IEI Integration AFL2-15A-H61 User Manual

User Manual
AFL2-15A-H61
MODEL:
AFL2-15A-H61 Series
Flat Bezel Panel PC with 2nd Generation Intel® Core™ i7/ i5/ i3,
Pentium® and Celeron® Processor, Touch Screen, Wi-Fi, USB,
HD Audio and RoHS
User Manual
Rev. 1.01 - 25 July, 2013
Page I
Date Version Changes
AFL2-15A-H61
Revision
25 July, 2013 1.01
11 October, 2012 1.00
Added information of the CPU temperature alert LED in Section Updated Section Initial release
8.3.7: RS-422/485 RJ-45 Serial Port (COM3)
1.2.1.1.
Page II
AFL2-15A-H61
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
Copyright
reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.
Page III
AFL2-15A-H61
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.1.1 Model Variations................................................................................................ 3
1.1.2 Features ............................................................................................................. 3
1.1.3 Light Fanless Technology Design...................................................................... 4
1.2 EXTERNAL OVERVIEW................................................................................................ 4
1.2.1 Front Panel........................................................................................................ 4
1.2.1.1 LED Indicators............................................................................................ 5
1.2.1.2 Function Keys............................................................................................. 7
1.2.2 Rear Panel ......................................................................................................... 8
1.2.3 Bottom Panel...................................................................................................... 9
1.2.4 Side Panels....................................................................................................... 10
1.3 DIMENSIONS............................................................................................................. 10
1.4 INTERNAL OVERVIEW................................................................................................11
1.5 SYSTEM SPECIFICATIONS.......................................................................................... 12
2 UNPACKING............................................................................................................... 14
2.1 UNPACKING.............................................................................................................. 15
2.1.1 Packing List ..................................................................................................... 15
3 INSTALLATION ......................................................................................................... 19
3.1 ANTI-STATIC PRECAUTIONS...................................................................................... 20
3.2 INSTALLATION PRECAUTIONS ................................................................................... 20
3.3 INST ALLATION AND CONFIGURATION STEPS............................................................. 21
3.4 HDD INSTALLATION................................................................................................. 21
3.5 CF CARD INSTALLATION .......................................................................................... 24
3.6 RFID READER INSTALLATION (OPTIONAL) .............................................................. 25
3.7 AT/ATX MODE SELECTION...................................................................................... 27
3.7.1 AT Power Mode................................................................................................ 27
3.7.2 ATX Power Mode............................................................................................. 27
3.8 CLEAR CMOS.......................................................................................................... 28
Page IV
AFL2-15A-H61
3.9 RESET THE SYSTEM.................................................................................................. 28
3.10 POWERING ON THE SYSTEM................................................................................... 29
3.11 POWERING OFF THE SYSTEM.................................................................................. 29
3.12 MOUNTING THE SYSTEM ........................................................................................ 29
3.12.1 Wall Mounting................................................................................................ 30
3.12.2 Arm Mounting ................................................................................................ 33
3.12.3 Stand Mounting.............................................................................................. 34
3.13 EXTERNAL PERIPHERAL DEVICE CONNECTION ...................................................... 35
3.13.1 Audio Connection........................................................................................... 36
3.13.2 HDMI Device Connection.............................................................................. 36
3.13.3 LAN Connection............................................................................................. 37
3.13.4 Serial Device Connection .............................................................................. 38
3.13.4.1 DB-9 Serial Port Connection.................................................................. 38
3.13.4.2 RJ-45 Serial Port Connection.................................................................. 39
3.13.5 Type K T emperatur e Sensor Connection........................................................ 40
3.13.6 USB Device Connection................................................................................. 41
3.13.7 VGA Monitor Connection .............................................................................. 42
4 BIOS SETUP................................................................................................................ 44
4.1 INTRODUCTION......................................................................................................... 45
4.1.1 Starting Setup................................................................................................... 45
4.1.2 Using Setup...................................................................................................... 45
4.1.3 Getting Help..................................................................................................... 46
4.1.4 Unable to Reboot after Configuration Changes.............................................. 46
4.1.5 BIOS Menu Bar................................................................................................ 46
4.2 MAIN........................................................................................................................ 47
4.3 ADVANCED............................................................................................................... 48
4.3.1 ACPI Settings................................................................................................... 49
4.3.2 RTC Wake Settings ........................................................................................... 50
4.3.3 T rusted Computing........................................................................................... 52
4.3.4 CPU Configuration.......................................................................................... 52
4.3.4.1 CPU Information....................................................................................... 53
4.3.5 SATA Configuration ......................................................................................... 55
4.3.6 Intel TXT (LT) Configuration........................................................................... 56
4.3.7 USB Configuration........................................................................................... 57
Page V
4.3.8 F81216 Super IO Configuration...................................................................... 59
4.3.8.1 Serial Port n Configuration....................................................................... 59
4.3.8.1.1 Serial Port 1 Configuration................................................................ 60
4.3.8.1.2 Serial Port 2 Configuration................................................................ 60
4.3.8.1.3 Serial Port 3 Configuration................................................................ 61
4.3.9 H/W Monitor.................................................................................................... 63
4.3.10 Serial Port Console Redirection.................................................................... 65
4.4 IEI FEATURE ............................................................................................................. 66
4.5 CHIPSET ................................................................................................................... 67
4.5.1 Northbridge Configuration.............................................................................. 68
4.5.2 Southbridge Configuration .............................................................................. 69
4.5.3 Integrated Graphics......................................................................................... 72
4.5.4 ME Subsystem.................................................................................................. 74
4.6 BOOT........................................................................................................................ 75
AFL2-15A-H61
4.7 SECURITY................................................................................................................. 77
4.8 SAVE & EXIT............................................................................................................ 78
5 SOFTWARE DRIVERS.............................................................................................. 80
5.1 AVAILABLE SOFTWARE DRIVERS.............................................................................. 81
5.2 ST ARTING THE DRIVER PROGRAM ............................................................................ 81
5.3 CHIPSET DRIVER INSTALLATION............................................................................... 82
5.4 GRAPHICS DRIVER INSTALLATION............................................................................ 86
5.5 LAN DRIVER INSTALLATION.................................................................................... 90
5.6 AUDIO DRIVER INSTA LLATION ................................................................................. 92
5.7 TOUCH SCREEN DRIVER........................................................................................... 95
5.7.1 Calibrating the Touch Screen........................................................................... 98
5.8 WI-FI DRIVER INSTALLATION................................................................................. 100
5.9 USB 3.0 DRIVER INSTALLATION ............................................................................ 104
6 SYSTEM MONITORING: ICMC........................................................................... 107
6.1 IEI COOLING MANAGEMENT CONSOLE (ICMC) .................................................... 108
6.1.1 iCMC Installation .......................................................................................... 108
6.2 ICMC OVERVIEW....................................................................................................111
6.2.1 Information Panel...........................................................................................111
6.2.2 Chart Panel.....................................................................................................114
Page VI
AFL2-15A-H61
7 SYSTEM MAINTENANCE ......................................................................................116
7.1 SYSTEM MAINTENANCE INTRODUCTION .................................................................117
7.2 ANTI-STATIC PRECAUTIONS.....................................................................................117
7.3 TURN OFF THE POWER.............................................................................................118
7.4 OPENING THE SYSTEM.............................................................................................118
7.4.1 Removing the Back Cover...............................................................................118
7.4.2 Removing the Internal Aluminum Cover.........................................................119
7.5 REPLACING COMPONENTS...................................................................................... 120
7.5.1 Memory Module Replacement ....................................................................... 120
7.5.2 WLAN Card Replacement.............................................................................. 122
7.6 REINST ALLING THE COVERS................................................................................... 124
8 INTERFACE CONNECTORS................................................................................. 125
8.1 PERIPHERAL INTERFACE CONNECTORS................................................................... 126
8.2 INTERNAL PERIPHERAL CONNECTORS .................................................................... 127
8.2.1 Auto-dimming Connector (JP7)..................................................................... 128
8.2.2 Battery Connector (BAT2)............................................................................. 128
8.2.3 Bluetooth USB Connector (BLUETOOTH1)................................................. 129
8.2.4 EC Debug Connector (CN15)........................................................................ 129
8.2.5 Fan Connector (CPU_FAN1)......................................................................... 129
8.2.6 HDD Connector (JSATA3)............................................................................. 130
8.2.7 Hot Key LED Connector (HOTKEYLEDCN1).............................................. 130
8.2.8 Hot Key Connector (HOTKEYCN1).............................................................. 130
8.2.9 LED Indicator Connector (LEDCN1)............................................................ 131
8.2.10 Logo LED Connector (LOGO_LED)........................................................... 131
8.2.11 LVDS Connector (LVDS1) ........................................................................... 131
8.2.12 LVDS Backlight Connector (INVERTER1).................................................. 132
8.2.13 Microphone Connector (DMIC1)................................................................ 132
8.2.14 Mini USB Connector (MINUSB1) ............................................................... 133
8.2.15 Mini USB Connector (MINUSB2) ............................................................... 133
8.2.16 Power Button Connector (PW_BT1) ........................................................... 133
8.2.17 RFID USB Connector (RFIDUSB1)............................................................ 134
8.2.18 SATA Connector (SATA1)............................................................................. 134
8.2.19 SATA Power Connector (CN8)..................................................................... 134
8.2.20 Speaker Connector (SPK_CN13)................................................................. 135
Page VII
8.2.21 SPI Flash Connector (JSPI1)....................................................................... 135
8.2.22 EC SPI Flash Connector (JSPI2) ................................................................ 135
8.2.23 Touch Panel Connector (TS1)...................................................................... 136
8.2.24 TPM Connector (TPM1).............................................................................. 136
8.2.25 Type K Thermocouple Connector (CN13, CN14) ........................................ 137
8.2.26 Webcam Connector (WEBCAMER1) ........................................................... 137
8.3 EXTERNAL INTERFACE PANEL CONNECTORS .......................................................... 137
8.3.1 Audio Mic-in Jack (MIC1)............................................................................. 138
8.3.2 Audio Lline-out Jack (LINE_OUT1).............................................................. 138
8.3.3 Ethernet Connector (LAN2)........................................................................... 138
8.3.4 HDMI Connector (HDMI1)........................................................................... 139
8.3.5 Power Connector (PWR1) .......................................................................... 139
8.3.6 RS-232 Serial Ports (COM1, COM2)............................................................ 139
8.3.7 RS-422/485 Serial Port (COM3) ................................................................... 140
AFL2-15A-H61
8.3.8 USB 2.0 Connectors (USB01)........................................................................ 140
8.3.9 USB 2.0 Connector (USB23) ......................................................................... 141
8.3.10 USB 3.0 Connectors (USB3_12).................................................................. 141
8.3.1 1 VGA Connector (VGA1)............................................................................... 141
8.4 JUMPER SETTINGS .................................................................................................. 142
8.4.1 LVDS Panel Voltage Selection Jumper (DJ2)................................................ 142
8.4.2 LVDS Panel Jumper (DPANEL1)................................................................... 142
A SAFETY PRECAUTIONS....................................................................................... 143
A.1 SAFETY PRECAUTIONS .......................................................................................... 144
A.1.1 General Safety Precautions........................................................................... 144
A.1.2 CPU Temperature Warning ........................................................................... 145
A.1.3 Anti-static Precautions.................................................................................. 145
A.1.4 Product Disposal........................................................................................... 146
A.2 MAINTENANCE AND CLEANING PRECAUTIONS...................................................... 146
A.2.1 Maintenance and Cleaning............................................................................ 146
A.2.2 Cleaning Tools............................................................................................... 147
B BIOS MENU OPTIONS........................................................................................... 148
C ONE KEY RECOVERY........................................................................................... 151
C.1 ONE KEY RECOVERY INTRODUCTION .................................................................... 152
Page VIII
AFL2-15A-H61
C.1.1 System Requirement ...................................................................................... 153
C.1.2 Supported Operating System......................................................................... 154
C.2 SETUP PROCEDURE FOR WINDOWS........................................................................ 155
C.2.1 Hardware and BIOS Setup ............................................................................ 156
C.2.2 Create Partitions........................................................................................... 156
C.2.3 Install Operating System, Drivers and Applications..................................... 160
C.2.4 Building the Recovery Partition.................................................................... 161
C.2.5 Create Factory Default Image ...................................................................... 163
C.3 AUTO RECOVERY SETUP PROCEDURE.................................................................... 168
C.4 SETUP PROCEDURE FOR LINUX.............................................................................. 173
C.5 RECOVERY TOOL FUNCTIONS ................................................................................ 176
C.5.1 Factory Restore............................................................................................. 178
C.5.2 Backup System............................................................................................... 179
C.5.3 Restore Your Last Backup.............................................................................. 180
C.5.4 Manual .......................................................................................................... 181
C.6 RESTORE SYSTEMS FROM A LINUX SERVER THROUGH LAN.................................. 182
C.6.1 Configure DHCP Server Settings.................................................................. 183
C.6.2 Configure TFTP Settings............................................................................... 184
C.6.3 Configure One Key Recovery Server Settings............................................... 185
C.6.4 Start the DHCP, TFTP and HTTP................................................................. 186
C.6.5 Create Shared Directory................................................................................ 186
C.6.6 Setup a Client System for Auto Recovery...................................................... 187
C.7 OTHER INFORMATIO N ............................................................................................ 190
C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller ...................... 190
C.7.2 System Memory Requirement........................................................................ 192
D HAZARDOUS MATERIALS DISCLOSURE....................................................... 193
D.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CER TIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 194
Page IX
AFL2-15A-H61
List of Figures
Figure 1-1: AFL2-15A-H61 Flat Bezel Panel PC...........................................................................2
Figure 1-2: Front View....................................................................................................................5
Figure 1-3: LED Indicators.............................................................................................................5
Figure 1-4: Function Keys .............................................................................................................7
Figure 1-5: Rear View.....................................................................................................................8
Figure 1-6: Bottom Panel...............................................................................................................9
Figure 1-7: Side Panels................................................................................................................10
Figure 1-8: AFL2-15A-H61 Dimensions (mm) ............................................................................11
Figure 3-1: HDD Cover Retention Screws..................................................................................22
Figure 3-2: HDD Bracket Removal..............................................................................................22
Figure 3-3: Inserting the HDD......................................................................................................23
Figure 3-4: Securing the HDD......................................................................................................23
Figure 3-5: CF Card Location......................................................................................................24
Figure 3-6: Insert CF Card ...........................................................................................................24
Figure 3-7: Back Cover Retention Screws.................................................................................25
