Integrated Device Technology Inc IDT7007L55JI, IDT7007L55PFI, IDT7007S15G, IDT7007L15G, IDT7007L15J Datasheet

HIGH-SPEED
32K x 8 DUAL-PORT
STATIC RAM

Features

◆

True Dual-Ported memory cells which allow simultaneous
reads of the same memory location

◆

High-speed access

 Military: 25/35/55ns (max.)
 Industrial: 55ns (max.)
 Commercial: 15/20/25/35/55ns (max.)

◆

Low-power operation

 IDT7007S

Active: 850mW (typ.)
Standby: 5mW (typ.)

 IDT7007L

Active: 850mW (typ.)
Standby: 1mW (typ.)

◆

IDT7007 easily expands data bus width to 16 bits or more

Functional Block Diagram

IDT7007S/L

using the Master/Slave select when cascading more than
one device

◆

M/S = H for BUSY output flag on Master,
M/S = L for BUSY input on Slave

◆

Interrupt Flag

◆

On-chip port arbitration logic

◆

Full on-chip hardware support of semaphore signaling
between ports

◆

Fully asynchronous operation from either port

◆

TTL-compatible, single 5V (±10%) power supply

◆

Available in 68-pin PGA and PLCC and a 80-pin TQFP

◆

Industrial temperature range (40°C to +85°C) is available
for selected speeds

OE

L

CE

L

R/W

L

I/O0L- I/O

NOTES:

1. (MASTER): BUSY is output; (SLAVE): BUSY is input.

2. BUSY and INT outputs are non-tri-stated push-pull.

7L

(1,2) (1,2)

BUSY

L

A

A

SEM

INT

14L

0L

L

(2)

L

Addre ss
Decoder

CE
OE

R/W

L
L
L

15

I/O

Control

MEMORY

ARRAY

ARBITRATION

INTERRUPT

SEMAPHORE

LOGIC

M/S

1

I/O

Control

OE

R

CE

R

R/W

R

I/O0R-I/O

BUSY

Address
Decoder

15

CE

R

OE

R

R/W

R

A
A

SEM
INT

2940 drw 01

14R

0R

7R

R

R

(2)

R

JUNE 1999

DSC 2940/8

IDT7007S/L
High-Speed 32K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges

Description

The IDT7007 is a high-speed 32K x 8 Dual-Port Static RAM. The
IDT7007 is designed to be used as a stand-alone 256K-bit Dual-Port RAM
or as a combination MASTER/SLAVE Dual-Port RAM for 16-bit-or-more
word systems. Using the IDT MASTER/SLAVE Dual-Port RAM approach
in 16-bit or wider memory system applications results in full-speed, error­free operation without the need for additional discrete logic.

This device provides two independent ports with separate control,
address, and I/O pins that permit independent, asynchronous access for
reads or writes to any location in memory. An automatic power down

feature controlled by CE permits the on-chip circuitry of each port to enter
a very LOW standby power mode.

Fabricated using IDTs CMOS high-performance technology, these

devices typically operate on only 850mW of power.

The IDT7007 is packaged in a 68-pin pin PGA, a 68-pin PLCC,
and an 80-pin thin quad flatpack, TQFP. Military grade product is
manufactured in compliance with the latest revision of MIL-PRF-38535
QML, Class B, making it ideally suited to military temperature applications
demanding the highest level of performance and reliability.

