Page 1
Date
SKU
igo
Drafting Chair/Bar Stool
igoseating
Supports
up to 250 lbs
////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Assembly Instruction
Congratulation on your buying of this premium drafting chair/Bar stool, which reflects the
SeatHealth Engineering technique our R&D team had worked for years, to protect your spine &
buttocks, and specially your seating health as a whole. Enjoy & Thank You!
Manufactured : June, 2022
# : F026A01EM1-WF1(Blue), F026A01EM2-WF1(Purple), F026A01EM3-WF1(Grey)
F026A01EM4-WF1(Orange), F026A01EM5-WF1(Green)
Page 1
Page 2
PARTS LIST
Name Part Qty.
A Fixed Leg/Caster 2x5PCS
B Star Base x1PC
C Gas Lift x1PC
D Connecting Cover x1PC
E Seat Cushion x1PC
F
G Seat Plate x1PC
J Bar (L+R)
x1PAIR
H
Back with Lumbar
x1PC
Cushion
Page 2
Page 3
J Star Base Cover x1PC
K
M6x18mm
x4PCS
Bolts
Bolts
L
M6x32mm
x8PCS
Washer
M
Φ18*Φ6mm
x8PCS
N Allen Wrench x1PC
P Plastic Cover x4PCS
Page 3
Page 4
Please follow the following procedures step by step in building your
Drafting Chair/Bar Stool, take special note to the sequence of steps:
With the igo Drafting Chair/Bar Stool purchased, both Fixed Legs and Casters are provided for
your choice of mobility of the chair, and they are interchangable anytime you may require.
Step 1: Place the Star Base (Part B) upside down and insert the 5 Fixed Legs or Casters (Part A)
into the holes at the end of each leg of the Star Base (Part B).
Step 2: Turn the Star Base (Part B) over and insert Gas Lift (Part C) with Star Base Cover (Part J)
through the center hole on top of Star Base (Part B).
Step 3: Attach connecting cover(Part D) to Left and Right J-Bar (Part F), and attach Left and Right
J -Bar (Part F) to the Back (Part H) by using bolts (Part Lx4pcs). Tighten the bolts then cover the
holes with the plastic cover (Part P x4pcs).
Page 4
Page 5
Step 4: Attach the Seat Plate (Part G) to Seat Cushion (Part E) by using 4 Bolts (Part K) and
washers (Part M x4pcs) in the front holes & back holes. Tighten by Allen Wrench (Part N). Take
special note to the sticker which should point to the seat front.
Step 5: Attach the Back (Part H) to the Seat Cushion(Part E) by using bolts (Part L x4pcs) and
washers (Part M x4pcs).
Step 6: Position the assembled chair upright with the seat plate facing down. Insert the Gas
Lift (Part C) into the center hole of the Seat Plate (Part G) and press down until fully engaged.
4
ATTENTION：Make sure all bolts and screws are fully tightened before using chair.
* This Chair is for sitting only. Do not stand on this chair. Do not use this chair as a step ladder.
* Use this chair only for seating one person at a time.
* Do not use this chair unless all bolts, screws and other parts are firmly tightened.
* Every month, check all bolts, screws and other parts and tighten any that may have loosened.
* If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made,
using factory supplied parts.
Page 5
Page 6
SEAT HEIGHT ADJUSTMENT
FUNCTION
INSTRUCTION
While seated, reach to the right side of the chair to find the handle, and turn handle
to raise and lower seat height to adapt to your different body heights.
LUMBAR PILLOW ADJUSTMENT
Lumbar pillow can be attached to the desired position of your body.
Page 6
Loading...