Figure 3-8: Internal Cover Retention Screws.............................................................................25
Figure 3-9: RFID Reader Module Installation.............................................................................26
Figure 3-10: RFID Reader Connection........................................................................................26
Figure 3-11: AT/ATX Switch Location.........................................................................................27
Figure 3-12: Clear CMOS Switch Location.................................................................................28
Figure 3-13: Reset Button Location............................................................................................28
Figure 3-14: Wall-mounting Bracket...........................................................................................30
Figure 3-15: Chassis Support Screws........................................................................................32
Figure 3-16: Secure the Panel PC...............................................................................................32
Figure 3-17: Arm Mounting Retention Screw Holes..................................................................33
Figure 3-18: Arm Mounting (ARM-11-RS)...................................................................................34
Figure 3-19: Stand Mounting (Stand-A/Bxx)..............................................................................35
Figure 3-20: Audio Connector.....................................................................................................36
Figure 3-21: HDMI Connection....................................................................................................37
Figure 3-22: LAN Connection......................................................................................................38
Figure 3-23: DB-9 Serial Port Connector....................................................................................39
Page X
AFL2-15A-H61
Figure 3-24: RJ-45 Serial Port Connector..................................................................................40
Figure 3-25: Type K Temperature Sensor Installation..............................................................41
Figure 3-26: USB Device Connection.........................................................................................42
Figure 3-27: VGA Connector .......................................................................................................43
Figure 5-1: Drivers........................................................................................................................82
Figure 5-2: Chipset Driver Screen...............................................................................................83
Figure 5-3: Chipset Driver Welcome Screen..............................................................................83
Figure 5-4: Chipset Driver License Agreement.........................................................................84
Figure 5-5: Chipset Driver Read Me File ....................................................................................85
Figure 5-6: Chipset Driver Setup Operations ............................................................................85
Figure 5-7: Chipset Driver Installation Finish Screen...............................................................86
Figure 5-8: Graphics Driver Read Me File..................................................................................87
Figure 5-9: Graphics Driver Setup Files Extracted ...................................................................87
Figure 5-10: Graphics Driver Welcome Screen.........................................................................88
Figure 5-11: Graphics Driver License Agreement.....................................................................88
Figure 5-12: Graphics Driver Read Me File................................................................................89
Figure 5-13: Graphics Driver Setup Operations........................................................................89
Figure 5-14: Graphics Driver Installation Finish Screen ..........................................................90
Figure 5-15: LAN Driver Welcome Screen .................................................................................91
Figure 5-16: LAN Driver Ready to Install Screen.......................................................................91
Figure 5-17: LAN Driver Setup Status Screen...........................................................................92
Figure 5-18: LAN Driver Installation Complete..........................................................................92
Figure 5-19: Audio Driver Welcome Screen...............................................................................93
Figure 5-20: Audio Driver Installation.........................................................................................94
Figure 5-21: Audio Driver Installation Complete.......................................................................94
Figure 5-22: Touch Screen Driver Welcome Screen.................................................................95
Figure 5-23: Touch Screen Driver License Agreement.............................................................96
Figure 5-24: Touch Screen Driver Choose Install Location.....................................................96
Figure 5-25: Touch Screen Driver Installation Screen..............................................................97
Figure 5-26: Touch Screen Driver Update Complete................................................................97
Figure 5-27: PenMount Monitor Icon..........................................................................................98
Figure 5-28: PenMount Monitor Popup Menu............................................................................98
Figure 5-29: Configuration Screen..............................................................................................99
Figure 5-30: Calibration Initiation Screen..................................................................................99
Figure 5-31: Calibration Screen ............................................................................................... 100
Page XI
Figure 5-32: License Agreement.............................................................................................. 100
Figure 5-33: Setup Type............................................................................................................ 101
Figure 5-34: Configuration Tool............................................................................................... 102
Figure 5-35: Ready to Install the Program.............................................................................. 102
Figure 5-36: Setup Status ......................................................................................................... 103
Figure 5-37: Installation Complete........................................................................................... 103
Figure 5-38: USB 3.0 Driver Welcome Screen........................................................................ 104
Figure 5-39: USB 3.0 Driver License Agreement.................................................................... 105
Figure 5-40: USB 3.0 Driver Installation.................................................................................. 105
Figure 5-41: USB 3.0 Driver Update Complete ....................................................................... 106
Figure 6-1: Cooling Management Console Setup Wizard...................................................... 108
Figure 6-2: Select Installation Folder....................................................................................... 109
Figure 6-3: Confirm Installation ............................................................................................... 109
Figure 6-4: Installation Complete............................................................................................. 110
AFL2-15A-H61
Figure 6-5: Restart the System................................................................................................. 110
Figure 6-6: Cooling Management Console Icon..................................................................... 111
Figure 6-7: iCMC........................................................................................................................ 111
Figure 6-8: iCMC Information Panel......................................................................................... 112
Figure 6-9: iCMC – Chart Panel................................................................................................ 114
Figure 6-10: iCMC – Time Interval Adjustment....................................................................... 115
Figure 7-1: Back Cover Retention Screws.............................................................................. 119
Figure 7-2: Internal Cover Retention Screws.......................................................................... 120
Figure 7-3: Internal Components............................................................................................. 120
Figure 7-4: DDR SO-DIMM Module Installation....................................................................... 121
Figure 7-5: Removing the Antennas........................................................................................ 122
Figure 7-6: Releasing the WLAN Card..................................................................................... 123
Figure 7-7: Removing the WLAN card..................................................................................... 123
Figure 7-8: Attaching the Antennas......................................................................................... 124
Figure 8-1: Main Board Layout Diagram................................................................................. 126
Figure C-1: IEI One Key Recovery Tool Menu........................................................................ 152
Figure C-2: Launching the Recovery Tool.............................................................................. 157
Figure C-3: Recovery Tool Setup Menu .................................................................................. 157
Figure C-4: Command Prompt ................................................................................................. 158
Figure C-5: Partition Creation Commands.............................................................................. 159
Figure C-6: Launching the Recovery Tool.............................................................................. 161
Page XII
AFL2-15A-H61
Figure C-7: Manual Recovery Environment for Windows..................................................... 161
Figure C-8: Building the Recovery Partition........................................................................... 162
Figure C-9: Press Any Key to Continue.................................................................................. 162
Figure C-10: Press F3 to Boot into Recovery Mode............................................................... 163
Figure C-11: Recovery Tool Menu ........................................................................................... 163
Figure C-12: About Symantec Ghost Window........................................................................ 164
Figure C-13: Symantec Ghost Path ......................................................................................... 164
Figure C-14: Select a Local Source Drive ............................................................................... 165
Figure C-15: Select a Source Partition from Basic Drive ...................................................... 165
Figure C-16: File Name to Copy Image to ............................................................................... 166
Figure C-17: Compress Image.................................................................................................. 166
Figure C-18: Image Creation Confirmation............................................................................. 167
Figure C-19: Image Creation Complete................................................................................... 167
Figure C-20: Image Creation Complete................................................................................... 167
Figure C-21: Press Any Key to Continue................................................................................ 168
Figure C-22: Auto Recovery Utility.......................................................................................... 169
Figure C-23: Disable Automatically Restart............................................................................ 169
Figure C-24: Launching the Recovery Tool............................................................................ 170
Figure C-25: Auto Recovery Environment for Windows ....................................................... 170
Figure C-26: Building the Auto Recovery Partition................................................................ 171
Figure C-27: Factory Default Image Confirmation ................................................................. 171
Figure C-28: Image Creation Complete................................................................................... 172
Figure C-29: Press any key to continue.................................................................................. 172
Figure C-30: Partitions for Linux.............................................................................................. 174
Figure C-31: Manual Recovery Environment for Linux ......................................................... 175
Figure C-32: Access menu.lst in Linux (Text Mode).............................................................. 175
Figure C-33: Recovery Tool Menu ........................................................................................... 176
Figure C-34: Recovery Tool Main Menu.................................................................................. 177
Figure C-35: Restore Factory Default...................................................................................... 178
Figure C-36: Recovery Complete Window.............................................................................. 178
Figure C-37: Backup System.................................................................................................... 179
Figure C-38: System Backup Complete Window ................................................................... 179
Figure C-39: Restore Backup................................................................................................... 180
Figure C-40: Restore System Backup Complete Window..................................................... 180
Figure C-41: Symantec Ghost Window ................................................................................... 181
Page XIII
Figure C-42: Disable Automatically Restart............................................................................ 188
AFL2-15A-H61
Page XIV
AFL2-15A-H61
List of Tables
Table 1-1: AFL2-15A-H61 Model Variations .................................................................................3
Table 1-2: LED Indicators ..............................................................................................................7
Table 1-3: Function Key Descriptions..........................................................................................8
Table 1-4: System Specifications................................................................................................13
Table 4-1: BIOS Navigation Keys................................................................................................46
Table 6-1: iCMC Information Panel Description..................................................................... 113
Table 8-1: Peripheral Interface Connectors............................................................................ 128
Table 8-2: Auto-dimming Connector (JP3) Pinouts............................................................... 128
Table 8-3: Battery Connector (BAT2) Pinouts........................................................................ 128
Table 8-4: Bluetooth USB Connector (BLUETOOTH1) Pinouts............................................ 129
Table 8-5: EC Debug Connector (CN15) Pinouts.................................................................... 129
Table 8-6: Fan Connector (CPU_FAN1) Pinouts..................................................................... 129
Table 8-7: HDD Connector (JSTAT3) Pinouts......................................................................... 130
Table 8-8: Hotkey LED Connector (HOTKEYLEDCN1) Pinouts............................................ 130
Table 8-9: Hotkey Connector (HOTKEYCN1) Pinouts............................................................ 130
Table 8-10: LED Indicator Connector (LEDCN1) Pinouts...................................................... 131
Table 8-11: Logo LED Connector ( LOGO_LED ) Pinouts..................................................... 131
Table 8-12: LVDS Connector (LVDS1) Pinouts....................................................................... 132
Table 8-13: LVDS Backlight Connector (INVERTER1) Pinouts............................................. 132
Table 8-14: Microphone Connector (DMIC1) Pinouts ............................................................ 132
Table 8-15: Mini USB Connector (MINUSB1) Pinouts............................................................ 133
Table 8-16: Mini USB Connector (MINUSB2) Pinouts............................................................ 133
Table 8-17: Power Button Connector (PW_BT1) Pinouts...................................................... 133
Table 8-18: RFID USB Connector (RFID_USB1) Pinouts....................................................... 134
Table 8-19: SATA Connector (SATA1) Pinouts ...................................................................... 134
Table 8-20: SATA Power Connector (CN8) Pinouts............................................................... 134
Table 8-21: Speaker Connector (SPK_CN13) Pinouts ........................................................... 135
Table 8-22: SPI Flash Connector (JSPI1) Pinouts.................................................................. 135
Table 8-23: EC SPI Flash Connector (JSPI2) Pinouts............................................................ 135
Table 8-24: Touch Panel Connector (TS1) Pinouts................................................................ 136
Table 8-25: TPM Connector (TPM1) Pinouts........................................................................... 136
Page XV
Table 8-26: Type K Thermocouple Connector (CN13, CN14) Pinouts.................................. 137
Table 8-27: Webcam Connector (WEBCAMER1) Pinouts...................................................... 137
Table 8-28: Rear Panel Connectors......................................................................................... 138
Table 8-29: Audio Mic-in Jack (MIC1) Pinouts........................................................................ 138
Table 8-30: Audio Lline-out Jack (LINE_OUT1) Pinouts........................................................ 138
Table 8-31: Ethernet Connector (LAN2) Pinouts.................................................................... 138
Table 8-32: HDMI Connector (HDMI1) Pinouts........................................................................ 139
Table 8-33: Power Connector (PWR1) Pinouts....................................................................... 139
Table 8-34: RS-232 Serial Ports (COM1, COM2) Pinouts....................................................... 139
Table 8-35: RS-422/485 Serial Port (COM3) Pinouts .............................................................. 140
Table 8-36: DB-9 Connector Pinout......................................................................................... 140
Table 8-37: USB 2.0 Connectors (USB01) Pinouts................................................................. 140
Table 8-38: USB 2.0 Connector (USB023) Pinouts................................................................. 141
Table 8-39: USB 3.0 Connectors (USB3_12) Pinouts............................................................. 141
AFL2-15A-H61
Table 8-40: VGA Connector (VGA1) Pinouts .......................................................................... 141
Table 8-41: Jumpers.................................................................................................................. 142
Table 8-42: LVDS Voltage Selection Jumper (DJ2) Settings................................................. 142
Table 8-43: LVDS Panel Jumper (DPANEL1) Settings........................................................... 142
Page XVI
AFL2-15A-H61
List of BIOS Menus
BIOS Menu 1: Main.......................................................................................................................47
BIOS Menu 2: Advanced..............................................................................................................49
BIOS Menu 3: ACPI Configuration..............................................................................................50
BIOS Menu 4: RTC Wake Settings..............................................................................................51
BIOS Menu 5: TPM Configuration...............................................................................................52
BIOS Menu 6: CPU Configuration...............................................................................................53
BIOS Menu 7: CPU Configuration...............................................................................................54
BIOS Menu 8: IDE Configuration.................................................................................................55
BIOS Menu 9: Intel TXT(LT) Configuration ................................................................................56
BIOS Menu 10: USB Configuration.............................................................................................57
BIOS Menu 11: Super IO Configuration......................................................................................59
BIOS Menu 12: Serial Port n Configuration Menu.....................................................................59
BIOS Menu 13: Hardware Health Configuration........................................................................63
BIOS Menu 14: Serial Port Console Redirection.......................................................................65
BIOS Menu 15: iEi Feature...........................................................................................................66
BIOS Menu 16: Chipset................................................................................................................67
BIOS Menu 17: Northbridge Chipset Configuration..................................................................68
BIOS Menu 18: Southbridge Chipset Configuration.................................................................69
BIOS Menu 19: Integrated Graphics...........................................................................................73
BIOS Menu 20: ME Subsystem....................................................................................................74
BIOS Menu 21: Boot.....................................................................................................................75
BIOS Menu 22: Security...............................................................................................................77
BIOS Menu 23: Exit.......................................................................................................................78
BIOS Menu 24: IEI Feature........................................................................................................ 173
Page XIV
AFL2-15A-H61
Chapter
1