Pin Configurations

INDEX

I/O

2L

I/O

3L

I/O

4L

I/O

5L

GND
I/O

6L

I/O

7L

V

CC

GND

I/O

0R

I/O

1R

I/O

2R

V

CC

I/O

3R

I/O

4R

I/O

5R

I/O

6R

(1,2,3)

L

L

L

0

1

O

O

/

/

I

I

98765432168676665
10
11

12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

27 28 29 30 31 32 33 34 35 36 37 38 39

L

L

M

W

C

E

/

/
N

E
S

O

R

L

L

L

E
C

C

3

4

1

1

C

A

A

V

IDT7007J

(4)

J68-1

68-Pin PLCC

Top View

(5)

L

L

2

1

1

1

A

A

L

0

L

L

1

A

64 63 62 61

40 41 42 43

L

9

8

7

A

A

A

60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44

L

6

A

A

5L

A

4L

A

3L

A

2L

A

1L

A

0L

INT

L

BUSY

GND
M/

S

BUSY
INT

R

A

0R

A

1R

A

2R

A

3R

A

4R

L

R

R

R

R

C

7

/

E

W

/

N

O

O

/

I

NOTES:

1. All Vcc pins must be connected to power supply.

2. All GND pins must be connected to ground supply.

3. Package body is approximately .95 in x .95 in x .17 in.

4. This package code is used to reference the package diagram.

5. This text does not indicate orientation of the actual part marking.

R

R

M
E
S

R

R

4

E

1

C

A

R

R

D

2

3

1

1

N

A

A

G

2

R

R

R

R

R

R

9

1

1

A

8

0

1

A

A

A

R

6

A

2940 drw 0 2

5

A

7

A

IDT7007S/L
High-Speed 32K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges

Pin Configurations

INDEX

N/C

2L

I/O

3L

I/O

4L

I/O

5L

I/O

GND

6L

I/O

7L

I/O

CC

V

N/C

GND

0R

I/O

1R

I/O

2R

I/O

CC

V

3R

I/O

4R

I/O

5R

I/O

6R

I/O

N/C

(1,2,3)

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20

L

L

1

0

O

O

/

/

I

I

0

9

8

7

1

2

2

2

(con't.)

L

L

L

M

W

C

E

E

/

/
N

787

3
2

S

O

R

7

5

767

4

5

6

2

2

2

L

E
C

4

7

C

/
N

737

3

4

1

1

A

A

2

1

7

L

L

7007P F

PN80-1

80-Pin TQ FP

Top View

7

8

9

2

0

2

2

3

C
C

V

706

(4)

1
3

(5)

L

L

L

2

1

A

9

2
3

1

1

A

686

3
3

L

0

9

1

A

A

7

6

6

4

5

3

3

L

8

A

656

6
3

L

L

C

C

6

7

/

/

A

A

N

N

4

3

1

6

626

60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42

7
3

41

8

9

0

3

3

4

N/C

5L

A

4L

A

3L

A

2L

A

1L

A

0L

A

L

INT
BUSY

GND
M/S

BUSY

R

INT

0R

A

1R

A

2R

A

3R

A

4R

A
N/C
N/C

L

R

,

R

R

R

R

E
O

W

/
R

R

M
E
S

E
C

C

/

7

N

O

/

I

NOTES:

1. All Vcc pins must be connected to power supply.

2. All GND pins must be connected to ground supply.

3. Package body is approximately 14mm x 14mm x 1.4mm.

4. This package code is used to reference the package diagram.

5. This text does not indicate orientation of the actual part marking.

R

R

R

R

C

/
N

D

3

4

N

1

1

G

A

A

R

R

R

R

R

2

1

0

9

1

1

A

A

8

1

A

A

A

R

7

6

5

A

A

A

C

/
N

2940drw 03

C

/
N

3

IDT7007S/L
High-Speed 32K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges

Pin Configurations

(1,2,3)

(con't.)

