IDP SMART 31 User Manual

User Manual

SMART Series

SMART-31S, SMART-31D

Users must respect the copyright laws applicable in their country. This manual must not be photocopied, translated, reproduced or transmitted in whole or in part for any reason and by the means that might be, albeit electronic or mechanical, without the express, written authorization of the company IDP card printer.

All information contained herein may be subject to modification without prior notice. IDP card printer accepts no liability for any possible errors herein, nor for any accidental

damage or damage caused through the dissemination or the use of this manual.

Trademarks

SMART-31 is a trademark and IDP is a registered trademark of IDP card printer. Windows is registered trademarks of Microsoft Corp. All other trademarks or registered trademarks are marks of their respective holders. SMART-31 Design is a trademark of IDP.

Return Materials Authorization

In order to make a warranty claim you must contact an IDP Reseller. You will be responsible for packaging the printer for shipment and the costs of shipping and insurance of the printer from the point of use of the printer to the IDP Reseller. The IDP Reseller will bear the costs of shipping and insuring the printer from the repair location to the address from which the printer was shipped.

Before returning any equipment for in-warranty or out of warranty repair, contact an IDP Reseller or an IDP Service Center for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside of the box. For more information about RMA or IDP warranty statements, refer to the Warranty booklet on the quick install guide.

Table of Contents

1. Introduction ................................................................................. 9

1.1 Printer outside features ................................................................................................................................. 9

1.2 Printer inside features ....................................................................................................................................... 11

1.3 Ribbon cartridge features ........................................................................................................................... 12

1.4 Display and Buttons ...................................................................................................................................... 13

2. Printer installation ..................................................................... 14

2.1. Connecting a power and a USB cable .................................................................................................. 14

2.2. Fitting the ribbon ............................................................................................................................................. 15

2.3. Loading the cards .......................................................................................................................................... 18

2.4. The withdrawal of printed cards. .............................................................................................................. 20

2.5. Driver installation (Windows 7 / 8 / 10) .................................................................................................. 21

3. Driver configuration ................................................................... 25

3.1. Printer Properties ............................................................................................................................................... 25

3.2. Advanced Options ............................................................................................................................................. 29

3.3. Other settings ...................................................................................................................................................... 32

4. Utilities ...................................................................................... 35

4.1. Card Printer Config ........................................................................................................................................... 35

4.2. Network configuration ...................................................................................................................................... 44

4.3. Card Printer Test ............................................................................................................................................... 53

4.4. Firmware update ................................................................................................................................................ 60

5. Optional device driver installation ............................................. 62

5.1. Contact smartcard reader .............................................................................................................................. 62

5.2. Contactless smartcard reader ...................................................................................................................... 65

6. Troubleshooting ........................................................................ 68

6.1. Error Message .................................................................................................................................................... 68

6.2. Cleaning the printer .......................................................................................................................................... 72

6.3 TPH (Thermal Print Head) replacement .................................................................................................... 76

6.4. Card movement .................................................................................................................................................. 78

6.5. Printing quality .................................................................................................................................................... 79

6.6. Magnetic stripe encoding ............................................................................................................................... 81

6.7. General operation .............................................................................................................................................. 81

7. Specification ............................................................................. 83

Table of Figures

Figure 1 SMART-31 front features

Figure 2 SMART-31 rear features

Figure 3 SMART-31S (Standard)

Figure 4 SMART-31D (Dual)

Figure 6 SMART-31 Inside features

Figure 7 Ribbon cartridge features

Figure 8 SMART-31S Connection of power and USB cable

Figure 9 SMART-31D Connection of power and USB cable

Figure 10 Top Cover open

Figure 11 Take out the ribbon cartridge

Figure 12 Loading the ribbon 1

Figure 13 Loading the ribbon 2

..........................................................................................................................................................15

............................................................................................................................................. 9

.............................................................................................................................................. 9

.............................................................................................................................................10

......................................................................................................................................................10

.......................................................................................................................................11

..........................................................................................................................................12

................................................................................................................................15

.................................................................................................................................................16

........................................................................................14

Figure 14 Installing the cleaning roller

Figure 15 Peeling the protective wrap per

Figure 16 Installing the ribbon cartridge

Figure 17 Close Top Cover

Figure 18 Adjusting the card thickness Device

Figure 19 Preparing the card 1

Figure 20 Preparing the card 2

Figure 21 Loading the cards 1

Figure 22 Loading the cards 2

Figure 23 Loading the cards 3

Figure 24 Loading the cards 4

Figure 25 SMART-31 Withdrawal a card

.........................................................................................................................................................17

...................................................................................................................................................19

...................................................................................................................................16

.............................................................................................................................16

................................................................................................................................17

.................................................................................................................................................18

..............................................................................................................................20

..................................................................................................................18

Figure 26 SMART-31 Dividing a stacker

Figure 27 Install Win7 driver 1

Figure 28 Install Win7 driver 2

Figure 29 nstall Win7 driver 3

...................................................................................................................................................21

....................................................................................................................................................21

...............................................................................................................................20

Figure 30 Install Win7 driver 6

...................................................................................................................................................22

Figure 31 Install Win7 driver 8

Figure 32 Install Win7 driver 9

Figure 33 Install Win7 driver 10

Figure 34 Install Win7 driver 11

Figure 35 Install Win7 driver 12

Figure 36 Install Win7 driver 13

Figure 37 Install Win7 driver 14

Figure 38 Install Win7 driver 15

Figure 39 Printer properties

Figure 40 Layout

Figure 41 Input / Output

Figure 42 Printing

..............................................................................................................................................................................25

............................................................................................................................................................................26

........................................................................................................................................................25

...............................................................................................................................................................26

...................................................................................................................................................22

................................................................................................................................................23

................................................................................................................................................24

Figure 43 Encoding

Figure 44 Magnetic Encoding Advanced Option

Figure 45 Printer sharing

Figure 46 Ports

Figure 47 Advanced

Figure 48 Color Management

Figure 49 Security

Figure 50 Service

Figure 51

Figure 52

Figure 53

Figure 54

CardPrinterConfig Log-in

CardPrinterConfig start

CardPrinterConfig – Card Printer Basic Setup

SMART-31 R density

........................................................................................................................................................................27

.............................................................................................................................................................32

.................................................................................................................................................................................32

.......................................................................................................................................................................33

....................................................................................................................................................33

...........................................................................................................................................................................34

............................................................................................................................................................................34

........................................................................................................................................35

...........................................................................................................................................35

...............................................................................................................................................38

...............................................................................................................28

..............................................................................................36

Figure 55

Figure 56

Figure 57

Figure 58

Color density

Resin Black density

Overlay density

CardPrinterConfig – Card Printer Advanced Setup

................................................................................................................................................................38

..................................................................................................................................................39

...........................................................................................................................................................39

....................................................................................40

Figure 59

CardPrinterConfig – Flipper Setup

.....................................................................................................................43

Figure 60

Figure 61

Figure 62

Figure 63

Figure 64

Figure 65

Figure 66

Figure 67

Figure 68

Figure 69

Figure 70

Figure 71

Rear view of SMART-31 printer 1

Rear view of SMART-31 printer 2

Running the NetAdmin

Network printer is not found

Connecting to USB port

NetAdmin Log-in

USB port state

Rebooting the network module

Reset to default

Upgrading the firmware 1

Upgrading the firmware 2

Upgrading the firmware 3

.............................................................................................................................................................47

............................................................................................................................................45

..................................................................................................................................45

..........................................................................................................................................46

........................................................................................................................................................46

............................................................................................................................47

..........................................................................................................................................................48

.......................................................................................................................................48

.......................................................................................................................................49

.......................................................................................................................44

Figure 72

Figure 73

Figure 74

Figure 75

Figure 76

Figure 77

Figure 78

Figure 79

Figure 80

Figure 81

Figure 82

Figure 83

Dynamic IP configuration

Static IP configuration

Network service configuration

OCP configuration

Network user configuration

CardPrinterTest

Magnetic stripe encoding

Contact smartcard encoding

Contactless smartcard encoding

Run CardPrinterFirmware

Select Firmware

Update Firmware

..........................................................................................................................................................53

.........................................................................................................................................................60

.......................................................................................................................................................61

.......................................................................................................................................50

..............................................................................................................................................50

..............................................................................................................................51

.....................................................................................................................................................51

....................................................................................................................................52

.......................................................................................................................................56

.................................................................................................................................58

......................................................................................................................................60

.........................................................................................................................59

Figure 84

Figure 85

Figure 86

Figure 87

Contact smartcard reader driver installation

License agreement

Installing the contact smartcard reader driver

Completing the smartcard reader driver installation

...................................................................................................................................................63

..................................................................................................62

...............................................................................................63

...................................................................................64

Figure 88

Found New Hardware Wizard

..............................................................................................................................65