1 Introduction

Page 1

1.1 Overview

AFL2-15A-H61
Figure 1-1: AFL2-15A-H61 Flat Bezel Panel PC
The AFL2-15A-H61 is a 2nd Generation Intel® Core™ i7/ i5/ i3, Celeron® or Pentium® processor powered flat bezel panel PC with a rich variety of functions and peripherals. The AFL2-15A-H61 is designed for easy and simplified integration into ki osk and point-of-sale s (POS) applications.
An Intel® H61 chipset ensures optimal memory, graphics, and peripheral I/O support. The system comes with two 2.0 GB of DDR3 SO-DIMMs ensuring smooth data throughputs with reduced bottlenecks and fast sy st em access.
Three serial ports, three external USB 2.0 ports and two external USB 3.0 ports ensure simplified connectivity to a variety of external peripheral devices. Wi-Fi capabilities and one RJ-45 Ethernet connector provide the system with smooth connection to an external LAN. An optional MSR card reader can equip the system for scanning credit cards, identification cards, loyalty cards, gift cards, and more.
Page 2
AFL2-15A-H61

1.1.1 Model Variations

The model variations of the AFL2-15A-H61 Series are listed below.
Model No. Touchscreen Type Optional Features Intel® Core i5 Ser ies
AFL2-15A-H61-i5/PC-EM-R10 Projective capacitive EM card reader AFL2-15A-H61-i5/PC-MF-R10 Projective capacitive MIFARE card reader AFL2-15A-H61-i5/PC-R10 Projective capacitive N/A AFL2-15A-H61-i5/R-EM-R10 5-Wire Resistive EM card reader AFL2-15A-H61-i5/R-MF-R10 5-Wire Resistive MIFARE card reader AFL2-15A-H61-i5/R-R10 5-Wire Resistive N/A
Intel® Core i3 Ser ies
AFL2-15A-H61-i3/PC-EM-R10 Projective capacitive EM card reader AFL2-15A-H61-i3/PC-MF-R10 Projective capacitive MIFARE card reader AFL2-15A-H61-i3/PC-R10 Projective capacitive N/A AFL2-15A-H61-i3/R-EM-R10 5-Wire Resistive EM card reader AFL2-15A-H61-i3/R-MF-R10 5-Wire Resistive MIFARE card reader AFL2-15A-H61-i3/R-R10 5-Wire Resistive N/A
Intel® Pentium® G6xxT Series
AFL2-15A-H61-P/PC-EM-R10 Projective capacitive EM card reader AFL2-15A-H61-P/PC-MF-R10 Projective capacitive MIFARE card reader AFL2-15A-H61-P/PC-R10 Projective capacitive N/A AFL2-15A-H61-P/R-EM-R10 5-Wire Resistive EM card reader AFL2-15A-H61-P/R-MF-R10 5-Wire Resistive MIFARE card reader AFL2-15A-H61-P/R-R10 5-Wire Resistive N/A
Table 1-1: AFL2-15A-H61 Model Variations

1.1.2 Features

The AFL2-15A-H61 features are listed below:
Flat-bezel LCD with LED backlight  2nd Generation Intel® Core™ i7/ i5/ i3, Pentium® and Celeron® processor
Page 3
Two 204-pin DDR3 SO -DIMM slot (system max. 16GB) preinstalled with 4GB
(two 2GB) memory
Projected capacitive touchscreen and 5-wire resistive type touchscreen
supported
Wi-Fi 802.11b/g/n 2T2R high speed wireless  EM or Mifare RFID reader  Built-in 1.3-megapixel webcam with AF, AE and AWB capabilities  Built-in two 2W speakers and microphone  IP64 compliant front panel  Auto dimming control  Light fanless technology design  Type K thermalcouple temperature

1.1.3 Light Fanless Technology Design

AFL2-15A-H61
AFL2-15A-H61 series panel PCs are designed with light fanless technology. The light fanless technology utilizes type K thermocouple temperature sensor to detect environment temperature and control fan operation to enhance system stability and remote environment control. When the environment temperature is lower than default temperature setting, the fan will turn off, showing the advantage of quiet and dust free from fanless mode. While the environment temperature is higher, the smart fan will turn on to speed up heat emission. The default temperature setting can be adjusted in BIOS (see Section
4.3.9). The system can be easily implemented in working environments that require quiet and dust free, like clean rooms, indoor HMI, and hospitals.