11

10

09

08

07

06

05

04

03

02

53

A

55

A

57

A

59

V

61

A

14L

63

SEM

65

OE

67

I/O

68

I/O

51 50 48 46 44 42 40 38 36

S

L

BUSY

M/

INT

R

R

A

0R

7L

52

A

A

5L

49 39 37

A

A

6L

4L

A

2L

A

0L

BUSY

47 45 43 41 34

INT

L

3L

A

1L

GND

54

9L

A

8L

56

11L

A

10L

58

CC

60

A

12L

A

13L

IDT7007G

G68-1

(4)

68-Pin PGA

62

L

CE

L

Top View

64

L

W

R/

L

66

0L

N/C

13579

1L

I/O

2L

I/O

GND GND

4L

I/O

7L

(5)

11 13 15

V

1R

CC

I/O

I/O

A

A

1R

2R

4R

A

3R

35

A

4R

32

A

7R

30

A

9R

28

A

11R

26

GND

24

A

14R

22

SEM

R

20

OE

R

18 1 9
I/O

7R

33

31

29

27

25

23

21

A

A

A

CE

R/

A

5R

A

6R

A

8R

10R

12R

13R

W

N/C

R

R

01

I/O

3L

I/O

5L

I/O

6L

ABCDEFGH J

INDEX

NOTES:

1. All Vcc pins must be connected to power supply

2. All GND pins must be connected to power supply

3. Package body is approximately 1.8 in x 1.8 in x .16 in.

4. This package code is used to reference the package diagram.

5. This text does not indicate orientation of the actual part marking.

246810121416

17

I/O

V

CC

I/O2RI/O3RI/O

0R

5R

I/O

6R

K

L

2940 drw 04

Pin Names

Left Port Right Port Names

CE

L CER

W

L

R/

L OER

OE

14L

A0L - A

I/O0L - I/O

SEM

INT

BUSY

7L

L SEMR

L INTR

L BUSYR

W

R

R/

14R

A0R - A

I/O0R - I/O

S

M/

CC

V

GND Ground

7R

Chip Enables

Read/Write Enable

Output Enable

Address

Data Input/ Output

Semaphore Enable

Inte rrup t Flag

Busy Flag

Master or Slave Select

Power

2940 tbl 01

4

IDT7007S/L
High-Speed 32K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges

Truth Table I: Non-Contention Read/Write Control

(1)

Inputs

R/

CE

W

OE SEM

H X X H Hig h-Z Desel ected: Po wer-Down

LLXHDATA

LHLHDATAOUT Read Memory

X X H X High-Z Outputs Disabled

NOTE:

0L  A14L ≠ A0R  A14R

1. A

Outputs

I/O0-7

IN Write to Memory

Mode

2940 tbl 02

Truth Table II: Semaphore Read/Write Control

Inputs Outputs

CE

R/W

OE SEM

HHL LDATA

H

↑

XLDATAINWrite I/O0 into Semaphore Flag

LXXL

NOTE:

1. There are eight semaphore flags written to via I/O

Absolute Maximum Ratings

Symbol Rating Commercial

(2)

TE RM

V

Te rminal Vo ltage
with Respect
to GND

T

BIAS

Temperature

Under Bias

STG

T

Storage

Temperature

OUT

I

DC Output
Current

NOTES:

1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those
indicated in the operational sec-tions of this specification is not implied. Exposure
to absolute maxi-mum rating conditions for extended periods may affect
reliability.

TERM must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns

2. V
maximum, and is limited to

& Industrial

-0.5 to +7.0 -0.5 to +7.0 V

-55 to + 125 -55 to +135oC

-55 to + 120 -65 to +150oC

50 50 mA

< 20mA for the period of VTERM > Vcc + 10%.

Capacitance (TA = +25°C, f = 1.0mhz)

Symbol Parameter

IN

C

Input Capacitance VIN = 3dV 9 pF

OUT

C

Outp ut Cap acitance V

NOTES:

1. This parameter is determined by device characterization but is not production
tested. TQFP package only.

2. 3dV represents the interpolated capacitance when the input and output signals
switch from 0V to 3V or from 3V to 0V.

(1)

Conditions

OUT

= 3dV 10 pF

0-7

I/O

OUT

Read Semaphore Flag Data Out (I/O0-I/O7)

______

0 and read from all I/O's. These eight semaphores are addressed by A0 - A2.

