. Slots installed up for non-vented installations C. Slots installed down for vented installations

A. Range hood canopy B. Plastic clips C. Lower duct covers D. Upper duct covers

6. Install the lower duct cover (rear) to the range hood canopy.

Spread the lower duct cover opening slightly and position it over the upper duct cover. Set the lower duct cover in place. Position so the ﬂanges of the lower duct cover set into the ﬂanges of the upper duct cover. Make sure the front and rear lower duct covers mate properly.

NOTE: When assembling the rear lower duct cover to the front lower duct cover, the ﬂange (both sides) must be placed over the plastic clip to secure the lower duct covers together at the bottom.

A. Lower duct cover (rear) B. Plastic clips C. Lower duct covers D. Upper duct covers

8. Secure the lower duct cover to the range hood canopy using 4 - 4.2 x 8 mm T20® screws.

Complete Installation

1. For non-vented (recirculating) installations only, install charcoal ﬁlters over metal grease ﬁlter. See the “Range Hood Care” section.

2. Install metal ﬁlters. See the “Range Hood Care” section.

3. Check the operation of the range hood blower and light.

See the “Range Hood Use” section. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

NOTE: To get the most efﬁcient use from your new range hood, read the “Range Hood Use” section.

7. Secure the lower duct covers together at the top using

2 plastic clips. Use one plastic clip on each side.

A. Plastic clips (2) B. Lower duct covers top clip area

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors, and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen.

The hood controls are located on the front side of the canopy.

Range Hood Controls

A. Blower speed maximum button B. Blower speed medium button C. Blower speed minimum button D. Blower Off button E. On/Off LED task light button

A. Louver holes (non-vented

[recirculating] installations only) B. Duct covers C. Control panel D. LED lights

E. Metal grease ﬁlters (located

behind the perimetric cover) F. Perimetric cover G. Glass canopy H. Light switch

(ambient lighting)

Operating the LED task light

The On/Off light button controls both lights. Press once for ON and again for OFF.

Operating the blower

The Blower Speed buttons turn the blower On and control the blower speed and sound level for quiet operation. The speed can be changed anytime during fan operation by pressing the desired Blower Speed button.

The Blower Off button turns the blower Off.

Operating the Ambient Lighting

The switch controls the ambient lighting.

1. Press to the left to turn Auto On.

2. Press to the right to turn Ambient Lighting On.

3. Press to the center to turn Ambient Lighting or Auto Off. NOTE: When the Ambient Lighting is placed in the Auto setting,

a sensor will automatically sense if it is dark in the area around the range hood. The Ambient Lighting will turn on and stay on until it senses there is enough light in the area around the range hood, or the Ambient Lighting switch is placed in the ON or OFF position.

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease ﬁlters frequently according to the following instructions. Replace grease ﬁlters before operating hood.

Exterior Surfaces

To avoid damage to the exterior surface, do not use steel wool or soap-ﬁlled scouring pads.

Always wipe dry to avoid watermarks.

Cleaning Method:

■ Liquid detergent soap and water or all-purpose cleanser

■ Wipe with damp soft cloth or nonabrasive sponge,

and then rinse with clean water and wipe dry.

Metal Grease Filter

1. Open the stainless steel panel. Grasp panel at the left

corners and pull down to disengage the 2 catch pins from the spring catches. The panel is attached at the right and will rotate down.

Non-Vented (recirculating) Installation Filters

The charcoal ﬁlter is not washable. It should last up to 6 months with normal use. Replace with Charcoal Filter Kit Number W10412939.

To replace charcoal ﬁlter:

1. Remove metal grease ﬁlter from range hood.

See “Metal Grease Filter” in this section.

2. Bend spring clips away from metal grease ﬁlter.

3. Place charcoal ﬁlter into top side of metal ﬁlter.

4. Bend spring clips back into place to secure the

charcoal ﬁlter to the metal ﬁlter.

2. Remove the ﬁlter by pulling the spring-release handle

and then pulling down the ﬁlter.

A. Spring-release handle

3. Wash metal ﬁlter as needed in dishwasher or hot

detergent solution.

4. Reinstall the ﬁlter by making sure the spring-release handles

are toward the front. Insert aluminum ﬁlter into upper track.

5. Push in spring-release handle.

6. Push up on metal ﬁlter and release handle to latch into place.

5. Replace metal grease ﬁlter. See “Metal Grease Filter”

in this section.

Replacing a LED Lamp

The LED lights are replaceable by a service technician only. See “Assistance and Service” section for service contact information.

WIRING DIAGRAM

Ambient Light Switch

Function Position

Off

Auto

LNG

POS 1

POS 2

POS 3

Light

Sensor

Tu rns on at 10 LUX

Tu rns off at 50 LUX

Output: 700mA (2 - 15 VDC)

Driver

Input: 120 VAC

Position 3

Position 2

Position 1

Input

Output

YL/GN

RD BK

YL BU

Push Button Switch

Off

Lamps

Operation

No Connection

Blue - Yellow

Brown - White

Brown - Red

Brown - Black

(M - La)

(L - 1)

(L - 2)

(L - 3)

Push Button Switch

21L3MLa

Function Position

Low Speed

Med Speed

High Speed

Motor Specifications

Power Supply

Frequency

Power Absorption

Output: 700mA (2 - 15 VDC)

Input: 120 VAC

Driver

YL/GN

Blue - Black

Blue - Gray

Blue - Red Blue - White Room Temp.

73ºF 23ºC

120 VAC

60 HZ 240 W

28.8

30.3

37.7

45.1

YL/GN

Strip LED

RD BK

WH BK

LED

SE136C

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check to see whether a circuit breaker has tripped or a household fuse has blown. It may save you the cost of a service call. If you still need help, follow the instructions below.

When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you use only factory speciﬁed parts. Factory speciﬁed parts will ﬁt right and work right because they are made with the same precision used to build every new IKEA® appliance.

To locate factory speciﬁed parts in your area, call us or your nearest designated service center.

In Canada

Call the Whirlpool Canada Customer eXperience Centre toll-free:

1-866-664-2449.

Our Consultants Provide Assistance With:

■ Features and speciﬁcations on our full line of appliances.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Referrals to local dealers, repair parts distributors,

and service companies. Whirlpool Canada LP designated service technicians are trained to fulﬁll the product warranty and provide after-warranty service anywhere in Canada.

In the U.S.A.

Call the Whirlpool Customer eXperience Center toll-free:

1-866-664-2449.

Our consultants provide assistance with:

■ Features and speciﬁcations on our full line of appliances.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking,

hearing impaired, limited vision, etc.).

■ Referrals to local dealers, repair parts distributors,

and service companies. Whirlpool designated service technicians are trained to fulﬁll the product warranty and provide after-warranty service anywhere in the United States.

For further assistance

If you need further assistance, you can write to Whirlpool Corporation with any questions or concerns at:

IKEA Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

For Further Assistance

If you need further assistance, you can write to Whirlpool Canada with any questions or concerns at:

Customer eXperience Centre Whirlpool Canada LP 200 - 6750 Century Ave. Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Charcoal Filter Kit

(for non-vented installations only) Order Part Number W10412939

Chimney Extension Kit

Order Part Number EXTKIT26FS

6" (15.2 cm) Makeup Air Kit

(consult local building codes) Order Part Number W10446915

+ 36 hidden pages