iHome iCVBT4 User Manual
iHome Beauty
iCVBT4 - QSG (English)
Instruction manual - US English
size: 510mm(W) x 150mm(H)
Folded Size: 102 x 150 mm
material: 154gsm, art card, 1C + 1C, 直角
May 25, 2020
Front Cover
REFLECT TRIFOLD
Model: iCVBT4
Vanity Speaker
Quick Start Guide
QUESTIONS? visit www.ihome.com
WHAT’S INCLUDED:
iCVBT4 Vanity Speaker
Removable Detail Mirror
The back of the 10x magnifying
detail mirror has SimpleStick™ micro
suction material for easily attaching
and detaching almost anywhere.
AC Adapter
Cleaning Cloth
Use to keep the large surface and
detail mirror smudge-free.
SETUP OVERVIEW
Open the left and right side
panels of the REFLECT TRIFOLD
and adjust the angles as needed.
CONNECTING MIRROR TO POWER
Connect included AC adapter to DC jack on back of mirror
and the other end to a working wall outlet.
Bluetooth
Pairing
Button
DC Jack
9V/2A
outlet
CONNECTING TO BLUETOOTH
• Press the Power Button to turn the unit ON.
• Press and hold the Bluetooth Pairing Button (on the back of
the unit) for 3 seconds. The blinking icon on the front panel
will indicate the unit is in pairing mode.
• Select ‘iHome Reflect TRIFOLD’ on your device’s Bluetooth
menu to connect. The icon will glow solid to confirm your
device is connected.
1
USB Charging
Port (1A)
USB
FRONT PANEL
BACK PANEL
Power Button
Press to turn mirror ON or OFF
Minus/Plus Volume Buttons
Press to lower or raise volume
Multi-Function Button
Press to play/pause audio
Press to Answer/End calls
Press and hold to decline calls
Press and hold to access Siri
or Google Assistant
Light Button
Press to adjust brightness of mirror light
Press and hold to change light mode
Note: Power and Light features operate separately:
USB
DC Jack
Use included adapter to connect
to AC power
Bluetooth Button
- Press and hold for 3 seconds
to enter pairing mode
- Press and hold for 10 seconds to reset
Bluetooth if necessary
USB 1A Charging Port
When the mirror is connected to
AC power, use the USB port to
charge devices
• Press the Power Button to access audio features including
Bluetooth.
• Press the Light Button to access light modes and brightness
levels.
2
3
4
LIGHT FUNCTION
• Press the Light Button to turn the mirror light ON.
• Press the Light Button repeatedly to cycle through brightness
levels:
High, Mid, Low, and OFF.
• Press and hold the Light Button to cycle through light modes:
Warm, Bright, and Cool.
Three Color Light Modes:
• Warm
Simulates low light environments for a night out
• Bright
Emulates outdoor/sunlight for closer detail
• Cool
Matches standard indoor/oce settings
Note: After 60 minutes of inactivity, the light will automatically shut
o. Press the Light Button again to resume the previous light mode
settings. (This will not aect Bluetooth audio.)
USING BLUETOOTH AUDIO
Use the Multi-Function Button to:
• Play /pause Bluetooth audio
• Answer/end Bluetooth calls
• Press and hold for 3 seconds to decline incoming Bluetooth calls
• Quick double press for next track
• Quick triple tap for previous track or to restart current track
Use the + and - Buttons to adjust volume
5
CHARGING DEVICES
Unit MUST be connected to AC power to charge devices via USB.
• Connect USB charging cable (not included) to USB port and the
other end to your device to charge.
outlet
USB
DETAIL MIRROR
• Remove the protective tape from the back of the included 10x
magnifying detail mirror and attach wherever you like on the
mirror face (or anywhere!)
• The back of the detail mirror has SimpleStick™ micro suction
material. If necessary, clean SimpleStick material with oce tape.
MAINTENANCE
• Place the unit on a level surface away from sources of direct sunlight
or excessive heat.
• Protect your furniture when placing your unit on a natural wood
and lacquered finish. A cloth or other protective material should
be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap
and water. Stronger cleaning agents such as thinner or similar
materials can damage the surface of the unit.