Military Unit

(1)

Not Allowed

Maximum Operating Temperature
and Supply Voltage

Grade

Military -55

Commercial 0OC to + 70OC0V 5.0V + 10%

Industrial -40

NOTES:

1. This is the parameter T

2. Industrial temperature: for other speeds, packages and powers contact your

2940 tbl 04

sales office.

Recommended Operating
Conditions

Symbol Parameter Min. Typ. Max. Unit

CC

V

Supply Voltag e 4.5 5.0 5.5 V

GND Ground 0 0 0 V

IH

Inp ut Hig h Voltage 2.2

V

(2)

Max. Unit

2940 tbl 07

IL

V

Inp ut Low Voltage -0.5

NOTES:

IL > -1.5V for pulse width less than 10ns.

1. V

TERM must not exceed Vcc + 10%.

2. V

5

(1)

Mode

(1,2)

Ambient

Temperature GND Vcc

O

C to+125OC0V 5.0V + 10%

O

C to + 85OC0V 5.0V + 10%

A.

(1)

____

____

2940 tbl 03

2940 tbl 05

(2)

6.0

0.8 V

2940 tbl 06

V

IDT7007S/L
High-Speed 32K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges

DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range

(VCC = 5.0V ± 10%)

7007S 7007L

Symbol Parameter Test Conditions

|ILI| Input Leakage Current

| Output Leakage Current

|I

LO

OL

V

V

NOTE:

1. At Vcc

Output Low Voltage IOL = 4mA

Output High Voltage IOH = -4mA 2.4

OH

< 2.0V, input leakages are undefined.

(1)

VCC = 5.5V, VIN = 0V to V

CE = V

IH

, V

= 0V to V

OUT

CC

CC

___

___

___

DC Electrical Characteristics Over the Operating

(1,6)

Temperature and Supply Voltage Range

Symbol Parameter Test Condition Versi on

CC

I

Dynamic Ope rating
Current
(Both Ports Active )

SB1

Standb y Current

I

(Both Ports - TTL Level
Inputs)

SB2

Standb y Current

I

(One Port - TTL Leve l
Inputs)

SB3

Full Standb y Current

I

(Both Ports - All CMOS
Level Inputs)

IL

, Outputs Open

= V

CE

IH

SEM = V

(3)

MAX

f = f

L

R

=

CE
SEMR = SEML = V

MAX

f = f

"A"

CE

Active Port Outputs Open,

MAX

f=f

SEMR = SEML = V

Both Ports

R

> VCC - 0.2V

CE

IN

> VCC - 0.2V o r

V
VIN <

IH

= V

CE

(3)

= VIL and CE

(3)

L

and

CE

0.2V, f = 0

(4)

IH

IH

"B"

= V

(5)

IH

SEMR = SEML > VCC - 0.2V

SB4

Full Standb y Current

I

(One Port - All CMOS
Level Inputs)

"A"

< 0.2V and

CE
CE

"B"

> VCC - 0.2V

(5)

SEMR = SEML > VCC - 0.2V

IN

> VCC - 0.2V or VIN < 0.2V

V
Active Port Outputs Open

(3)

MAX

f = f

NOTES:

1. 'X' in part numbers indicates power rating (S or L)

CC = 5V, TA = +25°C, and are not production tested. ICCDC = 120mA (Typ.)

2. V

3. At f = f

MAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, and using AC Test Conditions of input

levels of GND to 3V.

4. f = 0 means no address or control lines change.

5. Port "A" may be either left or right port. Port "B" is the opposite from port "A".

6. Industrial temperature: for other speeds, packages and powers contact your sales office.

COM' L SL190

MIL &
IND

COM' L S

MIL &
IND

COM' L

MIL &
IND

COM' L

MIL &
IND

COM' L

MIL &
IND

(VCC = 5.0V ± 10%)

7007X15

Com'l Only

(2)

190

___

S

___

L

L3535

___

S

___

L

SL125

125

___

S

___

L

SL1.0

0.2

___

S

___

L

SL120

120

___

S

___

L

10

10

0.4

___

Max. Typ.

