IGNIS AKS 339/IX User Manual
EN
BUILT-IN GAS HOB INSTRUCTIONS
NL
IMPORTANT SAFETY INSTRUCTIONS
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to be read and observed at all times.
This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.
All safety messages will follow the safety alert symbol and either the terms:
DANGER
WARNING
All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what
can happen if the instructions are not followed.
- The appliance must be disconnected from the power supply before carrying out any installation work.
- Installation and maintenance must be carried out by a qualied technician, in compliance with the manufacturer’s instructions and local safety regulations. Do not repair or replace any part of the appliance unless specically stated in the
user manual.
WARNING
- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this appliance.
What to do if you smell gas:
- Do not try to light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the gas supplier.
- Use appliance in well ventilated rooms only.
Indicates a hazardous situation which, if not avoided, will cause serious injury.
Indicates a hazardous situation which, if not avoided, could cause serious injury.
If the information in this manual is not followed exactly, a re or explosion may result
causing property damage or injury.
The electrical and gas connections must comply with local regulations.
The electrical and gas connections must comply with local regulations.
- When the hob is installed, provide a multi-pole circuit breaker with a contact separa-
tion of at least 3 mm, that provides full disconnection.
- Regulations require that the appliance is grounded.
- The power cable must be long enough for connecting the appliance, once tted in
its housing, to the power supply
- Use only exible or rigid metal hose for gas connection.
- If necessary, the electrical power cable must be replaced exclusively with a power
cable having identical characteristics to the original supplied by manufacturer. This
operation must be performed by a qualied electrician.
- The manufacturer cannot be held responsible for any injury to persons or animals or
damage to property arising from failure to comply with these requirements.
- Do not use multiple plug adapters or extension cords.
- Do not pull the power cable to disconnect it from the electrical supply.
- The electrical components must not be accessible to the user after installation.
- Do not touch the appliance with any wet part of the body and do not operate it
when barefoot.
- This hob (class 3) is designed solely for private household use for cooking food. Do
not use this appliance as a space heater to heat or warm the room. Doing so may re-
sult in carbon monoxide poisoning and overheating of the hob. The Manufacturer
declines all responsibility for inappropriate use or incorrect setting of the controls.
- The appliance and its accessible parts become hot during use. Care should be taken
to avoid touching heating elements. Children less than 8 years of age shall be kept
away unless continuously supervised. This appliance can be used by children aged
from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the
hazards involved. They shall not play with the appliance. Cleaning and user maintenance shall not be made by children supervision.
- The use of a gas appliance produces heat and humidity in the room. Make sure the
room is well-ventilated, or install an extractor hood with exhaust duct.
- Domestic animals should be kept away from the appliance.
- In case of prolonged use, additional ventilation may be necessary (by opening a window
or increasing the hood extraction speed).
- After use, make sure the knobs are in o position and close the main gas supply
cock or the gas cylinder valve.
- Overheated oils and fats catch re easily. Always remain vigilant when cooking
foods rich in fat, oil or alcohol (e.g. rum, cognac, wine).
- Keep the packaging materials out of the reach of children.
- Before cleaning or maintenance wait for hob to cool down.
- Unattended cooking on a hob with fat or oil can be dangerous and may result in
re. NEVER try to extinguish a re with water, but switch o the appliance and then
cover ame e.g. with a lid or a re blanket.
- Danger of re: do not store items on the cooking surfaces.
SAVE THESE INSTRUCTIONS
INSTALLATION
After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the
dealer or your nearest After-sales Service.
These instructions are only valid for the countries whose symbols is given on the data plate (under the hob).
TECHNICAL INFORMATION FOR THE INSTALLER
• This product can be embedded in a worktop 20 to 50 mm thick.
• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening
in the work surface. This panel, that has to close completely the cutout in order to avoid any contact with the
bottom part of the hob, must be positioned at a maximum distance of 150 mm below the upper surface of the
work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an
oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The
manufacturer declines all liability if another brand oven is installed beneath the hob.
• Before installation, make sure that:
- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the
rating plate and injector table);
- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
- this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation
regulations. Particular attention shall be given to the relevant requirements regarding ventilation; - combustion products are discharged outdoors through specic hoods or wall and/or window mounted electrical fans.
400010772431 Manufacturer: Whirlpool Europe S.r.l. Viale G. Borghi, 27 21025 Comerio (VA) ITALY
GAS CONNECTION
WARNING
This operation must be performed by a qualied technician.
sions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and
fasten them by means of their screws in accordance with the thickness of the worktop (see the following gures).
• The gas supply system must comply with local regulations.
• You can nd specic local regulations for some countries in the paragraph
“Reference to Local Regulations”. If no information concerning your Country
is given, please ask details to your Installer.
• The connection of the hob to the gas pipe network or gas cylinder must
be made by means of a rigid copper or steel pipe with ttings complying
with local regulations, or by means of a continuous-surface stainless steel
hose complying with local regulations. Interpose gasket (B) in the elbow
connection.The maximum length of the hose is 2 m.
• FOR BELGIUM ONLY: It is necessary to replace the elbow connection (A) on
the appliance, with the one supplied (if present).
IMPORTANT: if a stainless steel hose is used, it must be installed so as not
to touch any mobile part of the furniture. It must pass through an area
where there are no obstructions and where it is possible to inspect it on
all its length.
• After connection to the gas supply, check for leaks with soapy water. Light
up the burners and turn the knobs from max position to minimum posi-
tion to check ame stability.
(Apply the label from warranty here)
Top 30-50 mm
Top 20 mm
ADJUSTMENT TO DIFFERENT TYPES OF GAS
WARNING
If the appliance is intended to operate with a dierent gas from the gas type stated on the rating plate and information label
on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
• The gas nozzles must be changed by After Sales Service or a qualied technician.
• Nozzles not supplied with the appliance must be ordered from After Sales Service.
• Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will
go.
IMPORTANT: should you experience diculty in turning the burners knobs, please contact the After Sales Service for
the replacement of the burner tap if found to be faulty.
This operation must be performed by a qualied technician.
ELECTRICAL CONNECTION
WARNING
WARNING
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
This operation must be performed by a qualied technician.
• The electrical connections must comply
with local regulations.
• The earthing of this appliance is
compulsory by law.
• Do not use an extension cord.
ASSEMBLY
After having cleaned the perimeter surface,
apply the supplied gasket to the hob as shown in the gure.
Position the hob in the worktop opening made re- specting the dimen-
L Earth
(yellow/green)
N
REPLACING THE INJECTORS (see the injector table in the Instruction)
• Remove grids (A).
• Extract burners (B).
• Using a socket spanner of the appropriate size unscrew the
injector (C), unscrew the injector to be replaced.
• Replace it with the injector suitable for the new type of
gas.
• Re-assemble the injector in (D).
• If you have a multiple crown burner use side spanner to
replace the injector (E).
Before installing the hob, remember to ax the gas calibration
plate supplied with the injectors in such a way that it covers
the existing information relating to gas calibration.
Loading...