• This mirror comes with a cleaning cloth to keep the large surface
and detail mirror smudge-free.
• Wash the mirrors with mild soap and water as needed.
• Close the side mirror panels during shipping, storage, or periods
of non-use.
6
IMPORTANT SAFETY INSTRUCTIONS
Please heed all warnings, read and follow all instructions and keep
these instructions handy for future reference.
1. Do not use this product near water, and clean only with dry cloth.
2. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
3. Heat – This product should be situated away from heat sources
such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Only use attachments/accessories specified by the manufacturer.
5. Unplug this product during lightning storms or when unused for
long periods of time.
6. Damage Requiring Service – This product should be serviced by
qualified service personnel when:
- Plug has been damaged.
- Objects have fallen into or liquid has been spilled into the
enclosure.
- The unit has been exposed to rain. The unit has been dropped
or the enclosure damaged.
- The unit exhibits a marked change in performance or does not
operate normally.
7. No naked flame sources, such as lighted candles, should be
placed on this product.
8. Attention should be drawn to the environmental aspects of
battery disposal.
9. This product is suitable for use in tropical and/or moderate
climates.
10. WARNING: To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
11. The mains plug of power adaptor is used as the disconnect
device, it shall remain readily operable.
12. Never place the mirror in or expose the mirror to direct sunlight.
The sun’s rays can reflect to become focused and cause
excessive heat and/or fire. Do not use mirror in direct sunlight as
reflected sunlight could injure eyes.
7
FCC INFORMATION
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
IC Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
The device comply with ISEDC RF exposure requirement, users can obtain Canadian information on RF
exposure and compliance.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator
and your body.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un
environnement non contrôlé.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
L'appareil est conforme aux exigences d'exposition RF ISEDC, les utilisateurs peuvent obtenir des
informations canadiennes sur l'exposition aux RF et la conformité.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre
corps.
Tout changement ou modification non expressément approuvé par la partie responsable de la conformité
peut annuler l'autorité de l'utilisateur à utiliser l'équipement.
CAN ICES 3(B) / NMB-3(B)
8
ONE YEAR LIMITED WARRANTY
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI),
warrants this product to be free from defects in workmanship and materials,
under normal use and conditions, for a period of one (1) year from the date of
original purchase. Should this product fail to function in a satisfactory manner, it
is best to first return it to the store where it was originally purchased. Should this
fail to resolve the matter and service still be required by reason of any defect or
malfunction during the warranty period, SDI will repair or, at its discretion,
replace this product without charge. This decision is subject to verification of the
defect or malfunction upon delivery of this product to the Factory Service
Center authorized by Customer Service.
If service is required, please contact Customer Service at
ihomeaudio.com/support/contact to obtain a Return Authorization Number and
shipping instructions. A copy of the sales receipt is required to validate
in-warranty coverage. If proof of purchase cannot be produced, the product will
be deemed out-of-warranty. The date of purchase, vendor, product model
number, and purchase price must be legible and verifiable.
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which
it was designed. It does not cover (i) products which have been damaged by
negligence or willful actions, misuse or accident, or which have been modified or
repaired by unauthorized persons; (ii) cracked or broken cabinets, or units
damaged by excessive heat; (iii) damage to digital media players, CD’s or tape
cassettes (if applicable); (iv) the cost of shipping this product to the Factory
Service Center and its return to the owner. This warranty is valid only in the
United States of America and does not extend to owners of the product other
than to the original purchaser. In no event will SDI or any of its aliates,
contractors, resellers, their ocers, directors, shareholders, members or agents
be liable to you or any third party for any consequential or incidental damages,
any lost profits, actual, exemplary or punitive damages.
(Some states do not allow limitations on implied warranties or exclusion of
consequential damages, so these restrictions may not apply to you.) This
warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. Your acknowledgment and agreement to fully
and completely abide by the above mentioned disclaimer of warranty is
contractually binding to you upon your transfer of currency (money order,
cashier's check, or credit card) for purchase of your SDI product.
© 2020 SDI Technologies, Inc. All rights reserved
Questions? Visit www.ihome.com
iCVBT4QSG-052520-A Printed in China
Tim: 5/25/20
Loading...