1.2 External Overview

1.2.1 Front Panel

The front side of the AFL2-15A-H61 is a flat bezel panel TFT LCD screen surrou nded by a PC/ABS plastic frame.
Page 4
AFL2-15A-H61
Figure 1-2: Front View
1.2.1.1 LED Indicators
There are several LED indicators located along the bottom of the LCD screen (Figure 1-3).
Figure 1-3: LED Indicators
The descriptions of each LED indicator are listed below.
Page 5
LED Indicator Description
AFL2-15A-H61
Power
AT/ATX Mode
CPU Temperature Alert
Wi-Fi
RFID
Bluetooth
Off: power cord not attached or power supply failure Blinking amber: the system is connected to a power
source and is ready to be turned on. Solid blue: the system is turned on.
Power on/off by the hot keys. See
AT: the system is in AT power mode ATX: the system is in ATX power mode
Controlled by the AT/ATX power mode switch.
Blue: CPU temperature is normal. Red: CPU temperature is at or over 80ºC.
On: the Wi-Fi module is enabled Off: the Wi-Fi module is disabled.
Controlled by the BIOS. See Section
On: the optional RFID reader is enabled Off: the optional RFID reader is disabled.
Controlled by the hot keys. See
On: the Bluetooth module is enabled Off: the Bluetooth module is disabled.
Controlled by the BIOS. See Section
Table 1-3
4.5.2
Table 1-3
4.5.2
Page 6
Auto-Dimming
Microphone
Audio Mute
Mini USB
Function
On: the auto-dimming function is enabled Off: the auto-dimming function is disabled.
Hold down Fn key for 3 seconds to enable/disable auto-dimming function or control via BIOS setting (see Section
On: the microphone is enabled Off: the microphone is disabled.
Controlled by the BIOS. See Section
On (solid red): the audio is turned off Off: the audio is turned on
Controlled by the hot keys. See
On: the Mini USB 2.0 module is enabled Off: the Mini USB 2.0 module is disabled.
Controlled by the hot keys. See
Shows the status of the function keys below the LED
4.5.2).
4.5.2
Table 1-3
Table 1-3
AFL2-15A-H61
LED Indicator Description LCD On/Off Audio Volume Down Audio Volume Up Brightness Down Brightness Up Table 1-2: LED Indicators
indicators. Blinks when the corresponding button is pushed.
WARNING:
When the CPU temperature is at or over 80ºC, the CPU temperature alert LED shows in red. If the alert LED turns red, the user must lower the environments temperature or close some running applications to cool down the CPU.
1.2.1.2 Function Keys
The function keys are located under the bottom right hand corner of the LCD screen (
Figure 1-4).
Figure 1-4: Function Keys
Page 7
The function keys are described in Table 1-3:
Key Combination Function Key Description
AFL2-15A-H61
Fn
Fn + LCD On/Off Fn + Audio Volume Down Fn + Audio Volume Up Fn + Brightness Down Fn + Brightness Up
Fn: The function key can maintain for 2 seconds.
Table 1-3: Function Key Descriptions
Hold down Fn key for 3 seconds to enable/disable auto-dimming function.
Enable/Disable RFID Mute audio Enable/Disable camera Enable/Disable Mini USB or microSD Power On/Off
Note: To power on the system, hold down the Fn + Brightness Up buttons for six seconds. To power down the system, hold down the Fn + Brightness Up buttons for six seconds.

1.2.2 Rear Panel

The rear panel provides access to retention screw holes that support VESA mounting. The
Page 8
HDD bay and CF slot are protected by the HDD cover. Refer to
Figure 1-5: Rear View
Figure 1-5.
AFL2-15A-H61

1.2.3 Bottom Panel

The bottom panel of the AFL2-15A-H61 has the following connectors and switches (
Figure 1-6):
1 x AT/ATX switch  1 x Clear CMOS switch  1 x 9V ~ 36V DC input power jack  6 x Function keys  1 x HDMI port  1 x Power button  1 x Reset button  2 x RS-232 DB-9 connectors  1 x RS-422/485 RJ-45 connector  1 x Type K thermocouple connector  2 x USB 2.0 connectors  2 x USB 3.0 connectors  1 x VGA port
Figure 1-6: Bottom Panel
Page 9

1.2.4 Side Panels

The side panels of the AFL2-15A-H61 have the following features (Figure 1-7):
2 x Audio jacks (Line-out, Mic-in)  1 x RJ-45 LAN connector  1 x USB 2.0 connector  1 x Temperature sensor (left side panel)
AFL2-15A-H61
Figure 1-7: Side Panels

1.3 Dimensions

The AFL2-15A-H61 dimensions are shown below.
Width: 363.2 mm  Height: 305.1 mm  Depth: 58.8 mm
Page 10
AFL2-15A-H61
Figure 1-8: AFL2-15A-H61 Dimensions (mm)

1.4 Internal Overview

The AFL2-15A-H61 has the following components installed internally:
1 x Motherboard  2 x 2.0 GB 1333 MHz DDR3 SO-DIMMs  1 x 802.11 b/g/n wireless LAN module
Page 11
AFL2-15A-H61

1.5 System Specifications

The technical specifications for the AFL2-15A-H61 systems are listed in Table 1-4.
Specification AFL2-15A-H61 LCD Size 15" (4:3) Max. Resolution 1024 (W) x 768 (H) Brightness (cd/m2) 400 Contrast Ratio 700:1 LCD Color 16.2M Pixel Pitch (H x V) (mm) 0.297(H) x 0.297 (V) Viewing Angle (H-V) 160° / 140° Backlight MTBF (hr) 50,000 Touchscreen 5-Wire resistive type touch screen (R models only)
Projected capacitive type touch screen (PC models only)
CPU 2nd Generation Intel® Core™ i7/ i5/ i3, Pentium® or Celeron®
processor
Chipset Intel® H61 Ethernet Realtek RTL8111E PCIe GbE controller support ASF2.0 Memory Preinstalled two 204-pin 2 GB DDR3 SO-DIMM (max. 16G) Expansion 1 x PCIe Mini slot for Wi-Fi module
1 x PCIe Mini slot reserved
SSD CF Type II socket HDD 2.5" SATA 3Gb /s HDD bay Audio Realtek ALC892 HD Audio codec (Line-out, Mic-in) Speaker AMP 2 W + 2 W (built-in stereo speakers) Camera 1.3 M pixels with low light function Wireless 1 x Wireless LAN 802.11 b/g/n module (PCIe Mini card) Bluetooth Optional internal USB interface, Bluetooth V2.0+EDR RFID Reader EM 125 KHz or MIFARE 13.56 MHz card reader (optional) MSR Card Reader MSR card reader (optional) OSD Function LCD on/off, brightness up/down, volume up/down, Hot Key Construction Material PC + ABS plastic front frame Mounting VESA 100 mm x 100 mm (Wall, Stand or Arm)
Page 12
AFL2-15A-H61
Front Panel Color Black Weight (N/G) 5.2 kg / 7.3 kg Dimensions (W x H x D) (mm) 363.2 x 305.1 x 58.8 Operating Temperature -20ºC ~ 50ºC Storage Temperature -20ºC ~ 60ºC Humidity 10% ~ 95% (no-condensing) IP level IP 64 compliant front panel Power Supply 90W power adapter Input: 100V AC ~ 240V AC @ 50 / 60 Hz Output: 19V DC Power Requirement 9V ~ 36V DC Power Consumption 19V@3.42A (Intel® Core™ i3-2100T CPU with 4GB 1333 MHz
DDR3 memory)
I/O Ports and Switches 2 x RS-232 (DB-9 connector) 1 x GbE LAN (RJ-45 connector) on left side 1 x RS-422/485 (RJ-45 connector) 3 x USB 2.0 connectors (two on bottom side, one on left side) 2 x USB 3.0 connectors 1 x Mini USB 2.0 connector (on front panel) 1 x microSD card slot (on front panel) 2 x Audio jacks (line-out, MIC) 1 x VGA port (DB15 connector) 1 x HDMI port 1 x Power switch 1 x AT/ATX switch 1 x Reset button 1 x Clear CMOS button 1 x 9 V ~ 36 V DC input jack
Table 1-4: System Specifications
Page 13
AFL2-15A-H61
Chapter
2

2 Unpacking

Page 14
AFL2-15A-H61

2.1 Unpacking

To unpack the flat bezel panel PC, follow the steps below:
WARNING!
The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the flat bezel panel PC has been properly installed. This ensures the screen is protected during the installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the flat bezel panel PC.
Step 7: Make sure all the components listed in the pa cking list are present. Step 0:

2.1.1 Packing List

The AFL2-15A-H61 flat bezel panel PC is shipped with the following components:
Quantity Item Image Standard
1 AFL2-15A-H61 panel PC
Page 15
1 Power adapter
(P/N: 63040-010090-020-RS)
1 Power cord
AFL2-15A-H61
(P/N: 32702-000401-100-RS)
1 Power transfer cord
(P/N: 32702-000300-100-RS)
1 RJ-45 to DB-9 COM Port Cable
(P/N: 32005-000200-200-RS)
1 OSD Remote Control
(P/N: 7Z000-SLPCB005-RS)
1 Temperature sensor cable
(P/N: 32133-004300-100-RS)
Page 16
1 Pen for resistive touchscreen
(P/N: 43125-0002C0-00-RS)
4 M3 screw pack
(P/N: 44013-030041-RS)
4 M4 screw pack
(P/N: 44033-040061-RS)
1 Utility CD
1 One Key Recovery CD
(P/N: 7B000-000724-RS)
AFL2-15A-H61
Optional
Wall mounting kit (P/N: AFL WK-19/AFL WK-19B)
Arm (P/N: ARM-1 1-RS/ARM-31-RS)
Stand (P/N: STAND-A19/ STAND-B19/ STAND-C19/ STAND-210-R11)
Hybrid Card Reader (P/N: AFL2P-12AMSI-U-R10)
Magnetic Stripe Reader (P/N: AFL2P-12AMSR-U-R10)
Bluetooth Module Kit (P/N: AFL2-BT-KIT01-R11) OS: Win CE 6.0 (128MB CF Card) (P/N: AFL2CF-15A-H61-CE060-128M-R10) OS: Win XPE (2GB CF Card) (P/N: AFL2CF-15A-H61-XPE-2G-R10) OS: Win XPE (4GB CF Card) (P/N: AFL2CF-15A-H61-XPE-4G-R10)
Page 17
AFL2-15A-H61
OS: Linux (2GB CF Card) (P/N: AFL2CF-15A-H61-LNX-2G-R10) OS: Win 7 Embedded (4GB CF Card) (P/N: AFL2CF-15A-H61-WES7P-4G-R10
AFL2CF-15A-H61-WES7E-4G-R10)
If any of these items are missing or damaged, contact the distributor or sales representative immediately.
Page 18
AFL2-15A-H61

3 Installation

Chapter
3
Page 19

3.1 Anti-static Precautions

WARNING:
Failure to take ESD precautions during the maintenance of the AFL2-15A-H61 may result in permanent damage to the AFL2-15A-H61 and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL2-15A-H61. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the AFL2-15A-H61 is accessed internally, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
AFL2-15A-H61
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: - Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.
Use an anti-static pad: - When configuring the AFL2 -15A-H61, place it on an
antic-static pad. This reduces the possibility of ESD damaging the AFL2-15A-H61.
Only handle the edges of the PCB: - When handling the PCB, hold the PCB
by the edges.

3.2 Installation Precautions

When installing the flat bezel panel PC, please follow the precautions listed below:
Power turned off: When installing the flat bezel panel PC, make sure the
power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system.
Page 20
Certified Engineers: Only certified engineers should install and modify
onboard functionalities.
AFL2-15A-H61
Anti-static Discharge : If a user open the rear p anel of the flat bezel panel PC,
to configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband.