Figure 89

Figure 90

Figure 91

Figure 92

Figure 93

Figure 94

Figure 95

Figure 96

Figure 97

Figure 98

Figure 99

Figure 100

Installation method selection

Driver locat io n

Completing the driver installation

Exclusive long cleaning card for SMART-31 printer

Printer cleaning start

Printer cleaning Step 1

Printer cleaning Step 2

Printer cleaning Step 3

Printer cleaning Step 4

Printer cleaning Step 5

Printer cleaning Step 6

Thermal Print Head

.............................................................................................................................................................66

................................................................................................................................................72

................................................................................................................................66

........................................................................................................................67

............................................................................................................................................73

............................................................................................................................................74

............................................................................................................................................75

.............................................................................................................................................76

...................................................................................72

Figure 101

Figure 102

Figure 103

Figure 104

Figure 105

Figure 106

Figure 107

Figure 108

Print head setup

Print head replacement

Print head angle

Printing quality trouble 1

Printing quality trouble 2

Printing quality trouble 3

Printing quality trouble 4

Printing quality trouble 5

.......................................................................................................................................................76

.......................................................................................................................................................77

........................................................................................................................................77

.......................................................................................................................................79

.......................................................................................................................................80

.......................................................................................................................................81

1. Introduction

⑥ Power switch

⑦

⑧

⑨

① Top cover open button

②

③

④

⑤

1.1 Printer outside features

For the user’s convenience, SMART-31 status can be seen through LED and the printer can be controlled by LED button. It takes a power via the 24V adaptor provided with the printer. Using USB and Network port, it is communicated with the user’s PC

The following shows the outside functional features found on the printer.

①

③

②

Fan Input hopper LED buttons Output hopper

④

⑤

Figure 1 SMART-31 front features

24V power connector Network port

In case there is no network option, it is closed.

USB port

There are three models in SMART-31 card printer series such as SMART-31 S, SMART-31D

⑦

⑥

⑧ ⑨

Figure 2 SMART-31 rear features

SMART-31S (Figure.3) is the standard card printer. It can be printed in single side with the encoding. This manual is prepared based on SMART-31S.

SMART-31D (Figure.4) has a flipper which can enable to print in both sides. SMART-31D can print the both side of the card with the encoding.

Figure 3 SMART-31S (Standard)

Figure 4 SMART-31D (Dual)

1.2 Printer inside features

In SMART printer, the ribbon is installed by a ribbon cartridge which can be used semi permanently. The following shows the inside functional features found on your SMART-31 printer.

②

④

③

①

Figure 5 SMART-31 Inside features

① Output hopper(Stacker)

Collect the printed card and/or encoded cards. Maximum 25 cards are loaded and the extra printed/encoded card is passed out. It can be withdrawed when pulling forward.

② Input hopper

Load the cards for printing. Maximum 40 cards are loaded when cover is closed; Maximum 80 cards are loaded when the cover is opened.

③ Ribbon cartridge Install the ribbon and the disposable cleaning roller.

④ Thermal Print Head

This enables the cards to be printed.

(Caution!: This is very hot after printing. Do not contact the surface of the Thermal Print Head with fingers or a sharp metal object to avoid degrading print quality or damaging printer head permanently.)

1.3 Ribbon cartridge features

①

②

③

④

SMART-31 printer uses the same ribbon cartridge as a SMART-30’s.

(However, the ribbon for SMART-31 is incompatible with SMART-30’s. The color of gear part of the ribbon for SMART-31 is gray.)

② ③

Ribbon cartridge

④

Take up parts

①

① Ribbon cartridge

-. Install a ribbon and a disposable cleaning roller provided with the ribbon.

-. In the case of SMART-31 R model, a ribbon is not used, and a disposable cleaning roller is only installed and used.

-. This semi-permanent ribbon cartridge is a component of the printer. Printer does not operate if it is broken or damaged. In this case, please contact printer reseller.

② ③ Take up & Supply parts

-. Ribbon is wrapped to the supply parts as the Picture. It should be installed as the

Figure.7

Figure 6 Ribbon cartridge features

Supply parts

Disposable cleaning roller

④ Disposable cleaning roller

-. It removes dust on the surface of card to improve print quality before the card is printed. It should be changed together with the ribbon.

-. After installing the disposable cleaning roller to the ribbon cartridge, peel off the

protective film.

-. It is provided with the ribbon.

-. In the case of SMART-31 R model, you have to purchase the disposable

cleaning roller from the reseller.

1.4 Display and Buttons

The st atus of SMART-31 is displayed on the Watchman program of the Windows tray. The simple status of SMART-31 is displayed by color of LED. It is red when boot up. It is changed to ‘System Ready’ if the printer is fine. It is change to ‘Printing’ when the printer

is working. In case of sensing an error, it is changed to ‘Error’ status. Whenever the top cover is opened, the operation is stopped and the status is ‘Top Cover Open’.

2. Printer installation

2.1. Connecting a power and a USB cable

(1) SMART-31S

Connect the power and USB cable as the below picture. Please refer to the ‘Network Configuration’ if you use the LAN connection.

(2) SMART-31D

Connect the power and USB cable after turning the printer on its side as the below picture. Please refer to the ‘Network Configuration’ if you use the LAN connection.

Figure 7 SMART-31S Connection of power and USB cable

Figure 8 SMART-31D Connection of power and USB cable

2.2. Fitting the ribbon

(2) Open the printer top cover by

(3) Take out the ribbon cartridge.

Before printing, prepare the related items such as a card, a ribbon and a cleaning roller. In this section we invite you to know the proper method of installing the ribbon and t he cleaning roller into the printer.

(1) Turn off the printer

pressing the top cover open button.

Figure 9 Top Cover open

Figure 10 Take out the ribbon cartridge

(4) Install a ribbon into the ribbon

cartridge as the right pictu re.

(5) Insert the supply side of the (6) Install the disposable cleaning roller

(7) Peel the protective wrapper from the

Figure 11 Loading the ribbon 1

ribbon to no.1 hole and press the opposite (no.2). Insert the take-up side of the ribbon same method to no.3 and no.4. After inserting, tighten the ribbon.

(Caution! If the ribbon is not tightened, a rolling up error might be happened.)

to the ribbon cartridge.

①

②

Figure 12 Loading the ribbon 2

Figure 13 Installing the cleaning roller

③

④

cleaning roller.

After removing the protective wrapper, the cleaning roller should be kept clean from fingerprints, dust and foreign substances to avoid contamination because it is adhesive.

(Caution! Do not use without peeling off the protective wrapper because the cleaning roller cannot perform its function.)

Figure 14 Peeling the protective wrapper

(8) Install the ribbon cartridge into the printer after installing the ribbon with a cleaning roller

to the cartridge.

(9) Close the top cover

(If it is not closed properly, check the installation state of the ribbon cartridge.)

Figure 15 Installing the ribbon cartridge

Figure 16 Close Top Cover

2.3. Loading the cards

(1) Open the input hopper cover.

(2) To separate cards from each

This section shows how to load the plastic cards.

Release two screws, insert a card to use and fix screws after adjust the card thickness device. 0.4mm and

0.8 mm cards are supported.

(Caution! If the adjustment is not correct, it will make some error. Use the type of cards in the specification of this manual. Always keep the card surface clean state.)

other, push a stack of cards back and forth to an angle about 45 degrees vertically.

(Static charge makes cards stuck with significant adhesive force. These cards must be physically separated from each other before inserted into the feeder. If not separated, feeding or printing problems may occur.)

Figure 17 Adjusting the card thickness Device

Figure 18 Preparing the card 1

Figure 19 Preparing the card 2

(3) Stand the stack of cards

vertically after separating

(4) Load the cards on the input

(5) When insert each one card,

hopper properly and close the hopper cover.

Figure 20 Loading the cards 1

insert the card to the end as left picture

(Caution! If the printer has a lock device, a card can’t be inserted one by one.)

Figure 21 Loading the cards 2

Figure 22 Loading the cards 3

Figure 23 Loading the cards 4

2.4. The withdrawal of printed cards.

so you can withdraw the printed cards

Printed cards are passed out to the stacker of front bottom side of SMART-31 printer.

Figure 24 SMART-31 Withdrawal a card

SMART-31’s stacker can be divided as following image. easily.

Figure 25 SMART-31 Dividing a stacker

2.5. Driver installation (Windows 7 / 8 / 10)

(1) Please insert the installation CD.

(2) When “User Account Control”

(3) STEP 1:

Please choose languag e and cli c k “Driver Install”.

Figure 26 Install Win7 driver 1

window is opened, click “Yes”

Please turn off printer if it is connected to PC. Please click “Next”. When you click “Next”, older driver will be removed automatically.

This process will take several minutes to rem ove older driver.

You can select the languages by selecting the combo box as shown on the left picture.

