Ikea IBS124PSS1, IBS224PSM1, IBS324PSW00, IBS324PSW1 Installation Guide

INSTALLATIONINSTRUCTIONS

24" (61 CM) ELECTRICBUILT-INOVEN

INSTRUCTIONSD'INSTALLATION

FOURELECTRIQUEENCASTREDE24" (61 CM)

Table of Contents / Table des mati_res

BUILT-IN OVEN SAFETY ................................. 1

INSTALLATION REQUIREMENTS .................. 2

Tools and Parts ............................................. 2

Location Requirements ................................. 2

Electrical Requirements ................................ 3

INSTALLATION INSTRUCTIONS .................... 4

Prepare Built-In Oven .................................... 4

Remove Oven Door ....................................... 4

Make Electrical Connection .......................... 4

Install Oven .................................................... 5

Complete Installation .................................... 6

SI_CURITI_ DU FOUR ENCASTRI_ .................. 7

EXIGENCES D'INSTALLATION ....................... 7

Outillage et pieces ......................................... 7

Exigences d'emplacement ............................ 7

Specifications electriques .............................. 8

INSTRUCTIONS D'INSTALLATION ................. 9

Preparation du four encastre ......................... 9

D_pose de la porte du four ............................ 9

Raccordement electriq ue ............................ 10

Installation du four ....................................... 11

Achever I'installation .................................... 12

BUILT-INOVEN SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT: Save for local electrical inspector's use.

iMPORTANT : A conserver pour consultation par I'inspecteur local des installations 61ectriques.

501910200218

INSTALLATIONREQUIREMENTS

s c nd Js(xds

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed

• Phillips screwdriver

• Measuring tape

• Level

• Hand or electric drill (for wall cabinet installations)

• 1" (25 ram) drill bit (for wall cabinet installations) Parts needed

• UL listed or CSA approved conduit connector

• UL listed wire connectors

Undercounter Installation (with cooktop installed above):

Ovens approved for this type of installation have an approval label located on the top of the oven. Refer to undercounter installation

instructions for cutout dimensions and approved oven cooktop combinations (separate sheet).

Product Dimensions

Parts supplied

• Four # 8-14 x 1" screws

• Four 4 x 13 mm screws

• 2 mounting rails

• 2 continuous-clean panels and rack guides

• Broil pan and grid Check local codes. Check existing electrical supply. See

"Electrical Requirements." It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

Make sure you have everything needed for correct installation. It is the responsibility of the installer to comply with the installation

clearances specified in these instructions. IMPORTANT: Observe all governing codes and ordinances.

• Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with oven.

• Recessed installation area must provide complete enclosure around the recessed portion of the oven.

• Grounded electrical supply is required. See "Electrical Requirements" section.

Electrical supply junction box should be located 3" (7.6 cm) maximum below the support surface when the oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should be located in the right rear or left rear corner of the

support surface to pass the appliance cable through to the junction box.

NOTE: For undercounter installation, it is recommended that the junction box be located in the adjacent right or left

cabinet. If you are installing the junction box on rear wall behind oven, the junction box must be recessed and located in the upper or lower right or left corner of the cabinet; otherwise, the oven will not fit into the cabinet opening.

Oven support surface must be solid, level and flush with bottom of cabinet cutout. Floor must be able to support a single oven weight of 140 Ibs (63.5 kg) or a double oven weight of 245 Ibs (111.1 kg).

A. 21_%4 '' (54.5 cm) max. recessed width B. 2217/32" (5 7.2 cm) recessed height C. 2327/64'' (59.5 cm) max. overall height D. 213/16 '' (53.8 cm) max. recessed depth

E. 2327/64'' (59.5 cm) overall width

Cabinet Dimensions

Oven Undercounter (without cooktopinstalledabove)

A. 24" (61.0 cm) min. cabinet width

B. 11/_'' (3.8 cm) min. top of cutout to

underside of countertop

C. 51/4'' (13.3 cm) bottom of cutout to floor

D. 221/=''(57.2 cm) cutout width

E. 231/3_"(58.5 cm) min. cutout height

Oven Installed in Cabinet

A. 24" (61.0 cm) min. cabinet width B. 1" (2.5 cm) top of cutout to bottom of upper

cabinet door

C. 32" (81.3 cm) bottom of cutout to floor D. 221/2'' (57.2 cm) cutout width

E. 11/2'' (3.8 cm) min. bottom of cutout to top of

cabinet door

F. 23½2" (58.5 cm) min. cutout height

Cabinet Side View

It is not recommended to have a fuse in the neutral or ground circuit.

This oven must be connected to a grounded metal, permanent wiring system.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. O-M91-1atest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

• Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located at the bottom of the right-hand mounting rail. See the following

illustration.

A. 231/4'' (59.1 cm) min. cutout depth B. 23" (58.4 cm) recessed oven depth

C. Oven front D. Recessed oven

E. Cabinet

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local codes.

It is not recommended to ground to a gas pipe. Check with a qualified electrical installer if you are not sure the

oven is properly grounded.

Single Oven

A. Model/serial number pla te

Models rated at 7.2 kW and below at 240 volts (5.4 kW and below at 208 volts) require a separate 30-amp circuit.

A time-delay fuse or circuit breaker is recommended. Connect directly to the fused disconnect (or circuit breaker

box) through flexible, armored or nonmetallic sheathed, copper cable (with grounding wire). See "Make Electrical

Connection" section. Flexible cable from oven should be connected directly to the

junction box. Fuse both sides of the line.

Do not cut the conduit. The length of conduit provided is for serviceability of the oven.

A UL listed or CSA approved conduit connector must be provided.

If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

INSTALLATIONINSTRUCTIONS

_,,_F,,_ _ _ ',%: __,_ .......

NOTE: The IKEA®Column Cabinet is available for installation but not required. The oven may also be installed into custom cabinets.

1. Decide on the final location for the oven.

Excessive Weight Hazard

Use two or more people to move and install oven. Failure to do so can result in back or other injury.

2. To avoid floor damage, set the oven onto cardboard prior to installation. Do not use oven door handle or any portion of the front frame or trim for lifting.

3. Remove the shipping materials and tape from the oven.

4. Remove the hardware package from inside the bag containing literature.

5. Remove and set aside racks and other parts from inside the oven.

6. Move oven and cardboard close to the oven's final location.

em eOve s©

IMPORTANT: Use both hands to remove oven doors.

1. Open oven door all the way.

2. Flip up the hinge latch on each side.

Meek®E®c c<s Co s sect

Electrical Shock Hazard

Disconnect power before servicing. Use 12 gauge copper wire.

Electrically ground oven. Failure to follow these instructions can result in death,

fire, or electrical shock.

This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together.

1. Disconnect power.

2. Feed the flexible cable conduit from the oven through the opening in the cabinet.

3. Remove junction box cover if it is present.

4. Install a UL listed or CSA approved conduit connector to the junction box.

3. Close the oven door as far as it will shut.

4. Lift the oven door while holding both sides. Continue to push the oven door closed and pull it away from

the oven door frame.

A....................

A. UL listed or CSAapproved conduit connector

5. Route the flexible cable conduit from the oven to the junction box through a UL listed or CSA approved conduit connector.

6. Tighten screws on conduit connector.

7. See "Electrical Connection Options Chart" to complete installation for your type of electrical connection.

Electrical Connection Options Chart

If your home has: Go to section:

4-wire 4-wire Cable from Home

Power Supply

1/2"

(1.3 cm)

3-wire 3-wire Cable from Home

k__ Power Supply

+ 8 hidden pages