3.3 Installation and Configuration Steps

The following installation steps must be followed.
Step 1: Unpack the flat bezel panel PC.
Step 2: Install the HDD.
Step 3: Install the CF card.
Step 4: Install the RFID reader. (optional)
Step 5: Configure the system.
Step 6: Connect peripheral devices to the flat bezel panel PC.
Step 7: Mount the flat bezel panel PC. Step 0:

3.4 HDD Installation

WARNING:
Over-tightening back cover screws will crack the plastic frame. Maximum torque for cover screws is 5 kg-cm (0.36 lb-ft/0.49 Nm).
To install the HDD into the AFL2-15A-H61, please follow the steps below:
Step 1: Remove two (2) retention screws from the HDD cover (
Figure 3-1).
Page 21
AFL2-15A-H61
Figure 3-1: HDD Cover Retention Screws
Step 2: Remove the HDD cover from the device.
Step 3: Loosen the captive screw to release the HDD bracket from the chassis. Slide the
HDD bracket out of the device as shown (
Figure 3-2: HDD Bracket Removal
Figure 3-2).
Page 22
Step 4: Insert an HDD into the bracket as shown (
Figure 3-3).
AFL2-15A-H61
Figure 3-3: Inserting the HDD
Step 5: Secure the HDD to the bracket using four (4) retention screws (two screws on
each side) (
Figure 3-4: Securing the HDD
Step 6: Slide the HDD module back into the device.
Figure 3-4).
Step 7: Tighten the captive screw.
Step 8: Replace the HDD cover and secure it using two (2) retention screws. Step 0:
Page 23

3.5 CF Card Installation

The AFL2-15A-H61 has one CF Type II slot under the HDD bay. To install the CF card, follow the instructions below.
AFL2-15A-H61
Step 1: Remove two (2) retention screws from the HDD cover (
Step 2: Remove the HDD cover from the device.
Step 3: Locate the CF slot (
Figure 3-5: CF Card Location
Step 4: Insert a CF card into the slot (
Figure 3-5).
Figure 3-6).
Figure 3-1).
Page 24
Figure 3-6: Insert CF Card
Step 5: Replace the HDD cover and secure it using two (2) retention screws. Step 0:
AFL2-15A-H61

3.6 RFID Reader Installation (Optional)

An optional RFID reader can be installed in the AFL2-15A-H61. To install the RFID reader, follow the instructions below.
Step 1: Remove a total of ten (10) retention screws from the back cover (
Figure 3-7).
Figure 3-7: Back Cover Retention Screws
Step 2: Remove the six (6) retention screws securing the internal aluminum cover to the
chassis (
Figure 3-8).
Figure 3-8: Internal Cover Retention Screws
Page 25
Step 3: Install the RFID reader module in the location shown in Figure 3-9 by two
retention screws.
AFL2-15A-H61
Figure 3-9: RFID Reader Module Installation
Step 4: Connect the RFID module to the RFID connector on the main board (
3-10). The RFID connector pinouts are listed in Section
Step 5: Place the RFID antenna on the location shown in
RFID antenna to the RFID antenna connector on the RFID module.
8.2.17.
Figure 3-10. Connect the
Figure
Page 26
Figure 3-10: RFID Reader Connection
AFL2-15A-H61
Step 6: Replace the internal cover and back cover using previously removed retention
screws. Step 0:

3.7 AT/ATX Mode Selection

AT or ATX power mode can be used on the AFL2-15A-H61. The selection is made through an AT/ATX switch located on the bottom panel. To select AT mode or ATX mode, follow the steps below.
Step 1: Locate the AT/ATX switch on the bottom panel (
Figure 3-11: AT/ATX Switch Location
Step 2: Adjust the AT/ATX switch. Step 0:
Figure 3-11).

3.7.1 AT Power Mode

With the AT mode selected, the power is controlled by a central power unit rather than a power switch. The AFL2-15A-H61 panel PC turns on automatically when the power is connected. The AT mode benefits a production line to control multiple panel PCs from a central management center and other applications including:
 ATM  Self-service kiosk  Plant environment monitoring system  Factory automation platform  Manufacturing shop flow

3.7.2 ATX Power Mode

With the ATX mode selected, the AFL2-15A-H61 panel PC goes in a standby mode when it is turned off. The panel PC can be easily turned on via network or a power switch in standby mode. Remote power control is perfect for advertising applications since the
Page 27
broadcasting time for each panel PC can be set individually and cont rolled remotely . Other possible application includes
Security surveillance Point-of-Sale (POS) Advertising terminal

3.8 Clear CMOS

If the AFL2-15A-H61 fails to boot due to improper BIOS settings, the clear CMOS switch clears the CMOS data and resets the system BIOS information. To do this, adjust the clear CMOS switch to clear CMOS mode for a few seconds then reinstall the clear CMOS switch back to keep CMOS mode.
AFL2-15A-H61
Step 1: Locate the clear CMOS switch on the bottom panel (
Figure 3-12: Clear CMOS Switch Location
Step 2: Adjust the clear CMOS switch. Step 0:

3.9 Reset the System

The reset button enables user to reboot the system when the system is turned on. To reboot the system, follow the steps below.
Step 1: Locate the reset button on the bottom panel (
Figure 3-12).
Figure 3-13).
Page 28
Figure 3-13: Reset Button Location
AFL2-15A-H61
Step 2: Press the reset button. Step 0:

3.10 Powering On the System

To power on the system, follow the steps below:
Step 1: Locate the Function and Brightness Up function keys. See Section
Step 2: Hold down the Function and Brightness Up buttons for three seconds to power
on the system. Step 0:

3.11 Powering Off the System

To power off the system, follow the steps below:
Step 1: Locate the Function and Brightness Up function keys. See Section
Step 2: Hold down the Function and Brightness Up buttons for six seconds to power off
the system. Step 0:

3.12 Mounting the System

WARNING:
1.2.1.2.
1.2.1.2.
When mounting the flat bezel panel PC onto an arm, onto the wall or onto a panel, it is better to have more than one person to help with the installation to make sure the panel PC does not fall down and get damaged.
The three methods of mounting the AFL2-15A-H61 are listed below.
Wall mounting Arm mounting Stand mounting
The three mounting methods are described below.
Page 29

3.12.1 Wall Mounting

To mount the flat bezel panel PC onto the wall, please follow the steps below.
Step 1: Select the location on the wall for the wall-mounting bracket.
Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention
screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into
AFL2-15A-H61
the four pilot holes and tightening them (
Figure 3-14).
Figure 3-14: Wall-mounting Bracket
Page 30
AFL2-15A-H61
Step 6: Insert the four monitor mounting screws provided in the wall mount kit into the
four screw holes on the real panel of the flat bezel panel PC and tighten until the screw shank is secured against the rear panel (
Figure 3-15).
WARNING:
Please use the M4 screws provided in the wall mount kit for the rear panel. If the screw is missing, the thread depth of the replacement screw should be not more than 4 mm.
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on
the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes ( Ensure that all four of the mounting screws fit snugly into their respective slotted holes.
Figure 3-15).
NOTE:
In the diagram below the bracket is already installed on the wall.
Page 31
AFL2-15A-H61
Figure 3-15: Chassis Support Screws
Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting
bracket. (
Figure 3-16).
Page 32
Figure 3-16: Secure the Panel PC
AFL2-15A-H61

3.12.2 Arm Mounting

The AFL2-15A-H61 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 100mm interface pad. To mount the AFL2-15A-H61 on an arm, please follow the steps below.
Step 1: The arm is a separately purchased item. Please correctly mount the arm onto
the surface it uses as a base. To do this, refer to the installation documentation that came with the mounting arm.
NOTE:
When purchasing the arm please ensure that it is VESA compliant and that the arm has a 100 mm interface pad. If the mounting arm is not VESA compliant it cannot be used to support the AFL2-15A-H61 flat bezel panel PC.
Step 2: Once the mounting arm has been firmly attached to the surface, lift the flat bezel
panel PC onto the interface pad of the mounting arm.
Step 3: Align the retention screw holes on the mounting arm interface with those in the
flat bezel panel PC (
Figure 3-17).
Figure 3-17: Arm Mounting Retention Screw Holes
Page 33
Step 4: Secure the AFL2-15A-H61 to the interface p ad by inserting fou r retention screws
through the mounting arm interface pad and into the AFL2-15A-H61.Step 0:
AFL2-15A-H61
Figure 3-18: Arm Mounting (ARM-11-RS)

3.12.3 Stand Mounting

To mount the AFL2-15A-H61 using the stand mounting kit, please follow the steps below.
Step 1: Locate the screw holes on the rear of the AFL2-15A-H61. This is where the
bracket will be attached.
Step 2: Align the bracket with the screw holes.
Step 3: To secure the bracket to the AFL2-15A-H61 insert the retention screws into the
screw holes and tighten them.Step 0:
Page 34
AFL2-15A-H61
Figure 3-19: Stand Mounting (Stand-A/Bxx)

3.13 External Peripheral Device Connection

The following external peripheral devices can be connected to the external peripheral interface connectors.
 Audio devices  HDMI devices  RJ-45 Ethernet cable connector  Serial port devices  USB devices  VGA monitor
To install these devices, connect the corresponding cable connector from the actual device to the corresponding AFL2-15A-H61 external peripheral interface connector making sure the pins are properly aligned.
Page 35

3.13.1 Audio Connection

The audio jacks on the external audio connector enable the AFL2-15A-H61 to be connected to a stereo sound setup. To install the audio devices, follow the steps below.
Step 1: Identify the audio plugs. The plugs on your home theater system or speakers
may not match the colors on the rear panel. If audio plugs are plugged into the wrong jacks, sound quality will be very bad.
Step 2: Plug the audio plugs into the audio jacks. Plug the audio plugs into the audio
jacks. If the plugs on your speakers are different, an adapter will need to be used to plug them into the audio jacks.
Line Out port (Lime): Connects to a head phone or a speaker.  Microphone (Pink): Connects to a microphone.
AFL2-15A-H61
Figure 3-20: Audio Connector
Step 3: Check audio clarity. Check that the sound is coming through the right speakers
by adjusting the balance front to rear and left to right.

3.13.2 HDMI Device Connection

The HDMI connector transmits a digital signal to compatible HDMI display devices such as a TV or computer screen. To connect the HDMI cable to the AFL2-15A-H61, follow the steps below.
Page 36
AFL2-15A-H61
Step 1: Locate the HDMI connector. The location is shown in Chapter 1.
Step 2: Align the connector. Alig n the HDMI connector with the HDMI port. Make sure
the orientation of the connector is correct.
Figure 3-21: HDMI Connection
Step 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector
should engage with a gentle push. If the connector does not insert easily, check again that the connector is aligned correctly, and that the connector is being inserted with the right way up.

3.13.3 LAN Connection

There is one external RJ-45 LAN connectors The RJ-45 connector enables connection to an external network. To connect a LAN cable with an RJ-45 connector, please follow the instructions below.
Step 1: Locate the RJ-45 connectors. The location of the LAN conne ctor is shown in
Chapter 1.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
Page 37
the RJ-45 connectors on the AFL2-15A-H61. See Figure 3-22.
AFL2-15A-H61
Figure 3-22: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the external interface.