Figure 27 Install Win7 driver 2

Figure 28 nstall Win7 driver 3

(4) STEP 2:

When you click “Next”, the driver

(5) STEP 3: USB

(6) Please turn on the printer

installation will be ready.

Please click “Next” if printe r is connected to USB only.

If you want to install the driver for a printer connected to net work, please select the “TCP/IP Network port” and select the proper printer as step (7).

Figure 29 Install Win7 driver 6

(Network cable is not supplied. Please ask network administrator for more questions.)

Figure 30 Install Win7 driver 8

Figure 31 Install Win7 driver 9

(7) STEP 3: Network

Please select the printer that you want

(8) When driver installation is (9) Please open “Devices and

(10) Please click the right mouse button after cursor is placed on “IDP

to install in the list and click “OK”.

(If no printer comes out on the window, please check the connection.)

completed, please click “Close”

Printers” from “Hardware and Sound”. Please check if “IDP SMART-31 Card Printer” is created.

Figure 32 Install Win7 driver 10

Figure 33 Install Win7 driver 11

SMART-31 Card Printer” icon. Click “Printer properties”.

Figure 34 Install Win7 driver 12

Figure 35 Install Win7 driver 13

(11) Please select “general” tab and

click “Print test page” in “IDP

(12) Please check test card if it is

SMART-31 Card Printer Properties” window.

printed properly and click “Close” if a card is printed properly.

(If card is not printed or error comes out, please refer to “Trouble Shooting”.)

Figure 36 Install Win7 driver 14

Figure 37 Install Win7 driver 15

3. Driver configuration

(1) Printing Preferences (2) Layout

3.1. Printer P roperties

To check printer properties, you need to open printer driver. Please open “Devices and Printers” and right-click “IDP SMART-31 Card Printer”.

Click “Printer Properties”.

Please click “Preferences…” shown on the bottom of the left picture.

- You can select either horizontal or vertical printing direction. To apply your selection, click “OK”.

Figure 38 Printer properties

Figure 39 Layout

(3) Input / Output

[ Supply Tray ]

(4) Printing

both sides printing (It is possible only when

: You can select color or mono print.

to print by using a predefined mask or user

ribbon. You don’t need to select this option

Partial : Partial print mode. It is printed

You can define a mask.

Supply : You can select “Auto” if SMART31 has 1 input hopper. Please select the hopper if it has a multi hopper.

Tray : You can select “CR-80” because SMART-31 supports CR80 cards only.

Do Printing : You can select printing or not

Figure 40 Input / Output

[ Print Side ] Side : Please select one side printing or

you have a flipper.)

[ Front / Back ] Color Flip : You can flip an image Media / Mask : You can indicate the area

defined mask (white card, smartcard, Magnetic stripe card, etc.) on front or back side.

[ Printing ] Ribbon : It shows the type of installed

Figure 41 Printing

User defined mask uses BITMAP file (1012 X 636 pixels).

Blue (RGB(0,0,255)): Print and Overlay

as SMART-31 recognizes ribbon automatically with RF Tag.

Speed : Set printing speed and quality Mode : Set printing mode Standard : Default print mode. Prints all

area of printing

Sky Blue (RGB(0,255,255)): Overlay only

Pink (RGB(255,0,255)): Print only Yellow (RGB(255,255,0)): Florescent

partially for the print area only. Printing

speed can be faster than standard mode.

ribbon(YMCKO, HYMCKO, BYMCKO). It is

(6) Encoding

You can select encoding or

Dither : There are 3 possible selections, Threshold, Random, and Diffusion Dither. It is performed with K and KO ribbon only. (Please select “Diffusion Dither” for high quality.)

Ribbon Save : K ribbon Split : You can set the both

sides (Front:YMCO, Back:K) to save color

only activated while printing both sides option is set.

This tap will be shown only when Magnetic encoder is installed.

Do Encoding : not

Coercivity : You can select the coercivity

to encode

Loco : 300, 600 Oe. HiCo : 2760 Oe. SpCo : 4000 Oe. Auto : Defined automatically

Repeat Count : You can select the retry

count to encoding when encoding is failed

Figure 42 Encoding

(7) Encoding Advanced Opti on

Card Stripe Side : The location of

Do flipping after encoding [No /

magnetic stripe [Bottom / Top] Before Flip : Do flipping before encoding

[No / Yes]

After Flip :

Yes]

 Track Advanced Options : Format : Encoding format (IATA, ABA,

MINS, JISII, Bits Mode)

Track 1 : (defaul t) IATA Track 2 : (defaul t) ABA Track 3 : (defaul t) MINS JIS II Track : (default) JIS II Density: MS encoding density (210, 75) Text Encoding Sentinels : Start, End

Marker for text magnetic encoding

Start : Start Marker End : End Marker

Figure 43 Magnetic Encoding Advanced Option

3.2. Advanced Options

To change the detailed configuration, In the ‘Layout’ tab shown, Please click

“Advanced…” shown on the bottom of the ‘Layout’ tab of the ‘Preferences’

 Reset Default Values: Reset to default.

 Color Correction: You can correc t gamma for colors. You need to use

CardPrinterConfig to adjust color densities.

- Main [-100:100] : Correct gamma for all panels

- Yellow [-100:100] : Correct gamma for yellow panel

- Magenta [-100:100] : Correct gamma for magenta panel

- Cyan [-100:100] : Correct gamma for cyan panel

- Black [-100:100] : Correct gamma for black panel

- Overlay [-100:100] : Correct gamma for overlay panel

 Position Processing: Set criteria for resin black processing.

- Color [-32:32]: to set the position of color panels

- Mono [-32:32]: to set the position of resin or mono panel

- Overlay [-32:32]: to set the position of overlay panel

 Resin Bl ack(K) Processing: Set criteria for resin black processing.

- Text [0:100]: to set density criteria for extracting black objects

- Dot [0:100]: to set density criteria for extracting black dots

- Threshold [0:100]: to set density criteria on dithering

- Dithering Degree [0:100]: to set sharpness on dithering

- Resin Extraction: You can set the method to extract resin black when you use design programs. (If you use the SmartID, you don’t need to select this option.) It will be set automatically.

 Black Object: to extract resin black automatically for text, line, box,

circle, binary images, etc.

 Black Text: to extract resin black for text only  Black Dots: to extract resin black for all of black  Black Dots only: to extract resin black for all of black and not to print on

color panels

 Not Use: not to extract resin black

 Extra Control s : Other options

- Fast Alignment [On/Off]: to set the position of input card to the magnetic encoder or normal printing. If it is on, the printer can save the time to encode

- Rewritable Erase Density [0:100] : to set Erase Density on Rewritable printer

 Wait Option:

- Wait at Internal Module Contactless Encoding Position [On/Off]: to set whether to wait at the Internal RF encoder or not

 Card Side [Front/Back]: to set the direction of card when waiting  Wait Position [-100:100]: to set the position of card to wait from the

 Wait Time [0:1000]: to set time to wait. Unit is second

- Wait at External Module Contactless Encoding Position [On/Off]: to set whether to wait at the External RF encoder or not

 Card Side [Front/Back]: to set the direction of card when waiting  Wait Position [-100:100]: to set the position of card to wait from the

criteria position. Unit is 0.1mm

 Wait Time [0:1000]: to set time to wait. Unit is second

- Wait at Internal Module Contact Encoding Position [On/Off]: to set whether to wait at the Internal IC encoder or not

 Card Side [Front/Back]: to set the direction of card when waiting

 Wait Position [-100:100]: to set the position of card to wait from the

criteria position. Unit is 0.1mm

 Wait Time [0:1000]: to set time to wait. Unit is second

3.3. Other settings

(1) Sharing

(2) Ports

You can share a printer with Sharing tab via Network.

Default is unchecked “Share this printer”.

Figure 44 Printer sharing

Port tab shows which port is connected with SMART-31. SMART-31 has connection with USB Virtual printer port as left picture because SMART-31 uses USB connected to PC.

(Caution! This port is selected automatically. It is recommended to maintain default.)

Figure 45 Ports

(3) Advanced

It is available for Working Time setting,

(4) Color Management (5) Security

You can set the permission to use a printer.

Priority order, Spool print etc. in “Advanced” tab. “Advanced” setting follows MS Windows standard. If you want to change the setting, please refer to the Window manual.

(It is recommended to maintain default.)

In “Color management” tab, you can select color management profile fit to the printer.

SMART-31 uses color profile to express optimal color. The driver selects color profile automatically to fit each ribbon.

Figure 46 Advanced

(It is recommended to maintain default.)

Depend on the permission, the certain group or user can print, manage the printer/documents or not.

Figure 47 Color Management

Figure 48 Security

(6) Service

You can recognize the modules to connect,

printer serial, printer ID, driver version, firmware version, type of ribbon & balance and printer’s status.

