Ikea ICI500XB00, ICI500XB01 Installation Guide

30" (76.2 CM) ELECTRICINDUCTION COOKTOP

INSTALLATIONINSTRUCTIONS

INSTRUCTIONSD'INST._.LLATIONDE.

LATABLEDE CUISSON ELECTRIQUEA

INDUCTION DE 30" (76,2 CM)

TableofContents/Table desmati@res

COOKTOP SAFETY ........................................................................... 1

INSTALLATION REQUIREMENTS ................................................... 2

Tools and Parts ............................................................................... 2

Location Requirements ................................................................... 2

Electrical Requirements .................................................................. 3

INSTALLATION INSTRUCTIONS ..................................................... 4

Prepare Location ............................................................................. 4

Install Brackets ................................................................................ 4

Install Cooktop ................................................................................ 5

Make Electrical Connection ............................................................ 5

Complete Installation ....................................................................... 6

SI_CURITI_ DE LA TABLE DE CUlSSON ................................... 7

EXIGENCES D'INSTALLATION .................................................. 7

Outillage et pieces ..................................................................... 7

Exigences d'emplacement ........................................................ 7

Specifications electriques ......................................................... 9

INSTRUCTIONS D'INSTALLATION ........................................... 9

Preparation de I'emplacement .................................................. 9

Installation des supports ........................................................... 9

Installation de la table de cuisson ........................................... 10

Raccordement electrique ........................................................ 11

Achever I'installation ............................................................... 12

COOKTOP SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT:

Save for local electrical inspector's use.

iMPORTANT :

A conserver pour consultation par I'inspecteur local des installations 61ectriques.

501910200567G

INSTALLATIONREQUIREMENTS

/sc nd

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed

• Tape measure • Marker or pencil

• Flat-blade screwdriver • Pliers

• Phillips head screwdriver • 1¼.drill bit

• Hand or electric drill • Jigsaw

• Level

Parts supplied

• Brackets (2)

• 21/2'' (6.4 cm) clamping screws (4)

• #8 x 3/8"(9.5 mm) sheet metal screws (4) Parts needed

• A UL listed or CSA approved strain relief

• UL listed wire connectors Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

30" (76.2 cm) cooktop model/serial rating plate location (models GCI3061, ICI500, KICU500)

......_S_'_'

A. Model/serial rating plate location

• Check the cooktop base for an approved installation label. Verify approved oven model number. If you don't find this label, your cooktop should not be used over a built-in oven. Contact your dealer to confirm that your cooktop is approved.

• Use the countertop opening dimensions that are given with these Installation Instructions. Given dimensions are

minimum clearances and provide 0" (0 cm) clearance.

• Grounded electrical supply is required. See "Electrical Requirements" section.

Product Dimensions

Make sure you have everything needed for correct installation. It is the responsibility of the installer to comply with the installation clearances specified in these instructions.

IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use minimum dimensions given.

• To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

• It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The

model/serial rating plate is located on the underside of the cooktop burner box.

Models G013061 Model I01500 Models KICU500

A. 21%_"(54.1 cm) A. 20_"(51.0cm) A. 21%_"(54.1 cm) B. 30_" (77.0 cm) B. 30_" (77.0 cm) B. 30_" (78.2 cm) C. 2_" (6.0 cm) C. 2_" (6.0 cm) C. 2_" (6.0 cm)

Cabinet Dimensions

IMPORTANT: If installing a range hood or microwave hood

combination above the range, follow the range hood or microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

A. 29_/2" (75.0 cm) on 30" (76.2 cm) models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet (24" [61 cm] minimum clearance if bottom of wood or metal cabinet is covered

by not less than ¼" [0.6 cm] flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)

D. 13" (33.0 cm) recommended upper cabinet depth

E.2"(5.1 cm) F. 19_" (49.0 cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of

cou ntertop

I.Junction box or outiet; 10" (25.4 cm) from right-hand side of

cabinet

J. 29_/2'' (75.0 cm) on 30" (76.2 cm) models

K. 1" (2.5 cm) minimum distance to nearest/eft and right side

combustible surface above cooktop

L. 1" (2.5 cm) minimum clearance between back wall and countertop

NOTES: After you make the countertop cutout, some installations may require notching down the base cabinet side

walls to clear the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.

If cabinet has a drawer, a 5W' (13 cm) depth clearance from the countertop to the top of the drawer (or other obstruction) in base cabinet is required.

Electrical Shock Hazard

Disconnect power before servicing. Use 8 gauge copper wire.

Electrically ground cooktop. Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local

codes. Check with a qualified electrical installer if you are not sure the

cooktop is properly grounded. It is not recommended to have a fuse in the neutral or ground

circuit. Make sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94,

Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association 1 Batterymarch Park

Quincy, MA 02169-7471 CSA International

8501 East Pleasant Valley Road Cleveland, OH 44131-5575

Before You Make the Electrical Connection: To properly install your cooktop, you must determine the type of

electrical connection you will be using and follow the instructions provided for it here.

• A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only electrical supply is required on a separate, 50-amp circuit (36" [91.4 cm] models) or 40-amp circuit (30" [76.2 cm] models), fused on both sides of the line.

• The cooktop should be connected directly to the junction box through flexible, armored or nonmetallic sheathed, copper cable. The flexible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the junction box.

• Locate the junction box to allow as much slack as possible between the junction box and the cooktop so that the cooktop can be moved if servicing becomes necessary in the

future. Do not cut the conduit. The length of conduit provided is for

serviceability of the cooktop. A UL listed or CSA approved conduit connector must be

provided at each end of the power supply cable (at the cooktop and at the junction box). A listed conduit connector is already provided at the cooktop.

Ifthehousehasaluminumwiring,followtheprocedure below:

1. Connectasectionofsolidcopperwiretothepigtail leads.

INSTALLATIONINSTRUCTIONS

1. Decide on the final location for the cooktop. NOTE: Countertop must be 13/16'' (3.0 cm) to 2" (5.1 cm) thick.

2. If necessary, make cutout in countertop before installing cooktop. See "Location Requirements" section for more

information.

3. Clean cutout of any remaining dust and debris.

_ _ J_ ,,_

NOTE: Kit Part Number W10310006 is required for installing the cooktop into a solid surface or marble countertop. See the

"Assistance or Service" section of the Use and Care Guide for information on ordering.

To Install Brackets into Marble Countertop:

1. Clean the brackets and cooktop cutout of any dust and debris.

2. Connectthealuminumwiringtotheaddedsectionof copperwireusingspecialconnectorsand/ortools designedandULlistedforjoiningcoppertoaluminum.

Followtheelectricalconnectormanufacturer'srecommended procedure.Aluminum/copperconnectionmustconformwith

localcodesandindustryacceptedwiringpractices.

4. Position brackets in the center of the vertical centerline and align the upper edge of the brackets so that they are flush

with the countertop.

Push the brackets firmly onto each side of the cooktop cutout and wait 1 hour for adhesive to dry.

Measure the center line of the vertical sides of the cooktop cutout.

Center line

Apply the adhesive provided in the kit to the back side of the brackets.

To Install Brackets into Wood Countertop:

1. Measure the center line of the vertical sides of the cooktop cutout.

Center line

2. Position brackets in the center of the vertical centerline and align the upper edge of the brackets so that they are flush

with the countertop.

3. Attach the brackets in the cutout with the screws provided.

A. Bracket B. Screw

+ 8 hidden pages