3.13.4 Serial Device Connection

There are two external RS-232 DB-9 connectors and one RS-422/485 RJ-45 connector for serial device connection. Follow the steps below to connect a serial device to the AFL2-15A-H61.
3.13.4.1 DB-9 Serial Port Connection
Follow the steps below to connect a serial device to the DB-9 connector of the AFL2-15A-H61 panel PC.
Step 1: Locate the DB-9 connector. The locations of the DB-9 connectors are shown
in Chapter 1.
Page 38
AFL2-15A-H61
Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into
the DB-9 connector on the bottom panel. See
Figure 3-23.
Figure 3-23: DB-9 Serial Port Connector
Step 3: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.
3.13.4.2 RJ-45 Serial Port Connection
Follow the steps below to connect a serial device to the RJ-45 serial port connector of the AFL2-15A-H61 panel PC.
Step 1: Locate the RJ-45 serial port. The location of the RJ-45 serial port is shown in
Chapter 1.
Step 2: Connect the RJ-45 to COM port cable to the panel PC. Insert the RJ-45
connector end of cable into the RJ-45 serial port. See
Step 3: Connect the serial device. Connect a serial device to the DB-9 connector end
of the cable. See
Figure 3-24.
Figure 3-24.
Step 0:
Page 39
AFL2-15A-H61
Figure 3-24: RJ-45 Serial Port Connector
Step 4: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.

3.13.5 Type K Temperature Sensor Connection

The AFL2-15A-H61 has a type K thermocouple connector on the bottom panel. The type K connector is connected to a type K temperature sensor cable, which can be found in the packing list. To connect a type K temperature sensor cable to the AFL2-15A-H61, please follow the steps below.
Step 1: Locate the type K connector on the bottom panel. See
Step 2: Align the connectors. Align the type K connector on the type K temperature
sensor cable with the type K connector on the AFL2-15A-H61.
Step 3: Insert the temperature sensor cable type K connector. Once aligned, gently
insert the temperature sensor cable type K connector into the external interface.
Figure 3-25.
Step 0:
Page 40
AFL2-15A-H61
Figure 3-25: Type K Temperature Sensor Installation

3.13.6 USB Device Connection

NOTE:
User must install the USB 3.0 driver before connecting a USB device to the system or else the system may not recognize the connected device.
There are three USB 2.0 connectors and two USB 3.0 connectors on the AFL2-15A-H61. To connect a USB device, please follow the instructions below.
Step 1: Locate the USB connectors. The locations of the USB connectors are shown
in Chapter 1.
Step 2: Align the connectors. Align the USB device connector with one of the
connectors on the AFL2-1 5A-H61. See
Figure 3-26.
Page 41
AFL2-15A-H61
Figure 3-26: USB Device Connection
Step 3: Insert the device connector. Once aligned, gently insert the USB device
connector into the onboard connector. Step 0:

3.13.7 VGA Monitor Connection

The AFL2-15A-H61 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the AFL2-15A-H61, please follow the instructions below.
Step 1: Locate the female DB-15 connector. The location of the female DB-15
connector is shown in Chapter 1.
Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
Page 42
Step 3: Insert the VGA connector. Once the conne ctors are prop erly aligned with the
insert the male connector from the VGA screen into the female connector on the AFL2-15A-H61. See
Figure 3-27.
AFL2-15A-H61
Figure 3-27: VGA Connector
Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either side of the connector.
Page 43
AFL2-15A-H61
Chapter
4

4 BIOS Setup

Page 44
AFL2-15A-H61

4.1 Introduction

A licensed copy of the BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed.

4.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.
1. Press the DEL or F2 key as soon as the system is turned on or
2. Press the DEL or F2 key when the “Press DEL or F2 to enter SETUP” message appears on the screen. 0.
If the message disappears before the DEL or F2 key is pressed, restart the computer and try again.

4.1.2 Using Setup

Use the arrow keys to highlight items, press ENTER to select, use the PageUp and PageDown keys to change entries, press F1 for help and press E keys are shown in the following table.
Key Function
Up arrow Move to the item above Down arrow Move to the item below Left arrow Move to the item on the left hand side Right arrow Move to the item on the right hand side + Increase the numeric value or make ch anges
- Decrease the numeric value or make changes
SC to quit. Navigation
F1 key General help, only for St atus Page Setup Menu and Option
Page Setup Menu
Page 45
F2 key Load previous values. F3 key Load optimized defaults F4 key Save changes and Exit BIOS Esc key Main Menu – Quit and do n ot save ch anges into CMOS
Table 4-1: BIOS Navigation Keys

4.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the
AFL2-15A-H61
Status Page Setup Menu and Option Page Setup Menu -­Exit current page and return to Main Menu
possible selections for the highlighted item appears. To exit the Help Window press E the F1 key again.

4.1.4 Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration are made, CMOS defaults.

4.1.5 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:
Main – Changes the basic system configuration.  Advanced – Changes the advanced system settings.  Chipset – Changes the chipset settings.  Boot – Changes the system boot configuration.  Security – Sets User and Supervisor Passwords.  Save & Exit – Selects exit options and loads default settings
SC or
Page 46
The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.
AFL2-15A-H61

4.2 Main

The Main BIOS menu (9BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
BIOS Information BIOS Vendor American Megatrends Core Version 4.6.4.0 0.03 Compliency UEFI 2.0 Project Version SE16AR16.ROM Build Date and Time 08/23/2012 17:38:38
iWDD Vendor ICP iWDD Version SE16ER17.bin
Memory Information Total Memory 2048 MB (DDR3 1333)
System Date [Fri 07/19/2012] System Time [17:16:27]
Access Level Administrator
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
Set the Date. Use Tab to switch between Data elements.
----------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
BIOS Menu 1: Main
Î BIOS Information
The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information cannot be changed. The items shown in the system overview include:
BIOS Vendor: Installed BIOS vendor  Core Version: Current BIOS version  Compliency: Current compliant version  Project Version: the bo ard version  Build Date and Time: Date the current BIOS version was made
Î iWDD Vendor
The iWDD Vendor displays the installed iWDD vendor. The fields in iWDD
Vendor cannot be changed.
Page 47
Î iWDD Version
The iWDD Version displays the current iWDD version. The fields in iWDD
Version cannot be changed.
Î Memory Information
The Memory Information lists a brief summary of the on-board memory. The fields in Memory Information cannot be changed.
Total Memory: Displays the auto-detected system memory size and type.
The System Overview field also has two user configurable fields:
Î System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
AFL2-15A-H61
year.
Î System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

4.3 Advanced

Use the Advanced menu (9BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.
Page 48
ACPI Settings RTC Wake Settings Trusted Computing
AFL2-15A-H61
 CPU Configuration  SATA Configuration  Intel TXT (LT) Configuration  USB Configuration  F81216 Super IO Configuration  H/W Monitor  Serial Port Console Redirection  iEi Feature
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> ACPI Settings > RTC Wake Settings > Trusted Computing > CPU Configuration > SATA Configuration > Intel TXT(LT) Configuration > USB Configuration > F81216 Super IO Configuration > H/M Monitor > Serial Port Console Redirection > iEi Feature
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
System ACPI Parameters.
----------------------
ÅÆ
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
: Select Screen
BIOS Menu 2: Advanced

4.3.1 ACPI Settings

The ACPI Settings menu (9BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options.
Page 49
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State [S1 (CPU Stop Clock)]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 3: ACPI Configuration
Select the highest ACPI sleep state the system will enter, when the SUSPEND button is pressed.
----------------------
ÅÆ
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
AFL2-15A-H61
: Select Screen
Î ACPI Sleep State [S1 (CPU Stop Clock)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.
Î
S1 (CPU Stop Clock)
Î
S3 (Suspend to RAM)
DEFAULT
The system enters S1 (POS) sleep state. The system appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode.
The caches are flushed and the CPU is powered off. Power to the RAM is maintained. The computer returns slower to a working state, but more power is saved.

4.3.2 RTC Wake Settings

The RTC Wake Settings menu (BIOS Menu 4) configures RTC wake event.
Page 50
E
w
AFL2-15A-H61
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Wake system with Fixed Time [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
nable or disable System
ake on alarm event. When enabled, System will wake on the dat::hr::min::sec specified
----------------------
ÅÆ
: Select Screen
: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit
BIOS Menu 4: RTC Wake Settings
Î Wake System with Fixed Time [Disabled]
Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state.
Î
Disabled DEFAULT
Î
Enabled
The real time clock (RTC) cannot generate a wake event
If selected, the following appears with values that can be selected:
*Wake up every day *Wake up date *Wake up hour *Wake up minute *Wake up second After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
Page 51
E
AFL2-15A-H61

4.3.3 Trusted Computing

Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM).
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
TPM Configuration TPM SUPPORT [Disable]
Current TPM Status Information
NO TPM Hardware
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
nables or Disables TPM support. O.S. will not show TPM. Reset of platform is required.
----------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/=” Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit
BIOS Menu 5: TPM Configuration
Î TPM Support [Disable]
Use the TPM Support option to configure support for the TPM.
Î
Disable DEFAULT
Î
Enable
TPM support is disabled. TPM support is enabled.

4.3.4 CPU Configuration

Use the CPU Configuration menu (BIOS Menu 6) to enter the CPU Information submenu or enable Intel Virtualization Technology.
Page 52
AFL2-15A-H61
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Configuration
> CPU Information
Hyper-threading [Enabled] Intel Virtualization Technology [Disabled]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 6: CPU Configuration
Socket specific CPU Information
----------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Î Hyper-threading [Enabled]
Use the Hyper-threading function to enable or disable the CPU hyper threading function.
Î
Disabled
Î
Enabled DEFAULT
Î Intel Virtualization Technology [Disabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel Virtualization technology allows several OSs to run on the same system at the same time.
Î
Disabled DEFAULT
Î
Enabled
Disables the use of hyper-threading technology Enables the use of hyper-threading technology
Disables Intel Virtualization Technology. Enables Intel Virtualization Technology.
4.3.4.1 CPU Information
Use the CPU Information submenu (BIOS Menu 7) to view detailed CPU specifications and configure the CPU.
Page 53
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Socket 0 CPU Information
Intel(R) Core(TM) i3-2100T CPU @ 2.50GHz CPU Signature 206a7 Microcode Patch 25 Max CPU Speed 2500 MHz Min CPU Speed 1600 MHz Processor Cores 2 Intel HT Technology Supported Intel VT-x Technology Supported Intel SMX Technology Not Supported
L1 Data Cache 32 kB x 2 L1 Code Cache 32 kB x 2 L2 Cache 256 kB x 2 L3 Cache 3072 kB
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 7: CPU Configuration
----------------------
ÅÆ
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
AFL2-15A-H61
: Select Screen
The CPU Configuration menu (
Processor Type: Lists the brand name of the CPU being used  CPU Signature: Lists the CPU signature value.  Microcode Patch: Lists the microcode patch being used.  Max CPU Speed: Lists the maximum CPU processing speed.  Min CPU Speed: Lists the minimum CPU processing speed.  Processor Cores: Lists the number of the processor core  Intel HT Technology: Indicates if Intel HT Technology is supported by the
CPU.
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
Intel SMX Technology: Indicates if Intel SMX Technology is supported by the
CPU.
L1 Data Cache: Lists the amount of data storage space on the L1 cache.  L1 Code Cache: Lists the amount of code storage space on the L1 cache.  L2 Cache: Lists the amount of storage space on the L2 cache.
BIOS Menu 6) lists the following CPU details:
Page 54
L3 Cache: Lists the amount of storage space on the L3 cache.
AFL2-15A-H61

4.3.5 SATA Configuration

Use the SATA Configuration menu (BIOS Menu 8) to change and/or set the configuration of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
SATA Configuration
SATA Mode [IDE Mode] Serial-ATA Controller 0 [Compatible] Serial-ATA Controller 1 [Enhanced]
SATA Port0 Not Present
SATA Port1 Not Present
(1) IDE Mode. (2) AHCI Mode. (3) RAID Mode.
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 8: IDE Configuration
Î SATA Mode [IDE Mode]
Use the SATA Mode option to configure SATA devices as normal IDE devices.
Î
Disable
Î
IDE Mode DEFAULT
Î Serial-ATA Controller 0 [Compatible]
Use the Serial-ATA Controller 0 option to configure the Serial-ATA controller mode when the SATA mode is set to IDE Mode.
Î
Disabled
Î
Enhanced
Disables SATA devices. Configures SATA devices as normal IDE device.
Disables Serial-ATA controller. Configures the Serial-ATA controller to be in enhanced
mode. In this mode, IDE channels and SATA channels are separated. Some legacy OS do not support this mode.
Page 55
AFL2-15A-H61
Î
Compatible DEFAULT
Î Serial-ATA Controller 1 [Enhanced]
Use the Serial-ATA Controller 1 option to configure the Serial-ATA controller mode when the SATA mode is set to IDE Mode.
Î
Disabled
Î
Enhanced DEFAULT
Configures the Serial-ATA controller to be in compatible mode. In this mode, a SATA channel will replace one of the IDE channels.
Disables Serial-ATA controller. Configures the Serial-ATA controller to be in enhanced
mode. In this mode, IDE channels and SATA channels are separated. Some legacy OS do not support this mode.