You can print the “technical support sheet” on a card to check printer’s setup value.

To clean printer, please insert a cleaning card in a hopper and click “Clean Printer”. For further details, please refer to “6.2. Cleaning Printer”.

Figure 49 Service

4. Utilities

Password input window is displayed when

correct password, the recorded setup value

printer. So if you use another PC with same

Figure 50

When you are successful to log-in, you can

Figure 51

4.1. Card Printer Config

SMART-31 is produced with optimized setting. You need to adjust setting value if required or spare parts are replaced using CardPrinterConfig in our Installation CD.

You can adjust following settings with CardPrinterConfig.

(1) Run CardPrinterConfig

you run this program. If you input the

will be shown and you can change values. The password is saved to SMART-31

printer, previous password is required to run this program. (Default password is

none. Please press OK if you have not set password.)

set values shown as left picture.

CardPrinterConfig Log-in

CardPrinterConfig start

(2) Card Printer Basic Setup

①

②

③ ④ ⑤ ⑥

⑦

⑧

⑨ ⑩

Figure 52

① To show connected printers

Device: You can select a printer using pull-down menu. “IDP SMART-31 Card Printer” is a name of printer. “SMART1” is printer ID, “USB005” is connected port. If you connect the Network printer, please check the “Allow Network Printer” and select in the pull-down menu.

② To set administrator password and user password.

Change Root PW: To set administrator (root) password. This password is used to

verify user authority for CardPrinterConfig and User Authentication. Also it is required for User password management. (Please set password for security use.)

CardPrinterConfig – Card Printer Basic Setup

Change User PW: To set user password for User Authentication.

③ Click “ Card Printer” tab.(If laminator or flipper is installed, you can setup laminator or

flipper setting value by “Laminator” tab or “Flipper” tab..

④ To show firmware version, serial number of printer and serial number, resister & type of

print head.

⑤ To show print area. It shows

exaggeratingly for user convenience.

⑥ To set print area. Please set it properly to print on an entire card because SMART-31 is

a direct thermal card printer. When you click “⑦ Print”, a card is prin t ed as like “④ example”. Please set values properly that all circles of each corner are printed and

blank spaces are 0.4mm ~ 0.5mm in the top and the bottom of a card. Please set values by following order.

X Start Position: Please set right and left properly by adjusting X position.

Y Start Position: Please set the start position of printed example image and blank

space in the top is 0.4mm ~ 0.5mm.

Y End Position: Please set the end position of printed example image and blank

space in the bottom is 0.4mm ~ 0.5mm. It is recommended to set bigger value for “Y scale” than default.

Y Scale: Please set to show circles in the bottom.

To set density. SMART-31 enables to set different density for each color, resin black and overlay. So, please set each density for high quality. Please optimize the quality by adjusting each value. To optimize, you repeatedly adjust the density and print a Calibration card and check the print state until you get the optimum.

If your printer is SMART-31 R model, please do not install ribbon. You can set density with Rewritable cards. Please adjust total density only.

Total Density: To set all of the density (Color, Black and Overlay) at one time.

If your printer is SMART-31 R model, when the density i s t oo strong, you will have darker background color. (Background color may vary depending on card type.) When density is proper, texts and images are printed clearly and there is no background color. When density is too low, texts and images are printed dull.

Figure 53 SMART-31 R density

YMC Density: To set color density. Please maximize YMC density as you can, which enables to express range of color and vivid images. If it is too strong, green or r ed marks are appeared. If it is too weak, the print quality will be dull.

Figure 54 Color density

Black Density: To set resin black density. In the picture, barcode is printed to express density.

When density is too strong, barcode is printed too thick. When density is too weak, barcode is too thin. Please adjust resin black density to express clear barcode. Please refer to the following pictures.

Figure 55 Resin Black density

Overlay Density: To set overlay density. Please set it when overlay is printed on surface regularly. If it is too strong, it is hazy and marks are appeared. If it is too weak, overlay panel is not printed edge areas. You can check it with printed card under the light.

Figure 56 Overlay density

⑦ To print calibration card. ⑧ To show advanced Setup.

(It is recommended not to set advanced setup.)

⑨ To load or save values.

Get Config.: to get values from current printer Set Config. : to set values to current printer Load from File: to load values from file Save to File : to save values to file Close : to close CardPrinterConfig

(3) Card Printer Advanced Setup

①

②

③ ④

You can set more values.

Figure 57 CardPrinterConfig – Card Printer Advanced Setup

① You can set Printer ID, PC serial, Print head and Magnetic encryption key.

Change Printer ID: When SMART-31 is used by SDK, you can set unique ID for SMART31 printer regardless of whether it is connected by USB or what IP address is. It is useful to connect and use several printers. Default is “SMART”.

Set PC Serial: One of security function. You can use a printer with specific PC. It is activated when you click “Set PC Serial” after “PC Auth. ” of ④ is checked and

rebooted. At that time, the specific information of used PC is saved to SMART-31 printer.

Change Head: When you replace thermal print head, you must change head information for optimal quality. Please change head serial number, resistor and type of head in the Change Head Dialog window after click “Change Head”.

Set Mag. Encrypt Key: One of security function. When you use SDK, you can encrypt magnetic stripe encoding data transmitted by USB. You can define and save the encryption key to SMART-31 using “Set Mag. Encrypt Key”.

② To show how many cards are issued with SMART-31 printer. “Total Issue Count” is the

number of issued cards from factory shipment, “User Issue Count” is the number of issued cards from replacing head. When you replace a head, please initialize the number by ticking “Reset User Issue Count”.

③ To show ribbon motor management. SMART-31 recognizes ribbon color automatically and

controls motor by ribbon remaining. “RMP+”, “RMP-“, “RMM+”, “RMM-“ are necessary variables to control ribbon motor. Please do not change values for them as it affects card quality.

RMP+: Set the ribbon motor’s max torque value while printing when the balance is max. RMP- : Set the ribbon motor’s min torque value while printing when the balance is min. RMM+: Set the ribbon motor’s max torque value while moving when the balance is max. RMM- : Set the ribbon motor’s min torque value while moving when the balance is min. Ribbon Position: Set the ribbon arrangement position Ribbon Search Mode: Set the ribbon Search method Print Wait Time: Set the time from lifting down the print head to starting print Initial Flipper Angle: Set the angle of flipper when card is out if the ‘Card Out’ is ‘Back’

④ Please r ef er as below for other values.

Display Type: Set a type of LCD display m odule UART Baud Rate: Set the speed of communication of Internal Serial port. It is used for the

KIOSK model. Security: There are several ways to set a security function for SMART-31.

PC Auth.: You can use a printer with specific PC. It is activated when you click “Set PC

Serial”.

User/Root Auth.: You can set passwords for User and Administrator.

DCL Mode: When you use SDK and print cards with DCL mode, you don’t need to install

printer device driver.

SBS Only: Please enable it when you issue cards with software programed by SDK. This option disables printer device driver.

Safe Head Heat: Set not to print if the print head is overheated. Cleaning Warning: Set to show the ‘Do cleaning’ message periodically Use USB Serial: When SMART-31 is connected to USB, it transmits the USB serial

number to PC. Default is the same number used by all SMART-31. Please set this option when you use multiple SMART-31 printers connected to 1 PC via USB. It enables unique serial numbers for each USB.

Mag. Head Position: SMART-31 can install the magnetic encoder on upper/lower side of a card. You can set it depending on the position of encoder.

Card Out: Set the way to eject cards. Error Card Out: Set the way to eject error cards. Auto Front Card In: Set to input a card automatically if the front card-in sensor detects a

card. It is used for the KIOSK model. Auto Rear Card In: Set to input a card automatically if the rear card-in sensor detects a

card. It is used for the KIOSK model. Dump Mode: It records log data to inspect the operation of printer. User Mag. Current: The default current value when the user selects to use the defined

value when magnetic encoding Mag. Write Mode: You can order the way how to encode magnetic stripe.

“L:A, H:I”: encodes 3 tracks at once for LoCo card and encodes at twice by dividing 1,3 and 2 track for HiCo card.

Magnetic Start Position: Set the start position of magnetic stripe when you encode. Card In Speed: set the speed of inputting a card Card Move Speed: set the speed of moving a card Card Eject Speed: set the speed of ejecting a card

(4) Flipper Setup

① ②

This ‘Flipper’ tab is shown when the flipper option is installed.

Figure 58 CardPrinterConfig – Flipper Setup

① To show installed flipper

Firmware version and serial number of flipper

② To set configuration of flipper

Device Attribute: Basic attribute of flipper Card In Speed: Set the speed of inputting a card into a flipper

Cade Move Speed: Card Eject Speed: Set the speed of ejecting a card from the flipper

Set the speed of moving a card in the flipper

4.2. Network configuration

The printer which installed with

①

②

③

④

Please connect network cable

(Network cable is not supplied. Please ask

(1) Connecting network port

network option has a port for network connection as shown in the left picture.

