iHome IP16 User Manual

Model iP16

Portable Alarm Clock Speaker

System for your iPhone / iPod

Table of Contents

Quick Start Controls and Indicators

iP16 Display Install Clock Backup Battery Using iP16 Charging your iPhone / iPod Listening to your iPhone / iPod Setting the Time Alarm Operation Sleep Operation Snooze/Dimmer Operation A Consumer Guide to Product Safety Trouble Shooting Solución De Problemas Warranty Information

1 2 3 3 4 4 4 5 6 7 7 8

9 10 11

Maintenance

• Place the unit on a level surface away from sources of direct sunlight or excessive heat.

• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material

should be placed between it and the furniture.

• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine,

thinner or similar materials can damage the surface of the unit.

NOTE: Be careful not to touch the surface of the speakers at either end of the unit

Getting Started

Thank you for purchasing the iHome iP16 Audio Speaker System for your iPhone/iPod. Designed specifically to work with your iPhone/iPod, this system provides high quality audio performance that brings out the best in your music. Please read this instruction book carefully before operating the iP16 and keep it for future reference.

Questions? Visit www.ihomeaudio.com

Check for iPhone/iPod compatibility

iP16 is an advanced system and supports most updated iPod features. To make sure your iPhone/iPod works properly with iP16, please update your iPhone/iPod firmware with the latest version via iTunes.

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Battery Warning

For models that use Lithium batteries

• Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high

temperatures & not handled appropriately

• Do not place loose batteries in a pocket, purse, or other container containing metal objects, do not mix with used or other

battery types, or store with hazardous or combustible materials.

• Store in cool, dry, ventilated area.

• Follow applicable laws and regulations for transport and disposal.

For models that require more than one battery

• Do not mix with used or other battery types/brands

• Replace all batteries at the same time

• Do not open batteries

• Do not dispose of in fire

• Do not heat above 75ºC (167ºF)

• Do not expose contents to water

• Do not charge or recharge

• Do not install backwards

Quick Start

RESET

TEST

Attach the AC adaptor cable to the DC jack on the back of the iP16 and plug the other end into a working wall socket. For portable operation, remove battery compartment door on the bottom of the unit and insert 4 AA batteries (see diagram on page 4).

Use this insert

no insert needed for

iPod Classic 160 GB

iPhone 3G/3GS

iPod nano 6G

4:time

For this

iPhone/iPod

2:inserts

3:iPhone/iPod1:power

See the table below to find which side of the dock insert matches your iPhone/iPod model and place insert in dock. NOTE: iPhone 3G, iPhone 3GS, iPod Classic 160 GB and nano 6G do not require the insert.

1) Turn insert so correct side of the insert for your iPhone/iPod is facing the display.

2) Slide insert downwards until it snaps into place

Classic/Touch side Nano side

iPod classic (80, 120 GB)

iPhone 4, iPod touch

Gently dock iPhone/iPod into dock (iPhone/iPod must not be in a skin or case). iPhone/iPod will charge while docked. Press the Power Button on the iP16 to play the iPhone/iPod.

all iPod nano models

up to nano 5G

To use Time Sync, dock your iPhone or iPod touch and press the Clock Adj. Button. SYN will appear on the display and the unit will sync to the

time on your iPhone or iPod. To set time manually,

• Press the DST On/Off Button on the back of the unit as needed to add or subtract an hour for daylight saving time or standard time.

• Press & Hold the Clock Adj. button on the back of the unit until the hour display flashes.

• Press the + or - buttons to set the hour, then press the Clock Adj. button

• Press the + or - buttons to set the minutes then press the Clock Adj.

button again to confirm time setting.

Controls and Indicators

iP16 Display

Up/Plus Button

Increase volume, time setting

Down/Minus Button

Decrease volume, time setting

DST On/Off button

Press to add or subtract 1 hour for daylight saving time

Front Panel

Press for Sleep mode

Snooze/Dimmer Button

Silence alarm temporarily or adjust display brightness

Back Panel

Clock Adj. ButtonSleep Button

Press and hold for Clock Adjust mode

Power Button

Press to power unit ON or OFF

Alarm Button

Press and hold for Alarm Setting mode

DC Jack

Connect AC adapter

PM Indicator

Time Display

Daylight Saving Time

Indicator

Install Clock Backup Battery

The iP16 uses a CR2032 button cell battery (included with instructions) to keep alarm and clock settings in the event of a power failure and 4 “AA” batteries to maintain alarm operation. If the Backup Battery has been installed and a power failure occurs or the AC adaptor is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. If 4 “AA” batteries are installed, alarm will operate when unit is not connected to AC adaptor.

1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement.

2. Open and remove the battery compartment door located on the bottom of the unit.

3. Pinch the backup battery release tab and pull the backup battery holder free.

4. Insert one CR2032 button cell battery with the + side facing upwards.

5. Replace the backup battery holder into the unit, then replace the battery compartment door.

Note: Make sure you dispose of batteries properly (see your local regulations). Note: Buttons will not function if only back up battery installed.

Alarm Indicator

iPhone/iPod Indicator

Sleep Indicator

Battery Low Indicator



Pinch to release

Installing Backup Battery

+ 5 hidden pages