4.3.6 Intel TXT (LT) Configuration

Use the Intel TXT (LT) Configuration menu (BIOS Menu 9) to configure Intel Trusted Execution Technology support.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel Trusted Execution Technology Configuration
Intel TXT support only can be enabled /disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT.
Secure Mode Extensions (SMX) Disabled
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 9: Intel TXT(LT) Configuration
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Page 56
AFL2-15A-H61

4.3.7 USB Configuration

Use the USB Configuration menu (BIOS Menu 10) to read USB configuration information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices: 1 Drive, 3 Hubs
USB Support [Enabled] Legacy USB Support [Enabled]
Mass Storage Device:
Generic STORAGE DEVICE 9454 [Auto]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
USB Support Parameters
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
BIOS Menu 10: USB Configuration
Î USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system
Î USB Support [Enabled]
Use the USB Support BIOS option to enable USB support.
Î
Disabled
Î
Enabled DEFAULT
Î Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all
USB support disabled USB support enabled
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
Page 57
keyboard can control the system even when there is no USB driver loaded onto the system.
AFL2-15A-H61
Î
Enabled DEFAULT
Î
Disabled
Î
Auto
Î Generic STORAGE DEVICE 9454 [Auto]
Use the Generic STORAGE DEVICE 9454 BIOS option to specify the type of emulation BIOS has to provide for the USB device.
Î
Auto DEFAULT
Î
Floppy
Î
Forced FDD
Legacy USB support enabled Legacy USB support disabled Legacy USB support disabled if no USB devices are
connected
BIOS auto-detects the current USB. The USB device will be emulated as a floppy drive.
The device can be either A: or B: responding to INT13h calls that return DL = 0 or DL = 1 respectively.
Allows a hard disk image to be connected as a
Î
Hard Disk
Î
CD-ROM
floppy image. This option works only for drives formatted with FAT12, FAT16 or FAT32.
Allows the USB device to be emulated as hard disk responding to INT13h calls that return DL values of 80h or above.
Assumes the CD-ROM is formatted as bootable media. All the devices that support block sizes greater than 512 bytes can only be booted using this option.
Page 58
S
E
AFL2-15A-H61

4.3.8 F81216 Super IO Configuration

Use the F81216 Super IO Configuration menu (BIOS Menu 11) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
F81216 Super IO Configuration
Super IO Chip Fintek F81216
> Serial Port 1 Configuration > Serial Port 2 Configuration > Serial Port 3 Configuration
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
et Parameters of Serial Port 0 (COMA)
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
BIOS Menu 11: Super IO Configuration
4.3.8.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 12) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Serial Port 0 Configuration
Serial Port [Enabled]
Device Settings IO=3F8h; IRQ=4
Change Settings [Auto]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
nable or Disable Serial Port (COM)
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
BIOS Menu 12: Serial Port n Configuration Menu
Page 59
4.3.8.1.1 Serial Port 1 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
AFL2-15A-H61
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt address.
Î
Auto DEFAULT
Î
IO=3F8h; IRQ=4
Î
IO=3F8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=2F8h; IRQ=3, 4,5,6,7,10,11,12
Disable the serial port Enable the serial port
The serial port IO port address and interrupt address are automatically detected.
Serial Port I/O port address is 3F8h and the interrupt address is IRQ4
Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Î
IO=3E8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=2E8h; IRQ=3, 4,5,6,7,10,11,12
4.3.8.1.2 Serial Port 2 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Page 60
Serial Port I/O port address is 3E8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 2E8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Disable the serial port
AFL2-15A-H61
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt address.
Î
Auto DEFAULT
Î
IO=2F8h; IRQ=3
Î
IO=3F8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=2F8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=3E8h; IRQ=3,
Enable the serial port
The serial port IO port address and interrupt address are automatically detected.
Serial Port I/O port address is 2F8h and the interrupt address is IRQ3
Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 3E8h and the
4,5,6,7,10,11,12
Î
IO=2E8h; IRQ=3, 4,5,6,7,10,11,12
4.3.8.1.3 Serial Port 3 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt address.
interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12 Serial Port I/O port address is 2E8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Disable the serial port Enable the serial port
Page 61
AFL2-15A-H61
Î
Auto DEFAULT
Î
IO=3E8h; IRQ=7
Î
IO=3F8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=2F8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=3E8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=2E8h; IRQ=3, 4,5,6,7,10,11,12
Î
IO=2E0h; IRQ=3, 4,5,6,7,10,11,12
The serial port IO port address and interrupt address are automatically detected.
Serial Port I/O port address is 3E8h and the interrupt address is IRQ7
Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 3E8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 2E8h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Serial Port I/O port address is 2E0h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Î
IO=2F0h; IRQ=3, 4,5,6,7,10,11,12
Î Device Mode [RS422]
Use the Device Mode option to select the serial port mode.
Î
RS422 DEFAULT
Î
RS485
Serial Port I/O port address is 2F0h and the interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12
Enables serial port RS-422 support. Enables serial port RS-485 support.
Page 62
AFL2-15A-H61

4.3.9 H/W Monitor

The H/W Monitor menu (BIOS Menu 13) shows the operating temperature, fan speeds and system voltages.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Temperature :+58 °C Environment Temperature 1 :+63 °C Environment Temperature 2 :+39 °C SYS Temperature :+38 °C
CPU FAN Speed :648 RPM
Fanless Temp. Overwrite Control [Enabled] Temperature Of FANLess [32 C]
Fanless Temperature Reading :+32 °C
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
BIOS Menu 13: Hardware Health Configuration
Î Hardware Health St atus
The following system parameters and values are shown. The system parameters that are monitored are:
System Temperatures:
o CPU Temperature o Environment Temperature o System Temperature
Fan Speeds:
o CPU Fan Speed
Î Fanless Temp. Overwrite Control [Enabled]
Use the Fanless Temp. Overwrite Control BIOS option to enable or disable Temperature of Fanless configuration.
Page 63
AFL2-15A-H61
Î
Disabled
Î
Enabled DEFAULT
Î Temperature Of Fanless [32 C]
Temperature of Fanless option can not be configured. Temperature of Fanless option can be configured.
NOTE:
If the Temperature of Fanless is enabled, the fan will only turn on when the Environment Temperature 1 reaches to the temperature set in the following Temperature of Fanless option.
For safety reason, the fan will turn on automatically to cool down the system when the CPU temperature exceeds 80 ºC, no matter the Temperature of Fanless is enabled or not.
Use the Temperature Of Fanless option to configure default temperature setting. When the environment temperature is lower than default temperature setting, the fan will turn off. When the environment temperature is higher than default temperature setting, the fan will turn on. A list of available options is shown below:
Î
Disabled
Î
4 C
Î
8 C
Î
12 C
Î
16 C
Î
20 C
Disabled the Temperature Of Fanless function When the environment temperature 1 is lower than 4 C,
the fan will be switched off. When the environment temperature 1 is lower than 8 C,
the fan will be switched off. When the environment temperature 1 is lower than 12
C, the fan will be switched off. When the environment temperature is lower than 16 C,
the fan will be switched off. When the environment temperature 1 is lower than 20
C, the fan will be switched off.
Page 64
AFL2-15A-H61
Î
24 C
Î
28 C
Î
32 C DEFAULT
Î
36 C
Î
40 C
When the environment temperature 1 is lower than 24 C, the fan will be switched off.
When the environment temperature 1 is lower than 28 C, the fan will be switched off.
When the environment temperature 1 is lower than 32 C, the fan will be switched off.
When the environment temperature 1 is lower than 36 C, the fan will be switched off.
When the environment temperature 1 is lower than 40 C, the fan will be switched off.

4.3.10 Serial Port Console Redirection

The Serial Port Console Redirection menu (BIOS Menu 14) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
COM1
Console Redirection [Disabled]
> Console Redirection Settings
COM2
Console Redirection [Disabled]
> Console Redirection Settings
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 14: Serial Port Console Redirection
Î Console Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection fun ction.
Console Redirection Enable or Disable.
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
Page 65
c
s
AFL2-15A-H61
Î
Disabled DEFAULT
Î
Enabled
Disabled the console redirection function Enabled the console redirection function

4.4 iEi Feature

Use the iEi Feature menu (BIOS Menu 15) to configure the auto recovery function.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
iEi Feature
Auto Recovery Function [Disabled]
Micro SD Card [Enabled]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
Auto Recovery Function Reboot and recover system automatically within 10 min, when OS
rashes. Please install Auto Recovery API
ervice before enabling this function
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
BIOS Menu 15: iEi Feature
Î Auto Recovery Function [Disabled]
Use the Auto Recovery Function option to enable or disable auto recovery on the system.
Î
Disabled DEFAULT
Î
Enabled
Page 66
Auto Recovery Function support disabled Auto Recovery Function support enabled
AFL2-15A-H61
Î Micro SD Card [Enabled]
Use the Micro SD Card option to enable or disable the microSD card slot on the front panel.
Î
Disabled DEFAULT
Î
Enabled
microSD card slot is disabled microSD card slot is enabled

4.5 Chipset

Use the Chipset menu (BIOS Menu 16) to access the North Bridge, South Bridge, Integrated Graphics, and ME Subsystem configuration menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> North Bridge > South Bridge > Integrated Graphics > ME Subsystem
North Bridge Parameters
---------------------
ÅÆ
: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit
: Select Screen
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 16: Chipset
Page 67
c