Power Switch Power Supply Connector Network Port USB Port

(RJ45) to a printer.

network administrator for more questions.)

① ② ③ ④

Figure 59 Rear view of SMART-31 printer 1

Figure 60 Rear view of SMART-31 printer 2

DHCP (Dynamic Host Configuration Protocol) which automatically assigns IP address to the SMART31 network printer on the same network is default for IP configuration. If you don’t have DHCP server, you need to set static IP.

Please run NetAdmin.exe in the SMART-31 installation CD to set or change network configuration.

(2) Network configuration

NetAdmin is run as the Pic.72 after

When no printer is connected to

② ①

turning on SMART-31 network printer.

① Pr int er Connection Status

Searches local network, finds and shows available network printer.

② Net work Module Management

Searches connected encoder on network module. Reboots, Resets network module. Firmware upgrade available

③ Pr int er Configuration

Sets detailed system configuration.

④ Network Information

Shows firmware version of network module

③

④

Figure 61 Running the NetAdmin

network, there is no printer shown on the box.

Please click “Refresh”. If no printer shown, please check as

below,

1. Please check the printer is turned on.

2. Please check network cable is

connected to network hub and works properly (LED lamp blinking).

3. Please check if there is DHCP server

in the local network. When DHCP server is not in your local network, you need to set Static IP.

4. If Static IP is used, please check the

IP configuration. If another device uses same IP address, it doesn't work.

Figure 62 Network printer is not found

If you are unable to find printer in

local network, please connect printer

by USB. You can setup network by

printer by USB. Please connect a printer

Please select a proper printer and

USB.

When you click Refresh, you can find a printer connected by USB as shown in the left picture..

 You don’t need to install device driver

for network configuration by USB. Please ignore messages related to device installation.

 You can change values of “System

Management” only when you connect a

by network to use all of the functions of Netadmin.exe.

click “connect”. Please enter

password and click “OK”.

Default password is “admin”.

Figure 63 Connecting to USB port

Figure 64 NetAdmin Log-in

“USB port state” shows USB device

status connected on network

support PC/SC on network module, you

“Reboot module” reboots network

up window

module.

 Network module has 4 USB port s.  Network module supports PC/SC.

When you install the encoders that

can recognize the status of encoders.

module.

Figure 65 USB port state

 Please click “Yes” when pop-

comes out for reboot.

 It takes 1 minute to reboot.  Please click “Refresh” after reboot.

When proper printer shown, please connect printer by clicking “Connect”.

Figure 66 Rebooting the network module

“Reset to default” resets to default

and reboot network module.

up window

“Upgrade firmware” enables to

 Please click “Yes” when pop-

comes out for reset.

 It takes 1 minute to reboot.  Please click “Refresh” after reboot.

When proper printer shown, please connect printer by clicking “Connect”.

upgrade firmware of network

module.

Figure 67 Reset to default

 You can choose a f irmware file.

Figure 68 Upgrading the firmware 1



Warning box will be shown during

It is recommended not to do other work

Please do not turn off a printer until the

When firmware upgrade is completed,

firmware upgrade for network module.



during firmware upgrade for system reliability.



upgrade is completed.

Figure 69 Upgrading the firmware 2



pop-up comes out for reboot. Please click “Yes”.

 It takes 1 minute to reboot.  Please click “Refresh” after reboot.

When proper printer shown, please connect printer by clicking “Connect”.

Figure 70 Upgrading the firmware 3

If you setup network automatically,

please choose DHCP.

Static IP is recommended. DHCP server

We recommend using Static IP because

Wireless Network Configuration

Enter the ESSID value in “WiFi ESSID”

 Please select DHCP or Static.  “DHCP” is default for SMART-31 printer.  Please enter values for “IP”, “Network

Mask”, and “Gateway”. Click “Set Configuration”.



assigns IP address automatically but this IP address is temporary, so the IP address may be changed. In this case, the network error may occur in connecting to SMART-31 network printer.

 If you are not aware of static IP, please

ask network administrator for Static IP.



it is more stable for using SMART-31 network printer.

Figure 71 Dynamic IP configuration

 For wireless network, the WIFI option

should be installed in the Network Module

 Check “WiFi (Option)” button to activate



to access

 Enter the Key value in “WiFi Key”  Set the IP address as the same way of

LAN network

 Click “Set Configuration” to save the

configuration value and reboot the printer

Figure 72 Static IP configuration

You can change Service

Configuration.

You can use Open Card Print

This function is for send commands and print through network card regardless of

 SMART-31 network printer provides 3

kinds of service (change “USB Spool”, “Network Spool” and “Network SDK”). You can select and change the service according to the need.

 In “Network SDK”, you can control the

printer and print a card well, and the printer supports SSL (Secure Sockets Layer) and User Authentication for security.

 Please use default and ask t echnician

for details.

function.

Figure 73 Network service configuratio n



 Click check box “Use OCP”  “Use Terminal Emulation” is value for

getting echo according to the commands through terminal. For security, it supports SSL and User Authentication.

 Please do not change default value

except special case.

Figure 74 OCP configuration

You can add, change, delete User

and change its password.

 “admin” is administrator and you can’t

delete this account. Please don’t forget password for “admin”

 “Get User”: shows available users  “Add User”: makes new user  “Del User”: deletes selected user  “Change Password”: changes password

Figure 75 Network user configuration

4.3. Card Printer Test

① ② ③

④

⑤

⑥

⑦

Basically Card Printer use standard printer device so you can be used same as general paper printer. In the case of magnetic stripe, contact, contactless encoder option, you will need to install appropriate driver and operate individually. Encoding operation will be controlled by “CARD PRINTER SDK”. You can test all feature of printer by Card printer Test. Card Printer Test program is developed by using “SMART Printer SDK”

(1) CardPrinterTest

When CardPrinterTest is run, all function can be tested individually.

Figure 76 CardPrinterTest

① Sel ect Printer: select printer to test. In the picture, “IDP SMART-31 Card Printer” is the

Printer name, SMART1 is the Printer ID, and USB005 is the connected port.

② Cont rol : To execute each step to test

③ Print: Print test with CSD file which is designed by Smart ID program.

④ Bat ch Start: Repeat selected encoding test by “⑤ Encoding”

⑤ Encoding: Encode Magnetic Stripe, Contact Card, Contactless Card

⑥ Printer Status: Check printer status.

⑦ Message: Description of status by log.

(2) Select printer and control

When you execute CardPrinterTest, it will search connected printers by USB and Network automatically and SMART-31 printer connected to USB has higher priority. Other printers could be selected by pull-down menu. You can test all function with connected printer.

. Control is consisted by SBS(Step by Step), Move, Rotate, Etc. section and you can control printer by each step.

 SBS

SBS is to operate SMART-31 printer in SBS(Step-By-Step) mode which you can control the printer using commands. In SBS mode, after printing data transmission, printing a card will be run only by clicking “DoPrint”. It is the main difference between NORMAL mode and SBS mode. When you click “Start”, SMART-31 is operated in SBS mode, and existing spooled data will be eliminated. To exit SBS mode, click “Stop”.

 Card

Card is to bring a card into printer and eject a card. “In” is to move a car d from input hopper to printer and “Out” is to move a card from printer to output hopper. In case the flipper is installed, “Back” ejects a card to the back side.

 Move

Move i s to move a card to specific position in the inside of printer. “Print” is to move a card to the printing position, and “Mag.” is to the magnetic encoding position, and “IC” is to the contact smartcard encoding position, and “RF” is to the contactless smartcard encoding position. “To Rotator” is to move a card from printer to flipper and “From Rotator” is to move a card from flipper to printer. “from In” is to move a card from the card in sensor to

where you define position, and “from Out” is to move a card from the card out sensor to where you define position.

 Rotate

Rotator is to flip over a card in the printer installed flipper. “Auto” is to move a card from printer to flipper and flip over a card and move a card to the printing position automatically. “Batch” is to repeat “Auto” as many times as the number of set. “To Bottom” is to turn to the backside of card and “To Top” is to turn to the front side of card.

 Etc

“Cleaning Roller” is to clean the roller by cleaning card automatically. “Use Log” is to

display log in message space.

(3) Print

Pr int can be done through the CSD file which is designed by Smart Design program. Following the

steps in this section.

1. Click “…” button and select the CSD file.

2. Click “Open” button to prepare CSD file to print.

3. Click “Print” Button to move print data to spool. In the NORMAL mode, Click “Print” button

to print a card, but in the SBS mode, “Print” button to transmit a printing data from PC to printer and wait for printing. Therefore, you must click “DoPrint” to print in SBS mode. This function is for detail control of printer.