325
285

220
190

190
160

180
180

___

___

85
60

___

___

115
115

___

___

15

5

0.2

___

___

110
110

___

___

7007X20

Com'l Only

(2)

___

___

30
30

___

___

___

___

1.0

___

___

___

___

___

___

___

2.4

Max. Typ.

315
275

___

___

85
60

___

___

210
180

___

___

15

5

___

___

185
160

___

___

5µA

5µA

0.4 V

___

7007X25
Com'l &

Military

(2)

Max.

170

305

170

265

170

345

170

305

25
25

25
25

105
105

105
105

1.0

0.2

1.0

02.

100
100

100
100

8560mA

100

80

200

170

230
200

15

5

30
10

175
160

200

175

UnitMin. Max. Min. Max.

V

2940 tbl 08

UnitTyp.

mA

mA

mA

mA

2940 tbl 09

6

IDT7007S/L
High-Speed 32K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges

DC Electrical Characteristics Over the Operating

(1,6)

Temperature and Supply Voltage Range

Symbol Parameter Test Condition Version

I

I

SB1

I

SB2

I

SB3

CC

Dynamic Operating Current
(Both Ports Active)

Standby Current
(Bo th P orts - TTL Leve l
Inp uts)

Standby Current
(One Port - TTL Level Inputs)

Full Standby Current (Both
Ports - All CMOS Level
Inp uts)

CE = V

, Outputs Open

IL

SEM = V

IH

(3)

f = f

MAX

CE

= CER = V

L

SEMR = SEML = V

f = f

MAX

CE

= VIL and CE

"A"

Active Port Outputs Open,
f=f

MAX

SEMR = SEML = V

IH

(3)

(3)

IH

= V

"B"

IH

Both Ports CEL and

CE

> VCC - 0.2V

R

> VCC - 0.2V or

V

IN

VIN <

0.2 V, f = 0

(4)

SEMR = SEML > VCC - 0.2V

(5)

IH

(con't.) (VCC = 5.0V ± 10%)

COM' L SL160

MIL &
IND

COM' L S

MIL &
IND

COM' L S

MIL &
IND

COM' L SL1.0

MIL &
IND

7007X35
Com'l &

Military

(2)

Max. Typ.

295

160

____

S

____

L

20

L

20

____

S

____

L

95

L

95

____

S

____

L

255

335
295

85
60

100

80

185
155

215
185

15

0.2

____

S

____

L

5

30
10

7007X55

Com'l, Ind

& Military

(2)

150
150

150
150

20
20

13
13

85
85

85
85

1.0

0.2

1.0

0.2

Max.

270
230

310
270

85
60

100

80

165
135

195
165

15

5

30
10

UnitTyp.

mA

mA

mA

mA

I

SB4

NOTES:

1. 'X' in part numbers indicates power rating (S or L)

CC = 5V, TA = +25°C, and are not production tested. ICCDC = 120mA (Typ.)

2. V

3. At f = f

AC Test Conditions of input levels of GND to 3V.

4. f = 0 means no address or control lines change.

5. Port "A" may be either left or right port. Port "B" is the opposite from port "A".

6. Industrial temperature: for other speeds, packages and powers contact your sales office.

Full Standby Current
(One Port - All CMOS Level
Inp uts)

MAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, and using

CE

< 0.2V and

"A"

CE

> VCC - 0.2V

"B"

(5)

SEMR = SEML > VCC - 0.2V

> VCC - 0.2V or VIN < 0.2V

V

IN

Active Port Outputs Open

(3)

f = f

MAX

COM' L S

MIL &
IND

90

L

90

____

S

____

L

160
135

190
165

80

135

80

110

80

165

80

140

mA

2940 t bl 1 0

7