4.5.1 Northbridge Configuration

Use the North Bridge menu (BIOS Menu 17) to configure the Northbridge chipset.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Chipset
Memory Information
Total Memory 2048 MB (DDR3 1333)
Memory Slot0 2048 MB (DDR3 1333) Memory Slot1 0 MB (DDR3 1333)
Initate Graphic Adapter [PEG/IGD] IGD Memory [256M]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
AFL2-15A-H61
Select which graphics
ontroller to use as the primary boot device.
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit
BIOS Menu 17: Northbridge Chipset Configuration
Î Initiate Graphic Adapter [PEG/IGD]
Use the Initiate Graphic Adapter option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD. Configuration options are listed below:
IGD PCI/IGD PCI/PEG PEG/IGD D PEG/PCI
Î IGD Memory [256M]
Use the IGD Memory option to specify the amount of system memory that can be used by
EFAULT
the internal graphics device.
Page 68
S
AFL2-15A-H61
Î
32M
Î
64M
Î
128M
Î
256M DEFAULT
Î
512M
32 MB of memory used by internal graphics device 64 MB of memory used by internal graphics device 128 MB of memory used by internal graphics
device 256 MB of memory used by internal graphics
device 512 MB of memory used by internal graphics
device

4.5.2 Southbridge Configuration

Use the South Bridge menu (BIOS Menu 18) to configure the Southbridge chipset.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Chipset
Auto Power Button Status [ON]
Restore AC Power Loss [Last State] Power Saving Function [Disabled] Init LED Bar To DEFAULT [Enabled] WIFI Function [Enabled] DMIC Function [Enabled] BT Function [Enabled] RFID Function [Enabled] Auto Dimming Support [Disabled]
Audio Configuration
Azalia HD Audio [Enabled] Azalia internal HDMI codec [Enabled]
PCI Express Ports Configuration
PCIe LAN PXE Boot [Disabled] PCIe LAN Controller [Enabled] PCIe USB 3.0 Controller [Enabled]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
pecify what state to go to when power is re-applied after a power failure (G3 state).
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit
BIOS Menu 18: Southbridge Chipset Configuration
Page 69
Î Restore AC Power Loss [Last State]
Use the Restore AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.
AFL2-15A-H61
Î
Power Off
Î
Power On
Î
Last State DEFAULT
Î Power Saving Function [Disabled]
Use the Power Saving Function BIOS option to enable or disable the power saving function.
Î
Disabled DEFAULT
Î
Enabled
Î WIFI Function [Enabled]
Use the WIFI Function option to enable or disable the Wi-Fi function.
The system remains turned off The system turns on The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.
Power saving function is disabled. Power saving function is enabled. It will reduce power
consumption when the system is off.
Î
Disabled
Î
Enabled DEFAULT
Î DMIC Function [Enabled]
Use the DMIC Function option to enable or disable the Microphone function.
Î
Disabled
Î
Enabled DEFAULT
Î BT Function [Enabled]
Use the BT Function option to enable or disable the BT function.
Page 70
Wi-Fi function disabled Wi-Fi function enabled
Microphone function disabled Microphone function enabled
AFL2-15A-H61
Î
Disabled
Î
Enabled DEFAULT
Î RFID Function [Enabled]
Use the RFID Function option to enable or disable the RFID function.
Î
Disabled
Î
Enabled DEFAULT
Î Auto Dimming Support [Disabled]
Use the Auto Dimming Support option to enable or disable the auto dimming function.
Î
Disabled DEFAULT
Î
Enabled
BT function disabled BT function enabled
RFID function disabled RFID function enabled
Auto dimming function disabled Auto dimming function enabled
Î Azalia HD Audio [Enabled]
Use the Azalia HD Audio option to enable or disable the High Definition Audio controller.
Î
Disabled
Î
Enabled DEFAULT
Î Azalia internal HDMI codec [Enabled]
Use the Azalia internal HDMI codec option to enable or disable the internal HDMI codec for High Definition Audio.
Î
Disabled
Î
Enabled DEFAULT
The onboard High Definition Audio controller is disabled The onboard High Definition Audio controller is detected
automatically and enabled
Disable internal HDMI codec for High Definition Audio Enable internal HDMI codec for High Definition Audio
Page 71
Î PCIe LAN PXE Boot [Disabled]
Use the PCIe LAN PXE Boot option to enable or disable the boot option for the PCIe LAN PXE.
AFL2-15A-H61
Î
Disabled DEFAULT
Î
Enabled
Î PCIe LAN Controller [Enabled]
Use the PCIe LAN Controller option to enable or disable the PCI Express LAN controller.
Î
Disabled
Î
Enabled DEFAULT
Î PCIe USB 3.0 Controller [Enabled]
Use the PCIe USB 3.0 Controller BIOS option to enable or disable the PCIe USB 3.0 controller.
Î
Disabled
Î
Enabled DEFAULT
Disables PCIe LAN PXE Boot option Enables PCIe LAN PXE Boot option
The onboard PCIe LAN controller is disabled The onboard PCIe LAN controller is enabled
The onboard PCIe USB 3.0 controller is disabled The onboard PCIe USB 3.0 controller is enabled

4.5.3 Integrated Graphics

Use the Integrated Graphics menu (BIOS Menu 19) to configure the video device connected to the system.
Page 72
m
AFL2-15A-H61
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel IGD SWSCI OpRegion Configuration
DVMT Mode Select [DVMT Mode] DVMT Memory [Maximum]
IGD - Boot Type [AUTO]
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
Select DVMT Mode used by Internal Graphics Device. If Fixed Mode selected, IGD Memory
ight need to be changed to a larger value, for IGD to have sufficient memory.
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit
BIOS Menu 19: Integrated Graphics
Î DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode.
Î
Fixed Mode
Î
DVMT Mode DEFAULT
Î DVMT Memory [Maximum]
Use the DVMT Memory option to specify the maximum amount of memory that can be allocated as graphics memory. Configuration options are listed below.
128 MB
A fixed portion of graphics memory is reserved as graphics memory.
Graphics memory is dynamically allocated according to the system and graphics needs.
256 MB  Maximum D
EFAULT
Page 73
Î IGD - Boot Type [AUTO]
Use the IGD - Boot Type option to select the display device used by the system when it boots. For dual display support, select “Auto.” Configuration options are listed below.
AFL2-15A-H61
AUTO LVDS CRT HDMI
DEFAULT

4.5.4 ME Subsystem

Use the ME Subsystem menu (BIOS Menu 20) to configure the Intel® Management Engine (ME) configuration options.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Chipset
Intel ME Subsystem Configuration
ME Version 7.0.10.1203
MEBx Mode [Normal]
Unconfigure AMT/ME [Enabled]
MEBx Mode Help
---------------------
ÅÆ
: Select Screen
: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 20: ME Subsystem
Î MEBx Mode [Normal]
Use the MEBx Mode option to configure MEBx Mode options.
Î
Normal DEFAULT
Î
Hidden Ctrl + P
Page 74
Enables normal mode Enables hidden Ctrl+P function
AFL2-15A-H61
Î
Enter MEBx Setup
Î Unconfigure AMT/ME [Enabled]
Use the Unconfigure AMT/ME option to perform AMT/ME unconfigure without password operation.
Î
Disabled
Î
Enabled DEFAULT
Enables user to enter MEBx setup
Disable AMT/ME unconfigure Enable AMT/ME unconfigure

4.6 Boot

Use the Boot menu (BIOS Menu 21) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Boot Configuration
Bootup NumLock State [On] Quiet Boot [Enabled] Option ROM Messages [Force BIOS] UEFI Boot [Disabled]
Boot Option Priorities
Boot Option #1 [SATA:Optiarc CDRW…] Boot Option #2 [Generic STORAGE DE…]
Floppy Drive BBS Priorities Hard Drive BBS Priorities
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
Select the keyboard NumLock state
---------------------
ÅÆ
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
: Select Screen
BIOS Menu 21: Boot
Î Bootup NumLock State [On]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up.
Page 75
AFL2-15A-H61
Î
On DEFAULT
Î
Off
Î Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.
Does not enable the keyboard Number Lock automatically. To use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad. The Number Lock LED on the keyboard lights up when the Number Lock is engaged.
Î
Disabled
Î
Enabled DEFAULT
Î Option ROM Messages [Force BIOS]
Use the Option ROM Messages option to set the Option ROM display mode.
Î
Force BIOS
Î
Keep Current
Î Boot Option #1 [SATA: Optiarc CDRW…]
Use Boot Option #1 to enable or disable booting from the detected drive.
Î
SATA: Optiarc
DEFAULT
Normal POST messages displayed OEM Logo displayed instead of POST messages
Sets display mode to force BIOS.
Sets display mode to current.
DEFAULT
Enables booting from the detected storage
Page 76
CDRW…
device.
S
AFL2-15A-H61
Î
Disabled
Î Boot Option #2 [Generic STORAGE DE…]
Use Boot Option #2 to enable or disable booting from the detected drive.
Î
Generic STORAGE DE…
Î
Disabled
Î Hard Drive BBS Priorities
Use Hard Drive BBS Priorities option to set the system boot order.
DEFAULT
Disables boot option.
Enables booting from the detected storage device.
Disables boot option.

4.7 Security

Use the Security menu (BIOS Menu 22) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Password Description
If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password must be 3 to 20 characters long.
Administrator Password User Password
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
Password
---------------------
ÅÆ
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
et Setup Administrator
: Select Screen
BIOS Menu 22: Security
Î Administrator Password
Use the Administrator Password field to set or change an administrator password.
Page 77
Î User Password
Use the User Password field to set or change a user password.

4.8 Save & Exit

Use the Save & Exit menu (BIOS Menu 23) to load default BIOS values, optimal failsafe values and to save configuration changes.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Save Changes and Reset Discard Changes and Reset
Restore Defaults Save as User Defaults Restore User Defaults
Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
Reset the system after saving the changes.
---------------------
ÅÆ
: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit
AFL2-15A-H61
: Select Screen
BIOS Menu 23: Exit
Î Save Changes and Reset
Use the Save Changes and Reset option to save the changes made to the BIOS options and reset the system.
Î Discard Changes and Reset
Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program.
Î Restore Defaults
Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus. F3 key can be used for this operation.
Page 78
AFL2-15A-H61
Î Save as User Defaults
Use the Save as User Defaults option to save the changes done so far as user defaults.
Î Restore User Defaults
Use the Restore User Defaults option to restore the user defaults to all the setup options.
Page 79
AFL2-15A-H61
Chapter
5

5 Software Drivers

Page 80
AFL2-15A-H61

5.1 Available Software Drivers

NOTE:
The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates.
The following drivers can be installed on the system:
Chipset Graphic LAN Audio Touch Screen Wi-Fi USB 3.0 Camera
Installation instructions are given below.

5.2 Starting the Driver Program

To access the driver installation programs, please do the following.
Step 1: Insert the CD-ROM that came with the system into a CD-ROM drive attached to
the system.
Step 2: Click AFL2-15A-H61 Driver.
Step 3: A list of available drivers appears.Step 0:
Page 81
AFL2-15A-H61
Figure 5-1: Drivers

5.3 Chipset Driver Installation

To install the chipset driver, please do the following.
Step 1: Access the driver list. (See Section
Step 2: Click “Chipset.”
Step 3: Locate the setup file and double click on it.
Step 4: The setup files are extracted as shown in
5.2)
Figure 5-2.
Page 82
AFL2-15A-H61
Figure 5-2: Chipset Driver Screen
Step 5: When the setup files are completely extracted the Welcome Screen in
5-3 appears.
Step 6: Click Next to continue.
Figure
Figure 5-3: Chipset Driver Welcome Screen
Step 7: The license agreement in
Figure 5-4 appears.
Page 83
Loading...