4. Click “Close” button to close CSD file.

(4) Batch

Batch is to repeat encoding/decoding test continuously. In the Repeat, you input the number of repeat and click “Batch Start”, then the test is run as many times as the number of set. When you check “Include Card In/Out”, each time the printer bring a card from input hopper and perform an encoding test and eject the card. But if not, encoding test will be done only by one card. At that t ime, if there is no card in the printer, the printer bring a card into the printer from input hopper and repeat the encoding test on the card, and if there is a card in the printer, t he encoding test is performed on the card repeatedly. “Card Holding” is activated when “Include Card In/Out” is ticked. When “Card Holding” is ticked and the repeat number is set, the printer repeats the encoding test as many times as the number of set in the “Card Holding” without ejection. When it is completed, the printer ejects the card and brings a new card into the printer and starts testing.

In the Settin g, “Retry” is to retry the encoding test when the error occurred. “Prompt on Error” is to display Pop up Message when the error occurred. If not, Error number will be counted without message. The number of error is displayed at Error section.

(5) Encoding

Magnetic: Magnet Stripe Encoding

“Read” is to read and display the data from magnetic stripe card. It is composed of “Do

Read” and “Read All Buffer” and runs “Do Read” and “Read All Buffer” sequentially.

“Do Read” is to read the data from magnetic stripe card and store the data in the buffer. “Read All Buffer” is to transmit the date stored in the buffer to PC. If the track number is

ticked, the data of the ticked track is only transmitted to PC. “Write” is to write the data to the magnetic stripe. It is composed of “Write All Buffer” and

“Do Write” and runs “Write All Buffer” and “Do Write” sequentially.

“Write All Buffer” is to transmit the data to the buffer. “Do Write” is to write the data stored in the buffer to the magnetic stripe of card. You can

choose the magnetic foil type (LoCo or HiCo) and the track of magnetic stripe. “Random Fill” is to create a random magnetic encoding data for testing.

Batch process repeats the following steps sequentially, Card “IN”  Move “Mag”  Magnetic “Random Fill”  Magnetic “Write”

 Magnetic “Read”  Card “OUT”.

Figure 77 Magnetic stripe encoding

IC(PC/SC) : Contact Smartcard Encoding

In SMART-31 printer, a contact smartcard encoder can be installed and SMART-31 printer supports the contact smartcard encoder in the printer inside. “IC(PC/SC)” is to test a contact smartcard encoding.

“ICH Contact” is to bring the encoder head into contact with the IC chip of smartcard physically.

“ICH Discontact” is to separate the encoder head from the IC chip of smartcard physically. “Init” is to recognize and display the installed contact smartcard reader. The recognized

encoder will be displayed at the pull down control.

“Contact” is to contact with the smartcard electrically and initialize. “Reset” is to finish the function electrically. After “Contact”, you can run “Get ATR”, “Read”,

“Write” and “Clear”.

“Get ATR” is to read the ATR data.

“Read” and “Write” are to read and write the defined data (Name, Address and Phone).

These could not be applied to all cards. “Clear” is to clear the displayed data (ATR, Name, Address and Phone).

In case the data is read and written using APDU, Read/Write can be done by APDU commands.

“Load APDU” is to read the stored APDU commands. “Save APDU” is to save the displayed APDU commands. “Clear APDU” is to clear the APDU section. “Send APDU” is to run the APDU commands.

Batch process repeats the following steps sequentially, Card “IN”  Move “IC”  IC “ICH Contact” “OUT”.

 IC “Init”  IC “Contact”  IC “Reset”  IC “ICH Dis-contact”  Card

Figure 78 Contact smartcard encoding

RF(PC/SC) : Contactless Smartcard Encoding

In SMART-31 printer, a contactless smartcard encoder can be installed and SMART-31 printer has the internal and external contactless smartcard encoder. RF(PC/SC) is to read and write the contactless smartcard. Using internal encoder, the printer brings a card into the printer from input hopper and encodes a smartcard. Using external encoder, after putting a card on the top cover, you can encode because the antenna installed under the top cover is used. Therefore, “Batch” is applied only to the internal contactless smartcard encoding.

“Contact” is to contact with the contactless smartcard electrically and initialize. “Reset” is to finish the function electrically. After “Contact”, you can run “Read”, “Write” and

“Clear”.

“Get UID” is for getting Chip Serial Number(CSN) “Read” and “Write” are to read and write the defined data (Name, Address and Phone).

These could not be applied to all cards. “Clear” is to clear the displayed data (ATR, Name, Address and Phone).

In case the data is read and written using APDU, Read/Write can be done by APDU commands.

Batch process repeats the following steps sequentially, Card “IN”  Move “RF”  RF “Connect”

 Get UID RF “Di scont act”  Card “OUT”

Figure 79 Contactless smartcard encoding

(6) Printer status

“Get Temperature” is to get and display the temperature of Thermal Print Head. When the

“Realtime Check” is ticked, it displays the current temperature of Thermal Print Head in real time.

“Get Status” is to get and display the printer status.

Please refer to the ‘SMART SDK manual’ for the status code.

4.4. Firmware update

(1) CardPrinterFirmware Menu

Select

(2) Ready for Firmware Update

When you run the CardPrinterFirmware, you can see the pop-up window.

Device: Select the local printer that you want to upgrade.

Card Printer / Flipper / Laminator: the device you want upgrade.

Device Version: Displays the current firmware version of selected printer.

Binary File: Click “Browse” button and select new firmware file to update.

Figure 80 Run CardPrinterFirmware

Manual Update: It is used when you want to update manually.

Update: Updates automatically. In generally, we recommend updating automatically.

Close: Exit.

Message : It displays information of

updating.

 Select the printer to updat e the

firmware on the ‘Device’ list.

 Select the device to update the

firmware among Printer/Flipper/Laminator tab. The Flipper and Laminator tab is shown if that option is installed only.

 Click “Browse” and select the new

firmware

Figure 81 Select Firmware

(3) Firmware Update

 Click “Update” button to upgrade

In case there are some problems in the

up widow

as below picture. It shows procedure of

dialog box until it is completed successfully

automatically, then the printer is upgraded after rebooting.



automatic upgrade, you click “Manual Update” and can see the pop-

manual upgrade. You can upgrade manually according to this procedure.

(Caution: Please do not close upgrade

and do not turn off the printer.)

Figure 82 Update Firmware

5. Optional device driver installation

In SMART-31 printer, you can install the optional devices that encode contact smartcard or contactless smartcard. If your purchased SMART-31 printer has optional devices, you should also install the smart card reader drivers.

5.1. Contact smartcard reader

In SMART-31 printer, you can install the two types of optional devices which are contact smartcard reader. If you have one or more smartcard reader devices on your printer, you should install the smartcard device driver as in the following, and connect SMART-31 printer to your PC.

(1) Run the smartcard driver installer

Insert the smartcard installation CD and find “\Options\Gemalto PC Twin” directory on your CD. Find the right directory which is installed OS version on your PC, and r un the installer. You can see the smartcard reader driver installation window as the Pic.125. And click “Next”.

Figure 83 Contact smartcard reader driver installation

(2) License agreement

The license agreement window is shown. Check at the agreement and click “Next”.

(3) Installation

Figure 84 License agreement

The installation message is shown as the picture. Click “Install” to install driver.

Figure 85 Installing the contact smartcard reader driver

(4) Complete installation

When the installation is completed, the window is shown. Click the “Finish” to complete the installation steps.

Figure 86 Completing the smartcard reader driver installation

5.2. Contactless smartcard reader

In SMART-31 printer, you can install the two types of smartcard reader which are internal contactless smartcard reader and external contactless smartcard reader. If you have one or more contactless smartcard reader devices on your printer, you should install the contactless smartcard device driver as in the following, and connect SMART-31 printer to your PC.

(1) Connect SMART-31 printer to P C

When you connect the printer to PC and turn on the printer, you c an see the “Found New Hardware Wizard” as the picture, then Check “No, not that time” and Click “Next” to continue.

Figure 87 Found New Hardware Wizard

(2) Choose the installation method

At the window as the picture, select “Install from a list or specific location” and click “Next”.

Figure 88 Installation method selection

(3) Driver location

Insert the smartcard installation CD and find “\Options\ Omnikey 5121” directory on your CD. Find the right directory which is installed OS version on your PC, and select the directory as the picture, and click “Next”.

Figure 89 Driver location

(4) Complete installation

When the installation is completed, the window as the Pic121 is shown, click “Finish” to complete the installation steps.

Figure 90 Completing the driver installation

6. Troubles hooting

LCD Message

Description and Countermeasures

Fail to move a card from the hopper to the printer inside.

Fail to move a card in the printer.

Fail to move a card between printer and other module(flipper/laminator)

Fail to discharge a card after printing, encoding or laminating.

The Head Up/Down Motor or Sensor don’t work correctly in printing or booting up

The IC Head Up/Down Motor or Sensor don’t work correctly in printing, encoding

6.1. Error Message

SMART-31 printer shows the error message in the LCD display when it occurs. Click the Left button to retry or the right button to cancel an operation.

The following shows the error message on your Smart Printer. For checking a status of printer, please use a CardPrinterTest or CardPrinterDiagnostics in the Utilities folder of Install CD.

-. Check the card thickness and adjust the card thickness control lever

1 Card In Error

-. Check cards are stuck because of static electricity

2 CardMove Int Err

3 CardMove Ext Err

4 Card Out Erro r

-. Clean Hopper roller and cleaning roller

-. Remove a card if the ribbon is attached

-. Check the rollers and cards, and clean them if they are polluted

-. Check the operating state of the card feeding rollers and sensors

-. Check the rollers and cards, and clean them if they are polluted

-. Check the operating state of the card feeding rollers and sensors

-. Remove a card if the ribbon is attached

-. Check the rollers and cards, and clean them if they are polluted

-. Check the operating state of the card feeding rollers and sensors

5 TPH UpDown Error

6 IC UpDown Error

-. Check the operating state of the Head Up/Down Motor and Sensor.

-. Check the status of the mirror sticker in the Head Up/Down Gear.

or booting up.

-. Check the state of the Cable between a module and a main board

-. Check the operating state of the IC Motor

The printer can’t search the ribbon panel in printing or booting up

The printer can’t wind the ribbon in printing or booting up.

Fail to read or write the magnetic stripe.

Fail to read a track 1 of the magnetic stripe.

Fail to read a track 2 of the magnetic stripe.

Fail to read a track 3 of the magnetic stripe.

Error occurs while printing

-. Check the operating state of the Ribbon Motor

7 Ribbon Seek Err

8 Ribbon Move Err

9 MAG R/W Error

10 MAG T1 Error

-. Check the operating state of the ribbon encoder sensor and gears

-. Check and clean the Color In/Out Sensor

-. Check the operating state of the color in/out Sensor

-. Check the operating state of the Ribbon Motor

-. Check the operating state of the ribbon encoder sensor and gears

-. Check the surface and direction of magnetic card

-. Check the coercivity of magnetic card and enc oding configuration

-. Check the rollers, encoder and cards, and clean them if they are polluted

-. Check the surface and direction of magnetic card

-. Check the coercivity of magnetic card and enc oding configuration

-. Check the rollers, encoder and cards, and clean them if they are polluted

-. Check the surface and direction of magnetic card

11 MAG T2 Error

-. Check the coercivity of magnetic card and enc oding configuration

-. Check the rollers, encoder and cards, and clean them if they are polluted

-. Check the surface and direction of magnetic card

12 MAG T3 Error

-. Check the coercivity of magnetic card and enc oding configuration

-. Check the rollers, encoder and cards, and clean them if they are polluted

13 Printing Error

-. Check a card is jammed

-. Check usage of a genuine ribbon and cards

-. Check the rollers, encoders and cards, and clean them if they are polluted

14 Init Error

Error occurs while initializing

Fail to communicate between a printer and a flipper/laminator

Error occurs while laminating

Error occurs while operating a flipper

All ribbons are used

Ribbon is not installed or not searched

Thermal Print Head is not installed or not recognized

Thermal Print Head is overheated

Error occurs when the abnormal printing data is transmitted.

-. Check the status of installation of ribbon and laminating film

-. Check the laminator tur n ing on if the laminat or is installed

15 DeviceCon Error

16 Lami Error

17 Flipper Error

18 Ribbon Zero

19 RibbonNotFound

-. Check the laminator turning on if the laminator is installed

-. Check a cable between a printer and a flipper/laminator

-. Remove a card after opening a laminator top cover

-. Check usage of a genuine laminating film and cards

-. Remove a card after opening a flipper cover

-. Check the card size

-. Install the new ribbon after purchasing it in the place of purchase

-. Install a ribbon if not

-. Check usage of a genuine ribbon

20 TPH Not Found

21 TPH Over Heat

22 Invalid Data

-. Check the print head installation

-. Contact the place of purchase

-. Lower the temperature when the temperature of circumstance is too high

-. Take a stop for 10 minutes and print again.

-. Contact the place of purchase if this message is shown regularly

-. Replace the USB cable USB

-. Change the USB port in the PC

-. Reinstall the printer driver

23 Wrong Password

The password is not correct

Failed to execute a command of the printer

The printing data is full in the spooler

24 SetCommandFail

-. Input the correct password

-. Contact the place of purchase if you forget the password

-. Replace the USB cable USB

-. Change the USB port in the PC

-. Turn off/on the printer

25 Spool Full

-. This message disappear after printing all data to send

-. Turn off/on the printer if the spool data is full without printing

6.2. Cleaning the print e r

To maintain the best condition of SMART-31 printer, you must clean the printer periodically. If you use the exclusive long cleaning card as the picture, you can clean the printer easily. For purchase the exclusive long cleaning card, ask t o SMART-31 printer provider.

Figure 91 Exclusive long cleaning card for SMART-31 printer

If the exclusive long cleaning card is ready, click the “Clean Printer” in the service tab of SMART-31 printer driver. After click, Clean Printer program to clean the printer is run.

Or, you can set the

opening the top cover.

Cleaning Mode with LCD buttons by pushing both buttons for 5 seconds after

Figure 92 Printer cleaning start

Step 1. Connect the SMART-31 printer to PC and turn it on, and prepare the exclusive long

cleaning card.

Figure 93 Printer cleaning Step 1

Step 2. Open the hopper and top cover and remove the card and ribbon cartridge.

Figure 94 Printer cleaning Step 2

Step 3. Insert the exclusive long cleaning card into the printer through input hopper. When the

exclusive long cleaning card is inserted to the cleaning roller, it will be move automatically. It is normal that the exclusive long cleaning card is inserted to the ends and rollers are moving to clean.

Figure 95 Printer cleaning Step 3

Step 4. Close the top cover to clean the Thermal Print Head and the printing roller. When the

top cover is closed, cleaning card will be moving back and forth to clean.

Figure 96 Printer cleaning Step 4

Step 5. Wait until the cleaning is completed. When the cleaning is completed, the exclusive

long cleaning card will be ejected automatically as the picture.

Figure 97 Printer cleaning Step 5

Step 6. Remove the exclusive long cleaning card and install ribbon cartridge into the printer.

Figure 98 Printer cleaning Step 6

6.3 TPH (Thermal Print Head) replacement

1. Check the serial number and the Head as

resistance of new Thermal Print the Picture.

TPH type: A = KEE, B = KPE Serial No.: see the red box. TPH resistance: see the green box.

Figure 99 Thermal Print Head

2. Set up the new Print Head’s configuration using CardPrinterConfig program.

Step1: Run ‘CardPrinterConfig’ in Utilities of the installation CD and click expansion button. Step2: Click “Change Head” in the extended setup. Step3: Input the Print Head’s Serial No., Resistance and Type (choose KEE or KPE) on the

Print Head’s label, and click “OK”. Step4: Click “Set Config” to set the new Print Head’s configuration.

Figure 100 Print head setup

4. Replacing the new Print Head

6. Calibration of Print Head Angle

Head should be located vertically with

d make good quality

adjust, and turn the screw by 90

Step1: Remove the old Print Head from the top cover.

(1) Turn off the printer and open the top cover. (2) Hold the Print Head and press the locked hook, then the Print Head is

disconnected..

(3) Disconnect the Print Head from print head wire carefully.

(Caution: Print Head is possible to HOT.)

Step2: Installing the new Print Head

(1) Connect new Print Head to the print head wire. (2). Put the new Print Head on the Shift and pull it up until be locked..

5. Setup the print position and the color density.

After installing the new Print Head, you must reset the print position and the color density using CardPrinterConfig utility. Refer to “4.1.2 Default sett ing”

To get the best print quality, the Print

card surface. If print quality has the problem, it

could be caused by print head angle. Through Adjusting print head angle

by screw (red mark in the right picture), you coul of prin t.

Figure 101 Print head replacement

Figure 102 Print head angle

(Use the appropriate screw driver to

degrees at a time.)

6.4. Card movement

6.4.1. Cards can’t enter into the printer from input hopper.

 Non-standard cards or bad cards.

Change the cards. You can use only ISO CR-80 card (54mm x 86m m).

 Card thickness control lever is set improperly.

Regulate the card thickness control lever to fit the current card thickness.

 Bad card array.

Array the cards again and put them on input hopper as section 2.4 in this manual.

 Cards have static and moisture.

Remove the moisture or static.

6.4.2. Card Transfer Error occurs when the ribbon is coiled around the transfe r roller or the printing roller.

Open the top cover and remove the card and the coiled ribbon from SMART-31 printer using front LED buttons. If this problem occurred frequently, check the below things.

 Non-standard cards or bad cards.

Change the cards. You can use only ISO CR-80 card (54mm x 86mm).

 The transfer roller or the printing roller is contaminated with the dust and dirt

Remove the dust and dirt with the cleaning kit as section 6.2

 Wrong printing position setting.

Please contact the local supplier

 When operating temperature and humidity is out of the acceptable operating limit of

the printer. Adjust the operating environment of the printer.

6.4.3. An Error occurs while the card is being transferred.

First of all, check the Error message at LCD display.

Figure 103 Printing quality trouble 1

Figure 104 Printing quality trouble 2

Open the top cover and remove the card by LED buttons. If this problem occurs frequently, check the followings.

 Non-standard cards or bad cards.

Change the cards. You can use only ISO CR-80 card (54mm x 86m m).

 Printer setting is changed or is not proper.

Please contact the local supplier.

 The transfer roller or the printing roller is contaminated with the dust and dirt.

Remove the dust and dirt with the cleaning kit as section 6.1.

 The card surface is contaminated with the dust and dirt.

Check the card surface and remove the dust and dirt and try again. If this pr oblem occurs again, retry with new card.

6.5. Printing quality

6.5.1. Not printed or wrong colors printed spot.

 The card surface is contaminated with the

dust and dirt.

After checking the card, change it to another card.

 The cleaning roller is contaminated with the

dust and dirt.

Check the cleaning roller. If there is much dust, change the cleaning roller to the new one.

 Much dust in the printer.

Clean the inside of the printer with the cleaning kit.

6.5.2. Not printed horizontal line.

 The ribbon cartridge is installed improperly.

Check the ribbon cartridge installation state and whether the ribbon has wrinkles.

 The printer head is contaminated with the

dust and dirt.

Clean the printer head with cleaning kit.

Figure 105 Printing quality trouble 3

Figure 106 Printing quality trouble 4

 The printer head is damaged.

Please contact the local supplier to replace the printer head.

6.5.3. Unclear or not uniform print.

 Uneven or bad card surface.

Change the card.

 Too high or low setting of the color density.

Please contact the local supplier. The color density default of your printer needs to be changed.

 The printer head is contaminated with the

dust and dirt. Clean the printer head with cleaning kit.

6.5.4. Not aligned color print.

 Non-standard cards or bad cards.

Change the cards. You can use only ISO CR-80 card (54mm x 86mm).

 Uneven or bad card surf ace.

Change the card.

 The transfer roller or printing roller is

contaminated with the dust and dirt.

Clean the rollers with the cleaning kit as section 6.1.

 Worn-out printer.

Please contact the local supplier.

6.5.5. Unplanned color print.

 Non-standard cards or bad cards.

Change the cards. You can use only ISO CR-80 card (54mm x 86mm).

 Uneven or bad card surf ace.

Figure 107 Printing quality trouble 5

Change the card.

 The transfer roller or printing roller is

contaminated with the dust and dirt.

Clean the rollers with the cleaning kit as section 6.1.

 Worn-out printer.

Please contact the local supplier.

6.6. Magnetic stripe encoding

6.6.1. Magnetic encoding error.

 The magnetic head is contaminated with the dust and dirt.

Clean the magnetic head with the cleaning kit.

 The magnetic encoding data is not transmitted or the wrong data is transmitted.

Check the setting of the program and the driver and the magnetic encoding data you transmitted.

 The card is not magnetic card, or inserting direction is wrong.

Change the card or the direction.

 Bad magnetic stripes on the card.

Change the card.

6.7. General operati on

6.7.1. Ribbon snapped during printing.

Open the top cover and take out the cartridge. After putting the snapped pieces on

together, install the cartridge again. Check the followings if this kind of problem occur frequently

 Non-standard cards or bad cards.

Change the cards. You can use only ISO CR-80 card (54mm x 86m m).

 Too high or low setting of the color density.

Please contact the local supplier. The color density default of your printer needs to be changed.

6.7.2. Watchman Message “Ribbon Not Found”

Open the Top Cover and check the status of ribbon installation. If it occurs frequently, check the followings

 Not genuine ribbon.

Change to the genuine ribbon.

 Ribbon i s consumed.

Printing is not possible if ribbon is used up. Change the ribbon.

 Snapped ribbon.

Open the top cover and take out the cartridge. After putting the snapped pieces on together, install the cartridge again.

6.7.3. Printer doesn’t operate even if the printing data has been transmitted. Check the following.

 Printer power off.

Check the power. Turn on the printer power. Check the printer adaptor whether it is connected with a socket and the printer.

 Bad power adaptor.

Please contact the local supplier for replacement of the adaptor.

 The printer driver is “Offline”.

Change the printer driver to “Online”.

 The printer’s USB cable is disconnected or the connection is bad.

Check the cable’s connection between PC and the printer. If not good, make the USB cable connection again.

 Bad USB cable.

Change the USB cable.

 The printing is operated with another printer driver.

Select the correct SMART-31 printer driver again.

 Wrong USB port setting of the printer driver.

Check the port setting of the printer driver and change the port setting.

 No ribbon in the printer or error occurred.

Install ribbon in the printer or resolve the error.

 Too long power or USB cable (more than 1.5M).

Use the cable provided with the printer.

 PC’s USB port is down:

Reboot your PC.

7. Specification

Model

SMART-31S

SMART-31D

Printing

Print Type

Dye-Sublimation

Print Area

Edge to Edge

Resolution

300dpi

Dual Side Printing

Option (with Flipper)

Yes

Card

Card Feeding

Automatic

Card Size

ISO CR80

Card Thickness

0.38mm (15mil), 1.0mm (40mil)

Printing Speed

YMCKO

Max. 23 sec./card (156 c ards/hour)

Max. 29 sec./card (124

Capacity Input Hopper

80 Cards

Output Hopper

25 Cards

System

Memory

64MB RAM

Control Panel

1 LED Button

Supported Platforms

MS Windows 7/ 8/ 10, Mac OS, Linux

Communication

USB, Ethernet (Option)

Power Supply

DC 24V, 2.0A

Power Consumption

Temp. / Humidity

Dimensions Millimeter (WxLxH)

172 x 377 x 190

172x 472 x 190

Inch (WxLxH)

6.8 x 14.8 x 7.5

6.8 x 18.6 x 7.5

Weight

Kg / Lbs

3.4 / 7.5

4.2 / 9.5

Encoding Options

Magnetic

ISO 7811 (Track I, II, III Read/ Write, HiCo/ LoCo), JIS II

Contact

ISO 7816 (ID-1)

Contactless

MIFARE, ISO 14443 (Type A/ B), ISO 15693, DESFIRE, iCLASS

Certifications

Card Type PVC, PET, Composite PVC

Monochrome 5 sec./card (720 cards/hour)

YMCKOK _

cards/hour)

15~35℃ / 35~70%

CB, CE, FCC, KC, CCC

Specifications and availability may change without notice.

 RFID(13.56MHz) Usage

The RFID Tag is used for the security and the recognition of the ribbon. To get the optimized printing quality on the printed card, the genuine ribbon of IDP should be used to print cards by using SMART printer. SMART printer can recognize the genuine ribbon by reading the encoded information on the RFID Tag of the ribbons. To support user’s various requirements for printing cards appropriately, many kinds of ribbons should be provided and SMART printer should distinguish the type o f ins talled ribbon. To distinguish the installed ribbon type correctly, SMART printer reads the encoded information on the RFID Tag of the ribbons. According to the installed ribbon type and the ribbon supplier, the printer driver of SMART printer can select the color profile and create the printing data.

IDP SMART 31 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1. Introduction

1.1 Printer outside features

1.2 Printer inside features

1.3 Ribbon cartridge features

① Ribbon cartridge

② ③ Take up & Supply parts

④ Disposable cleaning roller

1.4 Display and Buttons

2. Printer installation

2.1. Connecting a power and a USB cable

2.2. Fitting the ribbon

2.3. Loading the cards

2.4. The withdrawal of printed cards.

2.5. Driver installation (Windows 7 / 8 / 10)

3. Driver configuration

3.1. Printer P roperties

3.2. Advanced Options

3.3. Other settings

4. Utilities

4.1. Card Printer Config

This ‘Flipper’ tab is shown when the flipper option is installed.

4.2. Network configuration

4.3. Card Printer Test

4.4. Firmware update

5. Optional device driver installation

5.1. Contact smartcard reader

5.2. Contactless smartcard reader

6. Troubles hooting

6.1. Error Message

6.2. Cleaning the print e r

6.3 TPH (Thermal Print Head) replacement

6.4. Card movement

6.5. Printing quality

6.6. Magnetic stripe encoding

6.7. General operati on

7. Specification